Panasonic Kx Taw848 PC Cprogramming Manual

							2.8 [2] System
PC Programming Manual 121
Value Range
1–600 s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
2.10.7 [4-1-6] Wired Extension—Simplified Voice Message
2.10.12 [4-2-4] Portable Station—Simplified Voice Message
Feature Manual References
1.16.5 SVM (Simplified Voice Message)
SVM—Dial Tone Continuous Time
Specifies the length of time that dial tone 3 is heard after all messages stored by the SVM feature for 
an extension are finished playing.
Default
5 s
Value Range
1–60 s
Maintenance Console Location
2.8.4 [2-3] Timers & Counters
Programming Manual References
2.10.7 [4-1-6] Wired Extension—Simplified Voice Message
2.10.12 [4-2-4] Portable Station—Simplified Voice Message
Feature Manual References
1.16.5 SVM (Simplified Voice Message)
2.8.5 [2-4] Week Table
A specific time mode (day, night, lunch, or break) can be selected for operation depending on the time 
of day. The time mode can be switched either automatically or manually. Select the desired switching 
mode from the Time Service Switching Mode option.
 
Time Table numbers correspond to tenant numbers (for example, Tenant 1 uses Time Table 1). Select 
the desired Time Table from the Time Table No. list.
 
When in Automatic Switching mode, the time modes of the tenant are switched as programmed in the 
corresponding Time Table. Manual switching is possible only from an authorized extension 
(determined by COS).
 To adjust the currently displayed Time Table, click and drag the divisions between two time 
periods. 
						

							2.8 [2] System
122 PC Programming Manual
 To program the time blocks of the currently displayed Time Table, including adding or 
deleting time blocks, click Time Setting.
2.8.6 [2-4] Week Table—Time Setting
The start times of 4 different time blocks can be programmed for each day of the week, for the 
selected Time Table, as well as the start and end times of up to 3 break periods.
1. Day/Lunch/Night—Day1 Start, Lunch Start, Day2 Start, Night Start—
Setting
Enables the setting of the start time for each time block.
Default
Day 1 Start, Night Start: Enable 
Lunch Start, Day 2 Start: Disable
Value Range
Disable, Enable
Maintenance Console Location
2.8.6 [2-4] Week Table—Time Setting
Programming Manual References
None
Feature Manual References
1.17.2 Tenant Service
1.17.4 Time Service
1. Day/Lunch/Night—Day1 Start, Lunch Start, Day2 Start, Night Start—Hour, 
Minute
Specifies the start time for each time block. Times can only be set when 1. Day/Lunch/Night—Day1 
Start, Lunch Start, Day2 Start, Night Start—Setting is set to Enable.
Default
Day1: 9:00 
Lunch: 12:00 
Day2: 13:00 
Night: 17:00
Value Range
00:00–23:59
Maintenance Console Location
2.8.6 [2-4] Week Table—Time Setting 
						

							2.8 [2] System
PC Programming Manual 123
Programming Manual References
None
Feature Manual References
1.17.2 Tenant Service
1.17.4 Time Service
2. Break—Break 1–3 Start—Setting
Enables the setting of the start time for each break period.
Default
Disable
Value Range
Disable, Enable
Maintenance Console Location
2.8.6 [2-4] Week Table—Time Setting
Programming Manual References
None
Feature Manual References
1.17.2 Tenant Service
1.17.4 Time Service
2. Break—Break 1–3 Start—Hour, Minute
Specifies the start time for each break period. Times can only be set when 2. Break—Break 1–3 
Start—Setting is set to Enable.
Default
00:00
Value Range
00:00–23:59
Maintenance Console Location
2.8.6 [2-4] Week Table—Time Setting
Programming Manual References
None
Feature Manual References
1.17.2 Tenant Service
1.17.4 Time Service 
						

							2.8 [2] System
124 PC Programming Manual
2. Break—Break 1–3 End—Hour, Minute
Specifies the end time for each break period. Times can only be set when 2. Break—Break 1–3 
Start—Setting is set to Enable.
Default
00:00
Value Range
00:00–23:59
Maintenance Console Location
2.8.6 [2-4] Week Table—Time Setting
Programming Manual References
None
Feature Manual References
1.17.2 Tenant Service
1.17.4 Time Service
2.8.7 [2-5] Holiday Table
A specific time mode (day, night, lunch, or break) can be selected for operation during holidays. Select 
the desired time mode from the Holiday Mode list.
 
The start and end dates of a maximum of 24 different holidays can be programmed.
Holiday Table—Setting
Enables the setting of the holiday.
Default
Disable
Value Range
Disable, Enable
Maintenance Console Location
2.8.7 [2-5] Holiday Table
Programming Manual References
None
Feature Manual References
1.17.4 Time Service 
						

							2.8 [2] System
PC Programming Manual 125
Holiday Table—Start Date—Month
Specifies the month of the holiday start date.
Default
1
Value Range
1–12
Maintenance Console Location
2.8.7 [2-5] Holiday Table
Programming Manual References
None
Feature Manual References
1.17.4 Time Service
Holiday Table—Start Date—Day
Specifies the day of the holiday start date.
Default
1
Value Range
1–31
Maintenance Console Location
2.8.7 [2-5] Holiday Table
Programming Manual References
None
Feature Manual References
1.17.4 Time Service
Holiday Table—End Date—Month
Specifies the month of the holiday end date.
Default
1
Value Range
1–12 
						

