Panasonic Kx Taw848 PC Cprogramming Manual

							2.15 [9] CO & Incoming Call
PC Programming Manual 411
DIL
For each CO line to which DIL distribution is set, different DIL destinations can be programmed 
depending on the time mode (day/lunch/break/night). Generally, DIL distribution is used for CO line 
calls from analog CO lines. Tenant number and VPS trunk group number can also be programmed 
for each CO line.
 
To assign DIL destination numbers, enter directly or click Extension Number of DIL Destination 
Setting (see 
2.1.6 Extension Number Setting).
Slot
Indicates the slot position of each CO line card (reference only).
Default
Current slot number
Value Range
Slot number
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
None
Por t
Indicates the por t number (reference only).
Default
Current port number
Value Range
Port number
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
None 
						

							2.15 [9] CO & Incoming Call
412 PC Programming Manual
Card Type
Indicates the CO line card type (reference only).
Default
Current card type
Value Range
Card type
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
1.9.8 INCOMING CALL FEATURES
DIL Destination—Day, Lunch, Break, Night
Specifies the DIL destination in each time mode.
Default
Not stored.
Value Range
Max. 4 digits (consisting of 0–9)
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
1.4.5 DIL (Direct In Line)
Tenant Number
Specifies the tenant number, to determine the Time Table by which calls are distributed depending 
on the time of day.
Default
1
Value Range
1–8 
						

							2.15 [9] CO & Incoming Call
PC Programming Manual 413
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
2.8.5 [2-4] Week Table
Feature Manual References
1.4.5 DIL (Direct In Line)
1.17.2 Tenant Service
1.17.4 Time Service
VM Trunk Group
Specifies the number of the VPS trunk group sent to the VPS when the DIL destination is the floating 
extension number of a VM (DPT) Group.
 
The VPS trunk group number is used to allow the VPS to send the applicable greeting message to 
the caller.
Default
1
Value Range
1–48
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
1.4.5 DIL (Direct In Line)
1.19.4 Voice Mail DPT (Digital) Integration
CLI for DIL
When CLI distribution is enabled for a CO line to which DIL distribution is set, incoming CO line calls 
will be distributed to the CLI destinations (instead of the DIL destinations) if the callers identification 
number is found in the System Speed Dialing Table.
 
CLI distribution can be enabled or disabled for each time mode (day/lunch/break/night) on a CO line 
basis.
Slot
Indicates the slot position of each CO line card (reference only).
Default
Current slot number 
						

							2.15 [9] CO & Incoming Call
414 PC Programming Manual
Value Range
Slot number
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
None
Por t
Indicates the port number (reference only).
Default
Current port number
Value Range
Port number
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
None
Card Type
Indicates the CO line card type (reference only).
Default
Current card type
Value Range
Card type
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None 
						

							2.15 [9] CO & Incoming Call
PC Programming Manual 415
Feature Manual References
1.9.8 INCOMING CALL FEATURES
CLI Ring for DIL—Day, Lunch, Break, Night
Enables CLI distribution in each time mode.
Default
Disable
Value Range
Disable, Enable
Maintenance Console Location
2.15.2 [9-2] DIL Table & Port Settings
Programming Manual References
None
Feature Manual References
1.3.10 CLI (Calling Line Identification) Distribution
1.4.5 DIL (Direct In Line)
2.15.3 [9-3] Miscellaneous
The Intercept Routing feature can activate when the destination of an incoming CO line call is 
unavailable, or when there is no destination for the call, to reroute the call to an alternate destination.
Intercept—Intercept Routing - Busy (Destination is busy)
Enables the Intercept Routing—Busy feature to activate when the original destination is busy.
Default
Disable (Busy Tone)
Value Range
Disable (Busy Tone): Sends a busy tone to the caller. (However, a call through an LCOT card will ring 
at the original destination while the caller hears a ringback tone.)
 
Enable: Redirects the call to the intercept destination
Maintenance Console Location
2.15.3 [9-3] Miscellaneous
Programming Manual References
None 
						

							2.15 [9] CO & Incoming Call
416 PC Programming Manual
Feature Manual References
1.9.9 Intercept Routing
Intercept—Intercept Routing - DND (Destination sets DND)
Enables the Intercept Routing—DND feature to activate when the original destination is in DND 
mode.
Default
Enable
Value Range
Disable (Busy Tone): Sends a busy tone to the caller. (However, a call through an LCOT card will ring 
at the original destination while the caller hears a ringback tone.)
 
