Panasonic Digital Imaging System For Copier Dp 6000 Operating Instructions

							6-3  Configuring the Machine with Tools Mode149
Custom Presets
6
Configuring the Machine with
Tools Mode
This section uses the three examples described below to explain the
procedures for configuring Tools Mode.
¥ Selecting the feature defaults
¥ Changing the Access Number of the administrator
¥ Configuring a screen (default/basic/customized)
Selecting the Feature Defaults
This section describes the procedures for selecting the feature defaults.
The example here is to change the default copy density to Darkest.
Procedure
Procedure
Press Settings/Meter Check.
Select Tools Mode.
The screen on the right is when the
Auditron feature is enabled.  See
Chapter 9 Using the Auditron
Feature
 for details. 
						

							6-3  Configuring the Machine with Tools Mode150
Custom Presets
6
Enter the Access Number of the System Administrator and
select Confirm.
Each input digit is represented by an asterisk.
Select Feature Defaults.
Use     to select Lighter/Darker.
 Select Change Settings.
You can also select Lighter/Darker
directly by touching it.
The factory default of the access
number is 11111  .
For models with the printer feature,
the screen displayed differs. 
						

							6-3  Configuring the Machine with Tools Mode151
Custom Presets
6
Select the default value of Lighter/Darker.
For example, select Darkest.
Select Save.
Select Close until the screen shown in Step 4 is displayed.
Select Exit Tools.
The default value of Lighter/Darker is set. 
						

							6-3  Configuring the Machine with Tools Mode152
Custom Presets
6
This section explains the procedures for changing the Access Number of the
administrator. The factory default is 11111.
If you have changed the Access Number, make sure that you keep a record
of the new number.
Procedure
Press Settings/Meter Check.
Select Tools Mode.
Enter the Access Number of the System Administrator and
select Confirm.
Each input digit is represented by an asterisk.
Changing the Access Number of the Administrator
The screen on the right is when the
Auditron feature is enabled.  See
Chapter 9 Using the Auditron
Feature
 for details. 
						

							6-3  Configuring the Machine with Tools Mode153
Custom Presets
6
Select Change of Access Number.
Enter the New Access Number by using the keypad. You can
enter between 4 to 12 digits. Then select Enter.
Enter the Access Number again, and select Enter.
Select Close until the screen shown in Step 4 is displayed.
Select Exit Tools.
The New Access Number of the System Administrator becomes valid.
If you made a mistake while entering
the Access Number, press the Clear
C button to clear and re-enter.
To reset the Access Number setting,
press Reset.
For models with the printer feature,
the screen displayed differs. 
						

							6-3  Configuring the Machine with Tools Mode154
Custom Presets
6
This section explains the procedures for changing the default screen, and
customizing the Basic Features screen and the Customized Features
screen.
    Changing the Default Screen  
This feature allows you to display the desired screen when the power is
switched on, when it returns to the ready mode from the power saver
mode, or when Clear All is pressed.
The factory default screen is the Basic Features screen.
Procedure
Press Settings/Meter Check.
Select Tools Mode.
Enter the Access Number of the System Administrator and
select Confirm.
Each input digit is represented by an asterisk.
The screen on the right is displayed
when the Auditron feature is
enabled.  See 
Chapter 9 Using the
Auditron Feature
 for details.
The factory default of the Access
Number is 11111.
Configuring a Screen (Default/Basic/Customized) 
						

							6-3  Configuring the Machine with Tools Mode155
Custom Presets
6
Select Screen Layout.
Select Change Settings in Default Screen.
 Select Change Settings.
Select the screen to be displayed as the default screen and
select Save.
For example, select Customized Features.
For models with the printer feature,
the screen displayed differs. 
						

							6-3  Configuring the Machine with Tools Mode156
Custom Presets
6
Then select Close until the screen shown in Step 4 is
displayed.
Select Exit Tools.
The new default screen is defined.
    Configuring the Basic Features Screen  
This feature allows you to select the number of features to be displayed
on the Basic Features screen and which features to be displayed on
these basic buttons.
¥ Display 2 Features
Assign the features to the two buttons (Feature Buttons 1 and 2)
¥ Display 3 Features
Assign the features to Feature Button 1, Feature Button 2 and Feature
Button 3.
¥ Display 4 Features
Assign the features to Feature Button 1, Feature Button 2, Feature
Button 3 and Feature Button 4.
Procedure
Press Settings/Meter Check.
Select Tools Mode.
Basic Features screen can display a
maximum of four feature buttons.
You can select to display two, three
or four features in the layouts shown
below.
The factory default is Display 3
Features.
The screen on the right is when the
Auditron feature is enabled.  See
Chapter 9 Using the Auditron
Feature
 for details. 
						

							6-3  Configuring the Machine with Tools Mode157
Custom Presets
6
Enter the Access Number of the System Administrator and
select Confirm.
Each input digit is represented by an asterisk.
Select Screen Layout.
Select the number of features to be displayed on the Basic
Features screen and select Change Settings.
For example, select Display 4 Features.
The factory default of the access
number is 11111  .
For models with the printer feature,
the screen displayed differs. 
						

							6-3  Configuring the Machine with Tools Mode158
Custom Presets
6
Use the         buttons to select the desired basic button.
 Select Change Settings.
Select the feature to be displayed in the selected basic button
and select Save.
For example, select Original Type.
Repeat Steps 6 to 8 when necessary to assign the required
features to all the basic buttons.
Select Close until the screen shown in Step 4 is displayed.
 Select Exit Tools.
You can also select the basic button
directly by touching it.
The buttons are displayed on two
pages. Use     or      buttons to page
up or page down.
Select No Feature if you do not wish to
assign any feature to the button.
Buttons that are unavailable are dim
and grey in color.
The screen on the right has the
Finisher installed.