Panasonic Digital Imaging System For Copier Dp 6000 Operating Instructions

							4-4  Reducing/Enlarging the Length and Width (Independent X-Y%)49
Basic Features
4
Reducing/Enlarging the
Length and Width
(Independent X-Y%)
The Independent X-Y% feature allows you to make copies with independent
length or width of the original. There are three methods available.
Specifying X/Y Percentage Change (Variable X-Y%)
You can make copies of
the originals by
selecting different ratios
for X and Y.  The image
will be copied according
to your selected values.
Specifying Original/Copy Size (Calculator %)
Copies will be made
based on the ratios
calculated by the
machine from the input
measurements of the
document and the
desired copy.
Automatic X/Y Percentage Change (Auto-Fit)
The machine will make
copies of the originals
by calculating the X and
Y ratios so that the
image can fit onto the
selected paper size.
Y
X
You can enter a length (Y) between
1-999 mm in 1 mm increment.
The machine will automatically
adjust the ratio to 25% if the
calculated ratio is below 25%, and
400% if the calculated ratio is above
400%.
If you have also selected Auto
Center (Centre) for Image Shift,
then the image will be copied onto
the center of the paper as shown in
the diagram on the right.
You can select a ratio between 25-
400% in 1% increments.
When this is selected with Image
Rotation Off, the resulting output
will be as illustrated on the right. 
						

							4-4  Reducing/Enlarging the Length and Width (Independent X-Y%)50
Basic Features
4
You can make copies of your original by specifying its X and Y ratios
separately. The image will be copied according to the ratios that you have
entered.
Procedure
On the Basic Features screen, select Reduce/Enlarge.
Select Independent X-Y%.
Select Variable X-Y%.
The factory default for Reduce/
Enlarge is 100%.
Reduce/Enlarge can also be
selected on the Features Menu
screen.
The screen on the right has the Tray
6 (High Capacity Feeder), and
Finisher installed.
Select Cancel to cancel the settings.
Specifying X/Y Percentage Change (Variable X-Y%) 
						

							4-4  Reducing/Enlarging the Length and Width (Independent X-Y%)51
Basic Features
4
You can use         buttons below XY on
the display to increase or decrease the
ratio of X and Y simultaneously.
Select Cancel to cancel the settings.
Some features cannot be selected
together with this feature. See
Appendix B: Possible Combinations
of Features
 for details.
Enter the X and Y ratios by using         buttons.
For example, enter Y = 120% and X = 200%.
Load the original in the orientation of Head to Top, or Head to
Left.
Select the corresponding document orientation of the original
loaded.
Select Head to Top or Head to Left.
Select Save twice.
Select other features if necessary.
Enter the required number of sets by using the keypad and
press Start.
The copies are made according to the ratios specified in Step 4.
Chapter 3 Loading Documents for
information on how to load
documents.
Set the document orientation
correctly because if it is different
from the orientation of original
loaded, XY is different and their
reduction or enlargement becomes
different as a result.
See 
5-10: Selecting the Original
Orientation (Original Orientation) 
for
details. 
						

							4-4  Reducing/Enlarging the Length and Width (Independent X-Y%)52
Basic Features
4
Select Cancel to cancel the settings.
The machine will automatically
adjust the ratio to 25% if the
calculated ratio is 25% or below, and
400% if the calculated ratio is 400%
and above.
The factory default for Reduce/
Enlarge is 100%.
Reduce/Enlarge can also be
selected on the Features Menu
screen.
The screen on the right has the Tray
6 (High Capacity Feeder), and
Finisher installed.
The machine will make copies of your original based on the ratios calculated
from the measurements of the original and the copy that you have entered.
Procedure
On the Basic Features screen, select Reduce/Enlarge.
Select Independent X-Y%.
Select Calculator %.
Specifying Original/Copy Size (Calculator %) 
						

