Oce ColorWave 600 User Manual

							The printer operator panel
The hardware of the Printer operator panel
Illustration
Component - function table
#
Description / Function
Component
Nr
Keys with the numeric values 0-9 in the lower
part of the 'Printer operator panel', that allow
the operator to enter a numeric value, for ex-
ample the number of prints.
'Numeric keys'
1
Key 
that allows the operator to select the op-
tion 
displayed in lower left corner of the screen
of the 'Printer operator panel'.
'Lower left

 softkey'
2
(see 
‘The main screens on the printer operator
panel’  
on page 34)
'Screen' 3
Chapter 2
 - Get to know the printing system 31The hardware of the Printer operator panel
Downloaded From ManualsPrinter.com Manuals 
						

							Description / Function
Component
Nr
The status light indicates the status of the
printer. • A green
 light indicates that the printer is
ready.
• A blinking

 green light indicates that the
printer

 is busy.
• A red light can 
indicate the following.
–
 the printer is calibrating
–
 the printer is not ready
–
 an error occurred
• A blinking red light indicates that the
printer

 is busy and an error occurred.
'Status 
light'
4
Key 
that allows the operator to select the op-
tion 
displayed in upper left corner of the
screen 
of the 'Printer operator panel'.
'Upper left
 softkey'
5
Key 
that allows the operator to select the op-
tion 
displayed in upper right corner of the
screen 
of the 'Printer operator panel'.
'Upper right
 softkey'
6
Key 
that offers functionality that is compara-
ble 
to left-mouse-button functionality. If the
operator presses
 this key, the user interface
object that

 has the focus is opened, executed
or confirmed.
The 
 operator can use this button (for example)
to 
do the following.
• open 
a setting
• close and
 confirm the selected value of a
setting
• change the

 value of a setting
• start 
a wizard
'Confirmation 
key'
7
Wheel on the right side of the printer operator
panel, that allows the operator to• scroll through

 the screen
• scroll through

 settings values
'Scroll 
wheel'
8
Key 
that allows the operator to select the op-
tion 
displayed in lower right corner of the
screen 
of the 'Printer operator panel'.
'Lower right
 softkey' 9
Chapter 2
 - Get to know the printing system32The hardware of the Printer operator panel
Downloaded From ManualsPrinter.com Manuals 
						

							Description / Function
Component
Nr
The green key on the printer operator panel
that 
allows the operator to start a print job
from 
the 'Queue' or a 'Smart Inbox'.
'Green start
 key'
10
The
 
red key on the 'Printer operator panel'
that 
allows the operator to immediately stop
the print
 job that is currently printed.
'Red 
stop key' 11 /
B Chapter 2
 - Get to know the printing system 33The hardware of the Printer operator panel
Downloaded From ManualsPrinter.com Manuals 
						

							The main screens on the printer operator panel
#
Function
Screen
The 'Home' screen is the basic screen that displays only the
most relevant information: the condition of the system and
what it is doing now.
Tasks (performed by 'Any user'):
• Monitor
 the system status.
Note:
The information in the 'Home' screen is equivalent to
the system messages displayed in the 'System' tab of the
'Océ 
EWT'. The 'Smart Inbox' screen displays your jobs at the printer.
You can create print jobs from here. If necessary, you can
change 

the job settings and print a job again.
Tasks (performed by 'Any user'): • Control

 your jobs 
at the printer - find your jobs, make set-
tings, start jobs.
• Create

 jobs at the printer - print jobs that have been sent to
the 'Smart Inbox'.
• Create jobs

 
at the printer - reprint jobs that have been
printed before.
Note:
The 'Smart Inbox' screen is equivalent to the 'Smart
Inbox' pane
 in 
the 'Jobs' tab of the 'Océ EWT'. Chapter 2
 - Get to know the printing system34The main screens on the printer operator panel
Downloaded From ManualsPrinter.com Manuals 
						

							Function
Screen
The 'Queue' screen allows you to monitor and control the
progress of print jobs.
Tasks (performed by 'Any user'):
• Monitor
 print jobs - what is the progress (= the 'Queue'
pane). (see

 ‘The 
job states’  on page 213)
• Solve
 problems with jobs 
- media requests.
• Pause and
 resume print jobs.
Note:
The 'Queue' screen is partly equivalent to the 'Queue'
pane 
in the 'Jobs' tab of the 'Océ EWT'. The 'System' screen is your view on the system.
Tasks 
(performed by 'Any user'):
• Monitor
 toner status.
• Monitor the

 available media on the printer.
Note:
The 'System' screen is equivalent to the 'System' tab of
the 'Océ EWT'. Chapter 2
 - Get to know the printing system 35The main screens on the printer operator panel
Downloaded From ManualsPrinter.com Manuals 
						