							2.8 [2] System
126 PC Programming Manual
Maintenance Console Location
2.8.7 [2-5] Holiday Table
Programming Manual References
None
Feature Manual References
1.17.4 Time Service
Holiday Table—End Date—Day
Specifies the day of the holiday end date.
Default
1
Value Range
1–31
Maintenance Console Location
2.8.7 [2-5] Holiday Table
Programming Manual References
None
Feature Manual References
1.17.4 Time Service
2.8.8 [2-6-1] Numbering Plan—Main
Details of the extension numbering schemes and feature access numbers can be programmed here. 
For more information on flexible numbering, see 1.6.4 Flexible Numbering/Fixed Numbering in the 
Feature Manual.
Extension
The leading numbers and the number of additional digits of the extension numbers for a maximum of 
64 different extension numbering schemes can be programmed.
Leading Number
Specifies the leading number of extension numbers and floating extension numbers.
Default
Extension Numbering Scheme 01: 1 
Extension Numbering Scheme 02: 2 
Extension Numbering Scheme 03: 3 
Extension Numbering Scheme 04: 4  
						

							2.8 [2] System
PC Programming Manual 127
Extension Numbering Scheme 21: 5 
Extension Numbering Scheme 22: 6 
Extension Numbering Scheme 05–20, 23–64: Not stored.
Value Range
Max. 2 digits (consisting of 0–9)
Maintenance Console Location
2.8.8 [2-6-1] Numbering Plan—Main
Programming Manual References
2.9.9 [3-5-1] Incoming Call Distribution Group—Group Settings
2.9.15 [3-7-2] VM(DPT) Group—Unit Settings
2.9.18 [3-8-2] VM(DTMF) Group—Group Settings
2.10.1 [4-1-1] Wired Extension—Extension Settings
2.10.8 [4-2-1] Portable Station—Extension Settings
2.11.4 [5-3-2] Voice Message—DISA Message
2.16.1 [10-1] Main
Feature Manual References
1.6.4 Flexible Numbering/Fixed Numbering
No. of Additional Digits
Specifies the number of additional digits following the leading number.
Default
XX
Value Range
None: 0 digit 
X: 1 digit 
XX: 2 digits
Maintenance Console Location
2.8.8 [2-6-1] Numbering Plan—Main
Programming Manual References
None
Feature Manual References
1.6.4 Flexible Numbering/Fixed Numbering
Features
Feature numbers to access various PBX features can be programmed. The following features are 
available while hearing a dial tone. 
						

							2.8 [2] System
128 PC Programming Manual
Operator Call
Specifies the feature number used to call the operator.
Default
0
Value Range
Max. 4 digits (consisting of 0–9, *, and #)
Maintenance Console Location
2.8.8 [2-6-1] Numbering Plan—Main
Programming Manual References
2.8.3 [2-2] Operator & BGM
2.12.6 [6-6] Tenant
Feature Manual References
1.12.3 Operator Features
Idle Line Access (Local Access)
Specifies the feature number used to make a CO line call by Idle Line Access (selects an idle CO line 
automatically).
Default
9
Value Range
Max. 4 digits (consisting of 0–9, *, and #)
Maintenance Console Location
2.8.8 [2-6-1] Numbering Plan—Main
Programming Manual References
2.9.2 [3-1-2] Trunk Group—Local Access Priority
Feature Manual References
1.3.11 CO Line Access
Trunk Group Access
Specifies the feature number used to make a CO line call using an idle CO line from a certain trunk 
group.
Default
8 
						

							2.8 [2] System
PC Programming Manual 129
Value Range
Max. 4 digits (consisting of 0–9, *, and #)
Maintenance Console Location
2.8.8 [2-6-1] Numbering Plan—Main
Programming Manual References
2.15.1 [9-1] CO Line Settings
Feature Manual References
1.3.11 CO Line Access
Redial
Specifies the feature number used to redial the last number dialed.
Default
#
Value Range
Max. 4 digits (consisting of 0–9, *, and #)
Maintenance Console Location
2.8.8 [2-6-1] Numbering Plan—Main
Programming Manual References
None
Feature Manual References
1.15.1 Redial, Last Number
System Speed Dialing / Personal Speed Dialing
Specifies the feature number used to make a call using a System/Personal Speed Dialing number.
Default
**
Value Range
Max. 4 digits (consisting of 0–9, *, and #)
Maintenance Console Location
2.8.8 [2-6-1] Numbering Plan—Main
Programming Manual References
2.10.3 [4-1-3] Wired Extension—Speed Dial
2.12.1 [6-1] System Speed Dial 
						

							2.8 [2] System
130 PC Programming Manual
Feature Manual References
1.16.3 Speed Dialing, Personal
1.16.4 Speed Dialing, System
Personal Speed Dialing - Programming
Specifies the feature number used to program Personal Speed Dialing numbers at an extension.
Default
*30 
Value Range
Max. 4 digits (consisting of 0–9, *, and #)
Maintenance Console Location
2.8.8 [2-6-1] Numbering Plan—Main
Programming Manual References
None
Feature Manual References
1.16.3 Speed Dialing, Personal
Doorphone Call
Specifies the feature number used to make a call to a doorphone.
Default
*31
Value Range
Max. 4 digits (consisting of 0–9, *, and #)
Maintenance Console Location
2.8.8 [2-6-1] Numbering Plan—Main
Programming Manual References
2.11.1 [5-1] Doorphone
Feature Manual References
1.4.10 Doorphone Call
Group Paging
Specifies the feature number used to page a certain paging group.
Default
*33