Oce ColorWave 600 User Manual
Have a look at the manual Oce ColorWave 600 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 5 Oce manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 37
Finishing
The finishing options
Introduction
The Océ ColorWave 600 is delivered with a 'Top delivery tray' to collect your printed
output. The
'Top delivery tray' can collect 50 - 100 plain paper prints with a maximum length
of
48" [1200mm].
Note:
The media type you use influences the output capacity. In the Océ Express WebTools you
can define the default 'Delivery destination' for your
printed output. • If you
select
'Top delivery tray' your printed output is by...](http://img.usermanuals.tech/thumb/3543/37514/w64_Oce_ColorWave_600-36.png "Page 37
Finishing
The finishing options
Introduction
The Océ ColorWave 600 is delivered with a 'Top delivery tray' to collect your printed
output. The
'Top delivery tray' can collect 50 - 100 plain paper prints with a maximum length
of
48\" [1200mm].
Note:
The media type you use influences the output capacity. In the Océ Express WebTools you
can define the default 'Delivery destination' for your
printed output. • If you
select
'Top delivery tray' your printed output is by...")
![Page 46
Note:
Be aware of the printer working area. (see ‘Printer working area [Footprint]’ on page 23) #
Illustration
Action Use
both hands to pull at the
'Lower left cover'. Remove the
'Lower left
cover'.
1 Pull
at the Foot cover. Remove
the 'Foot'
cover.
2 Push
the handle [1]. The 'Foot'
snaps up [2].
3
Repeat
action 1
till 3 on the
'Lower right
cover' 4
Chapter 3
- Prepare the printing system for use and get started46How to move the Océ ColorWave 600...](http://img.usermanuals.tech/thumb/3543/37514/w64_Oce_ColorWave_600-45.png "Page 46
Note:
Be aware of the printer working area. (see ‘Printer working area [Footprint]’ on page 23) #
Illustration
Action Use
both hands to pull at the
'Lower left cover'. Remove the
'Lower left
cover'.
1 Pull
at the Foot cover. Remove
the 'Foot'
cover.
2 Push
the handle [1]. The 'Foot'
snaps up [2].
3
Repeat
action 1
till 3 on the
'Lower right
cover' 4
Chapter 3
- Prepare the printing system for use and get started46How to move the Océ ColorWave 600...")
Set the 'Océ Finishing Assistant' Introduction This setting is only available when the 'Configuration' - 'Printer setup' - 'Finishing' - 'Finisher configuration type' setting is set to 'Estefold'. The 'Océ Finishing Assistant' can automatically detect the legend (if present) of a drawing and rotate and align the drawing so the legend will be on the cover page of the fold package. If no legend can be detected the print is delivered unfolded. When enabled, the 'Océ Finishing Assistant' overrules the default rotation and alignment settings for folded output. Before you begin This setting is editable for the Key operator or Power user. How to set the 'Océ Finishing Assistant' 1. Click 'Preferences' - 'Print job defaults' - 'Layout'. 2. Click 'Edit' in the 'Layout' bar or click the value of the 'Océ Finishing Assistant' setting. 3. Select 'Enabled' if the printer must automatically detect the legend of your drawings and fold the drawings correctly. 4. Click 'Ok' to confirm your entries or 'Cancel' to reject your entries. Chapter 2 - Get to know the printing system 41Set the 'Océ Finishing Assistant' Downloaded From ManualsPrinter.com Manuals
Chapter 2 - Get to know the printing system42Set the 'Océ Finishing Assistant' Downloaded From ManualsPrinter.com Manuals
Chapter 3 Prepare the printing sys- tem for use and get start- ed Downloaded From ManualsPrinter.com Manuals
Introduction This chapter contains all the information you need to prepare your Océ ColorWave 600 for use. You can learn more about the following. • How to move the printer. • How to connect the power supply cable and the network cable. • How to run the installation procedure. • How to (re)load the toner cartridges. • How to (re)place the maintenance tray. • How to (re)load a media roll. • How to complete the printer configuration in the Océ Express WebTools. • How to configure the regional settings of the Océ ColorWave 600. • How to print the Customer Acceptance Test. Chapter 3 - Prepare the printing system for use and get started44Introduction Downloaded From ManualsPrinter.com Manuals
How to move the Océ ColorWave 600 IntroductionAttention: If connected you must first switch off and disconnect the Océ ColorWave 600. (see ‘Switch on or switch off the printer’ on page 172) Attention: Close the media drawers. Chapter 3 - Prepare the printing system for use and get started 45How to move the Océ ColorWave 600 Downloaded From ManualsPrinter.com Manuals
Note: Be aware of the printer working area. (see ‘Printer working area [Footprint]’ on page 23) # Illustration Action Use both hands to pull at the 'Lower left cover'. Remove the 'Lower left cover'. 1 Pull at the Foot cover. Remove the 'Foot' cover. 2 Push the handle [1]. The 'Foot' snaps up [2]. 3 Repeat action 1 till 3 on the 'Lower right cover' 4 Chapter 3 - Prepare the printing system for use and get started46How to move the Océ ColorWave 600 Downloaded From ManualsPrinter.com Manuals
Illustration Action Move the Océ ColorWave 600 printer. Note: Be aware of the printer working area. 5 Pull out the left 'Foot' [1] until it touches the ground and locks [2]. You should hear a click as it locks. Note: If you do not hear a click, place your foot on the foot of the printer [1] and at the same time push gently against the printer until you hear the click. 6 Pin:Replace the 'Foot' covers. Place the pin into the notch. 7a Chapter 3 - Prepare the printing system for use and get started 47How to move the Océ ColorWave 600 Downloaded From ManualsPrinter.com Manuals
Illustration Action Notch:7b 7c Pin:Replace the 'Lower left cover'. Place the pin into the notch. 8a Chapter 3 - Prepare the printing system for use and get started48How to move the Océ ColorWave 600 Downloaded From ManualsPrinter.com Manuals
Illustration Action Notch:8b 8c Repeat action 6 till 8 at the right hand side. Replace the 'Lower right cover' 9 Chapter 3 - Prepare the printing system for use and get started 49How to move the Océ ColorWave 600 Downloaded From ManualsPrinter.com Manuals
Connect the Océ ColorWave 600 printer How to connect the network cable # Illustration Action Remove the cover of the 'Con- nection panel' at the rear side of the printer. 1 Lead the connection cable through the cover. 2 Connect one side of the data ca- ble (UTP cable with a RJ45 connector) to the indicated net- work connection on the connec- tion panel of the 'Océ PowerM controller'. Connect the other side of the network cable to your company network. 3 Chapter 3 - Prepare the printing system for use and get started50How to connect the network cable Downloaded From ManualsPrinter.com Manuals