							4-4  Reducing/Enlarging the Length and Width (Independent X-Y%)53
Basic Features
4
Use the ruler markings surrounding
the Document Glass to set the area
of the original for scanning.
Select Cancel to cancel the settings.
To change the value, select Enter/
Next to move to the value you want.
Chapter 3 Loading Documents for
information on how to load
documents.
Set the document orientation
correctly because if it is different
from the orientation of original
loaded, XY is different and their
reduction or enlargement becomes
different as a result.
See
 5-10: Selecting the Original
Orientation (Original Orientation)
 for
details.
You cannot select Save until you
have entered all the measurements
for the document and paper size.
Some features cannot be selected
together with this feature. See
Appendix B: Possible Combinations
of Features
 for details.
Check that there is a  button on the left of Original Size under
Y. Enter the length of the document by using the keypad.
For example, enter 210 mm.
Select Enter/Next.
The   button moves to the left of Copy Size under Y.
Select the value of X in the same way as explained from Steps
5 to 6.
The machine calculates the XY ratio and it is displayed.
Load the original in the orientation of Head to Top, or Head to
Left.
Select the corresponding document orientation of the original
loaded.
Select Head to Top or Head to Left.
Select Save twice.
Select other features if necessary.
Enter the required number of sets by using the keypad and
press Start.
The copies are made according to the specified copy sizes. 
						

							4-4  Reducing/Enlarging the Length and Width (Independent X-Y%)54
Basic Features
4
The factory default for Reduce/
Enlarge is 100%.
Reduce/Enlarge can also be
selected on the Features Menu
screen.
Paper Supply can also be selected
on the Features Menu screen.
The screen on the right has the Tray
6 (High Capacity Feeder), and
Finisher installed.
Select Cancel to cancel the settings.
The machine will make copies of your original by calculating the X and Y
ratios so that the image can fit onto the selected paper size.
Procedure
On the Basic Features screen, select the tray with the desired
paper size in Paper Supply.
For example, select 4.
On the Basic Features screen, select Reduce/Enlarge.
Select Independent X-Y%.
Automatic X/Y Percentage Change (Auto-Fit) 
						

							4-4  Reducing/Enlarging the Length and Width (Independent X-Y%)55
Basic Features
4
To disable Image Rotation, set it to
Off on the Customized Features
screen or Features Menu screen.
Some features cannot be selected
together with this feature. See
Appendix B: Possible Combinations
of Features
 for details.
Select Cancel to cancel the settings.
Chapter 3 Loading Documents for
information on how to load
documents.
Select Auto-Fit.
Load the original in the orientation of Head to Top, or Head to
Left.
Select the corresponding document orientation of the original
loaded.
Select Head to Top or Head to Left.
Select Save twice.
Select other features if necessary.
Enter the required number of sets by using the keypad and
press Start.
The copies are made by enlarging or reducing the original image size so that it
fits onto the selected paper size.
Automatic Image Rotation
When the document orientation of the original and paper loaded differs,
the image will be copied by rotating it so that they are the same.
(Factory default: Image Rotation is On.)  To copy a portrait original in
landscape orientation, select rotation to be off so that the desired
alteration to XY ratio is achieved.
5-11: Rotating and Copying in
Different Directions (Image Rotation) 
						

							4-5  Copying on One Side (2 Sided)56
Basic Features
4
Copying on One Side
(2 Sided)
The 2 Sided feature allows you to make one sided copies from one sided
documents or two sided documents,
To make one sided copies from a two sided document, use the DADF.
Procedure
On the Basic Features screen, select 2 Sided.
The screen on the right has the Tray
6 (High Capacity Feeder), and
Finisher installed.
2 Sided can also be selected on the
Features Menu screen. 
						

							4-5  Copying on One Side (2 Sided)57
Basic Features
4
Select either 1     1 Sided or 2     1 Sided.
For example, select 2     1 Sided.
Select Head to Head or Head to Toe as the image orientation
of the document if you have selected 2     1 Sided.
Head to Head  When all sides of a document have the same orientation.
Head to Toe When the orientation of side two is the reverse of side one.
The factory default is 1     1 Sided.
Select Cancel to cancel the settings.
Select Cancel to cancel the settings.
When making two sided copies, use
the DADF.  The Document Glass
can only be used for making one
sided copies. 
						

							4-5  Copying on One Side (2 Sided)58
Basic Features
4
Some features cannot be selected
together with this feature. See
Appendix B: Possible Combinations
of Features 
for details.
5-10: Selecting the Original
Orientation (Original Orientation)
 for
details.
Chapter 3 Loading Documents for
information on how to load
documents.
For 2     1 Sided copying, use the
DADF.
 Load the original in the orientation of Head to Top, or Head to
Left.
Select the corresponding document orientation of the original
loaded.
Select Head to Top or Head to Left.
Select Save.
Select other features if necessary.
Enter the required number of sets by using the keypad and
press Start.
The copies are made on one side of the paper.