Oce ColorWave 600 User Manual
Have a look at the manual Oce ColorWave 600 User Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 5 Oce manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
![Page 172
Control the printer
Switch on or switch off the printer
How to switch on or switch off the printer
#
Illustration
On / off switch.
'On / Off switch' [19]The 'On / Off switch' at the front side of
the printer.
Use
this switch in your daily work to
switch
on and switch off the printer. The green main power switch at the rear
side
of the printer.
Use
this switch only if you must connect
or disconnect the mains supply of the
printer.
To disconnect
the mains supply:
• Use
the green...](http://img.usermanuals.tech/thumb/3543/37514/w64_Oce_ColorWave_600-171.png "Page 172
Control the printer
Switch on or switch off the printer
How to switch on or switch off the printer
#
Illustration
On / off switch.
'On / Off switch' [19]The 'On / Off switch' at the front side of
the printer.
Use
this switch in your daily work to
switch
on and switch off the printer. The green main power switch at the rear
side
of the printer.
Use
this switch only if you must connect
or disconnect the mains supply of the
printer.
To disconnect
the mains supply:
• Use
the green...")
![Page 176
Position of the component
Displayed warning
'Front cover' [6]
Note:
Normally you open the front cover in case
of a media jam. 'Top cover' [14]
Note:
Normally you open the top cover in case
of
a media jam, to
check the guide flap
(see
‘Check and clean the guide flap’ on
page 184
) or to check the print surface (see
‘Check and clean the print surface’ on page
181
). Chapter 5
- Use the printing system176Cover or door opened
Downloaded From ManualsPrinter.com Manuals
6
14](http://img.usermanuals.tech/thumb/3543/37514/w64_Oce_ColorWave_600-175.png "Page 176
Position of the component
Displayed warning
'Front cover' [6]
Note:
Normally you open the front cover in case
of a media jam. 'Top cover' [14]
Note:
Normally you open the top cover in case
of
a media jam, to
check the guide flap
(see
‘Check and clean the guide flap’ on
page 184
) or to check the print surface (see
‘Check and clean the print surface’ on page
181
). Chapter 5
- Use the printing system176Cover or door opened
Downloaded From ManualsPrinter.com Manuals
6
14")
The toner states # Description Icon Toner OK Toner low, empty or cartridge not present. Chapter 5 - Use the printing system 171The system monitor and the system states Downloaded From ManualsPrinter.com Manuals
Control the printer Switch on or switch off the printer How to switch on or switch off the printer # Illustration On / off switch. 'On / Off switch' [19]The 'On / Off switch' at the front side of the printer. Use this switch in your daily work to switch on and switch off the printer. The green main power switch at the rear side of the printer. Use this switch only if you must connect or disconnect the mains supply of the printer. To disconnect the mains supply: • Use the green main power switch to switch off the printer. • Disconnect the mains supply cable. To connect the mains supply: • Connect the mains supply cable. • Use the green main power switch to switch on the printer. Chapter 5 - Use the printing system172Switch on or switch off the printer Downloaded From ManualsPrinter.com Manuals 19
Pause or resume the printer Introduction If you do not want the printer to start printing you can pause the printer. If the printer can start printing again you can resume the printer. How to 'Pause' or 'Resume' the printer # Remarks Action To pause the printer: In the 'Queue' screen use the 'Lower left softkey' key on the printer operator panel to pause the printer. The following message is displayed. • 'Printer pause requested' • 'The printer stops after this page', if the printer was busy printing. In the 'Queue' screen use the 'Lower right softkey' to 'Re- sume' the printer. Chapter 5 - Use the printing system 173Pause or resume the printer Downloaded From ManualsPrinter.com Manuals
Solve problems with the printer Introduction Introduction If there is a problem with the printer that the operator can solve, the printer operator panel displays the following message. Please follow the instructions on the printer operator panel step by step. For additional information about some instructions or the location of specific covers or doors, please refer to the following modules: • ‘Cover or door opened’ on page 175. • ‘Pull up the 'Top delivery tray' and open the 'Top cover'’ on page 178. • ‘Close the 'Top cover' and flap back the 'Top delivery tray'’ on page 180. • ‘Cut the media’ on page 190 Chapter 5 - Use the printing system174Introduction Downloaded From ManualsPrinter.com Manuals
Cover or door opened Introduction The media drawers and certain covers must only be opened if you are asked to do so in a wizard on the printer operator panel. Attention: When you open one of the indicated covers or drawers while you are not in a wizard, the system produces a warning signal. The red LED on the printer operator panel illuminates. Attention: When you open one of these covers or drawers during printing, the printer stops and the printer operator panel shows one of the warnings that are listed in the table below. When you have closed the indicated cover or drawer, the print is cut and the print job is sent to printer again. # Position of the component Displayed warning 'Media drawer' [2, 3, 4] Note: Normally you open a media drawer to load or replace a media roll or in case of a media jam. Chapter 5 - Use the printing system 175Cover or door opened Downloaded From ManualsPrinter.com Manuals 24 3
Position of the component Displayed warning 'Front cover' [6] Note: Normally you open the front cover in case of a media jam. 'Top cover' [14] Note: Normally you open the top cover in case of a media jam, to check the guide flap (see ‘Check and clean the guide flap’ on page 184 ) or to check the print surface (see ‘Check and clean the print surface’ on page 181 ). Chapter 5 - Use the printing system176Cover or door opened Downloaded From ManualsPrinter.com Manuals 6 14
Position of the component Displayed warning 'Top back cover' [9]Note: Normally you open the top back cover in case of a media jam. Chapter 5 - Use the printing system 177Cover or door opened Downloaded From ManualsPrinter.com Manuals 9
Pull up the 'Top delivery tray' and open the 'Top cover' How to pull up the 'Top delivery tray' and open the 'Top cover' # Illustration Action Pull up the left part of the top delivery tray. 1 Lock the left part of the top de- livery tray with the metal locking mechanism. Repeat step 1 and 2 for the right part of the top delivery tray. 2 Open the 'Top cover'.3 Chapter 5 - Use the printing system178Pull up the 'Top delivery tray' and open the 'Top cover' Downloaded From ManualsPrinter.com Manuals
Illustration Action ‘Check and clean the print surface’ on page 181 [1] or ‘Check and clean the guide flap’ on page 184 [2]. 4 Chapter 5 - Use the printing system 179Pull up the 'Top delivery tray' and open the 'Top cover' Downloaded From ManualsPrinter.com Manuals
Close the 'Top cover' and flap back the 'Top delivery tray' If you are ready # Illustration Action Close the 'Top cover'. 1 Unlock the metal locking mech- anisms of the left and the right part of the top delivery tray. 2 Flap back the left part and the right part of the top delivery. Note: If the left part and the right part of the top de- livery tray are not in the same position, you can adjust the top delivery tray. (see ‘Adjust the 'Top delivery tray'’ on page 187 ) 3 Chapter 5 - Use the printing system180Close the 'Top cover' and flap back the 'Top delivery tray' Downloaded From ManualsPrinter.com Manuals