Enable: Redirects the call to the intercept destination
Maintenance Console Location
2.15.3 [9-3] Miscellaneous
Programming Manual References
None
Feature Manual References
1.4.8 DND (Do Not Disturb)
1.9.9 Intercept Routing
Intercept—Routing to Operator - No Destination (Destination is not 
programmed)
Enables the Intercept Routing—No Destination feature to activate when there is no destination for the 
call. (The Intercept Routing—No Destination feature always works for calls through an LCOT card, 
even when this feature is disabled.)
Default
Enable
Value Range
Disable (Reorder Tone): Sends a reorder tone to the caller 
Enable: Redirects the call to an operator
Maintenance Console Location
2.15.3 [9-3] Miscellaneous
Programming Manual References
None
Feature Manual References
1.9.10 Intercept Routing—No Destination 
						

							2.16 [10] Maintenance
PC Programming Manual 417
2.16 [10] Maintenance
2.16.1 [10-1] Main
SMDR
Station Message Detail Recording (SMDR) automatically records detailed information about 
incoming and outgoing calls.
SMDR Format—Type
Selects the format of SMDR output.
Default
Ty p e  A
Value Range
Type A: 80 digits without call charge information 
Type B: 80 digits with call charge information 
Type C: 120 digits
Maintenance Console Location
2.16.1 [10-1] Main
Programming Manual References
None
Feature Manual References
1.16.1 SMDR (Station Message Detail Recording)
SMDR Format—Port
Selects the Serial Interface (RS-232C) port that is used to output the SMDR data.
Default
RS-232C 
Value Range
None, RS-232C
Maintenance Console Location
2.16.1 [10-1] Main
Programming Manual References
None 
						

							2.16 [10] Maintenance
418 PC Programming Manual
Feature Manual References
1.16.1 SMDR (Station Message Detail Recording)
SMDR Format—Page Length (Number of Lines)
Specifies the number of lines on a page of output paper. Match the SMDR output to the paper size 
being used in the printer.
Default
66
Value Range
4–99
Maintenance Console Location
2.16.1 [10-1] Main
Programming Manual References
None
Feature Manual References
1.16.1 SMDR (Station Message Detail Recording)
SMDR Format—Blank Footer Length (Number of Lines)
Specifies the number of lines to be skipped at the end of every page. The number of lines for the skip 
perforation should be shorter than the page length.
Default
0
Value Range
0–95
Maintenance Console Location
2.16.1 [10-1] Main
Programming Manual References
None
Feature Manual References
1.16.1 SMDR (Station Message Detail Recording)
SMDR Format—Date Format
Selects the printed date format. 
						

							2.16 [10] Maintenance
PC Programming Manual 419
Default
MM-DD-YY
Value Range
MM-DD-YY, DD-MM-YY, YY-MM-DD, YY-DD-MM
Maintenance Console Location
2.16.1 [10-1] Main
Programming Manual References
None
Feature Manual References
1.16.1 SMDR (Station Message Detail Recording)
SMDR Format—Time Format (12H / 24H)
Selects whether times are displayed using the 12- or 24-hour format.
Default
12H
Value Range
12H, 24H
Maintenance Console Location
2.16.1 [10-1] Main
Programming Manual References
None
Feature Manual References
1.16.1 SMDR (Station Message Detail Recording)
Print Information—Outgoing Call
Specifies whether the dialed digits of outgoing CO line calls are printed. Class of Service (COS) 
programming determines the printable records.
Default
Print
Value Range
No Print, Print
Maintenance Console Location
2.16.1 [10-1] Main 
						

							2.16 [10] Maintenance
420 PC Programming Manual
Programming Manual References
2.8.11 [2-7-1] Class of Service—COS Settings—CO & SMDR—Outgoing CO Call Printout (SMDR)
Feature Manual References
1.16.1 SMDR (Station Message Detail Recording)
Print Information—Incoming Call
Specifies whether the information relating to incoming CO line calls, such as callers identification 
name and number, is printed.
Default
No Print
Value Range
No Print, Print
Maintenance Console Location
2.16.1 [10-1] Main
Programming Manual References
None
Feature Manual References
1.16.1 SMDR (Station Message Detail Recording)
Print Information—Intercom Call
Specifies whether the dialed digits of outgoing intercom calls are printed.
Default
No Print
Value Range
No Print, Print
Maintenance Console Location
2.16.1 [10-1] Main
Programming Manual References
None
Feature Manual References
1.16.1 SMDR (Station Message Detail Recording)
Print Information—Log-in / Log-out
Specifies whether the log-in/log-out status is printed.