							Function
Screen
The 'Maintenance' screen allows you to perform mainte-
nance tasks and troubleshooting tasks.
Tasks (performed by 'Any user', but most likely by the 'Key
operator') to
 solve 
problems with the printer:
• 'Calibration'
'Calibrate the
 printer'
• - 'Clear

 system'
'Remove
  all jobs from 
system'
• 'Demo 
print'
'Print a demo image':
–'Demoprint Economy
  Mode'
–'Demoprint Presentation
  Mode'
–'Demoprint Production

 Mode'
–'Quality 
Reference Chart'
–'Customer 
Analysis Tool'
• Usage counters
 (counters, 'TAC' readings).
Note:
The 'TAC' is a click that is a function of print volume
(square meter) and of toner coverage (grams /square
meter). The 'Configuration' screen allows you to configure the
printer.
Tasks 
(performed by the 'System administrator'):
• Configure the
 system (install, network configuration).
• Set

 
the preferred language.
• Monitor the
 software version. Chapter 2
 - Get to know the printing system36The main screens on the printer operator panel
Downloaded From ManualsPrinter.com Manuals 
						

							Finishing
The finishing options
Introduction
The Océ ColorWave 600 is delivered with a 'Top delivery tray' to collect your printed
output. The 
'Top delivery tray' can collect 50 - 100 plain paper prints with a maximum length
of
 48" [1200mm].
Note:
The media type you use influences the output capacity. In the Océ Express WebTools you 
can define the default 'Delivery destination' for your
printed output. • If you

 select 
'Top delivery tray' your printed output is by default delivered in the
standard
 'Top delivery tray'.
• If you select 
'External output (back)' your printed output is by default delivered at
the back
 of the printer. In that case 
you could expand your printer with one of the
following finishing
 options.
Attention:
If you use 2 inch media cores instead of the standard 3 inch media cores, the printed
output 
is automatically delivered at the back of the printer. The installation of one of the
finishing options is then advised. Chapter 2
 - Get to know the printing system 37The finishing options
Downloaded From ManualsPrinter.com Manuals 
						

							The finishing options
#
Illustration
'Receiving rack (basket)' The 'Receiving rack (basket)' is hooked
at 
the rear side of the printer. It can
collect
 2 - 5 prints. The 'Receiving rack
(basket)' 

bends the printed output. Not
all media types are 
appropriate for this
finishing option.
Note:
The 'Receiving rack (basket)' is
not 
supported in combination
with
 the folder or Copy delivery
tray. #
Illustration
Folder The 
folder is an automatic folder that
folds large
 
sized plots.
Note:
The folder is not supported in
combination with
 the 'Receiv-
ing 

rack (basket)' or Copy deliv-
ery 
tray.
Note:
If you use a folder you must set
the folder value. (see  ‘Define the
folder 
value’  on page 40) Chapter 2
 - Get to know the printing system38The finishing options
Downloaded From ManualsPrinter.com Manuals 
						

							#
Illustration
Copy delivery tray The Copy delivery tray is a flat tray be-
hind the printer. The Copy delivery tray
can collect a maximum of 100 prints.
Note:
The folder is not supported in
combination with
 the 'Receiv-
ing rack

 (basket)' or folder. Chapter 2
 - Get to know the printing system 39The finishing options
Downloaded From ManualsPrinter.com Manuals 
						

							Define the folder value
Introduction
If you use a folder you must set the folder value.
Attention:
Please do not change the 'Configuration' - 'Printer setup' - 'Finishing' - 'Model name
(configType)' setting.
 This setting is intended for service purposes 
only. How to define the folder value
Attention:
Access the Océ Express WebTools. This setting is editable for the System administrator
the Power
 user. 1.
Navigate 
to 'Configuration' - 'Printer setup' - 'Finishing'.
2. Set 
the value to 'Estefold' if a folder is connected to the external output at the rear side
of
 the printer.
The 

default folder value is 'No finisher'. You must only change this value if your hardware
configuration changes.
3. Click 
'Ok' to confirm your entries or 'Cancel' to reject your entries.
Chapter 2
 - Get to know the printing system40Define the folder value
Downloaded From ManualsPrinter.com Manuals