Oce ColorWave 600 User Manual

							Configure the 'Media request time-out'
Introduction
The printer operator panel displays a media request when a media is requested that is not
available on the printer.• When the
 'Media request time-out' setting is disabled, the media request will be dis-
played 
on the printer operator panel until it is resolved.
• When 
the 'Media request time-out' setting is enabled (default), you can enter a media
request time-out value in seconds. If the media request is not resolved within the media
request time-out period, the 'Action after media request time-out' setting determines
if the printer either deletes the job from the job queue or puts the job in attention
state.
When

 to do Enable the 'Media request time-out' setting if print productivity is an important factor.
How 

to configure the 'Media request time-out' 1. Click 'Preferences' - 'System properties'.
2. Click 
'Edit' in the 'Printer properties' bar or click the value of the 'Media request time-
out' 
setting.
3. When you enable the setting, you must enter a time period as well. If you choose to disable
the setting, the time period will not 
be adjustable.
4. Click 
'Ok' to confirm your entries or 'Cancel' to reject your entries.
How
 to configure the 'Action after media request time-out' 1. Click 
'Preferences' - 'System properties'.
2. Click 
'Edit' in the 'Printer properties' bar or click the value of the 'Action after media
request time-out'
 
setting.
3. Click 
'Put the job on attention state' or 'Delete the job'.
4. Click 
'Ok' to confirm your entries or 'Cancel' to reject your entries.
Chapter 4
 - Configure the printing system 121Configure the 'Media request time-out'
Downloaded From ManualsPrinter.com Manuals 
						

							Configure the 'Printer panel time-out'
Introduction
The printer operator panel can automatically return to the Home screen. When this setting
is disabled, the panel never returns to the Home screen automatically.Note:
When enabled, the printer operator panel returns to the Home screen when the keys
and the
 scroll wheel are 
not activated during the specified time-out period. When to do
Enable the setting and define a suitable time-out period that does not interfere 
with the
print productivity.
How 

to configure the 'Printer panel time-out' 1. Click 'Preferences' - 'System properties'.
2. Click 
'Edit' in the 'Printer properties' bar or click the value of the 'Printer panel time-
out' 
setting.
3. When you enable the setting, you must enter a time period as well. If you choose to disable
the setting, the time-out period will not 
be adjustable.
4. Click 
'Ok' to confirm your entries or 'Cancel' to reject your entries.
Chapter 4
 - Configure the printing system122Configure the 'Printer panel time-out'
Downloaded From ManualsPrinter.com Manuals 
						

							Configure the energy save modes of the Océ ColorWave 600
Introduction
The Océ ColorWave 600 offers two energy save modes that you can set if the printer is
idle 
for a defined period. The configuration of the timers prevents unnecessary power
consumption. 
You can adjust the value of the timers.
When 
to do Sleep mode timer (Default value 1 
hour).
The 
Océ ColorWave 600 uses minimal energy, because the power supply of the printer
is turned
 off. The power supply of the embedded Océ ColorWave 600 
controller ('Océ
PowerM controller'
 / 'Océ PowerM Plus controller ') remains on. The printer needs to
warm 
up when it wakes up from the sleep mode.
Energy
 save mode timer (Default value 15 
minutes).
Both the printer and the Océ ColorWave 600 
controller remain turned on. The Océ
ColorWave
 600 
uses less energy than in normal operating mode, but the printer uses
more energy
 than in sleep 
mode. The advantage of the energy save mode over the sleep
mode is
 that the printer usually needs just a few seconds to wake up. Only 
when the
printer has not been used for more than 1 hour does the printer need more time to wake
up.
Note:
The value you set for the sleep mode timer must be higher than the energy save mode
value. 
If the value of the sleep mode is lower than the energy save mode, the printer skips
the energy save mode and goes into sleep mode. The power consumption will be lower
but it will 
also take the printer a bit longer to wake up again. How to configure the time-out value of the energy save modes
1.Click 
'Preferences' - 'System properties'.
2. Click 
'Edit' in the 'Printer properties' bar or click the value of the 'Sleep mode time-out'
setting or the 'Energy saving mode time-out' setting.
3. Enter

 a new value in the Edit window and click 'Ok' to confirm your entries or 'Cancel'
to 
reject your entries.
Note:
If you access the Edit window by clicking the value of the setting you want to change,
the Edit window displays the minimal and maximal value you can 
select. Chapter 4
 - Configure the printing system 123Configure the energy save
 modes of the Océ ColorWave 600
Downloaded From ManualsPrinter.com Manuals 
						

							Note:
When the Océ ColorWave 600 is in the energy save mode, there are two ways to activate
the system.• press a

 key on the printer operator panel.
• send 
a job. Chapter 4
 - Configure the printing system124Configure the energy save
 modes of the Océ ColorWave 600
Downloaded From ManualsPrinter.com Manuals 
						

							Configure the media sizes
Introduction
You must indicate in the Océ Express WebTools the following settings.
• The 
core size of the media rolls
• The 
media sizes How to define the core size of the media
Attention:
Access the Océ Express WebTools. This setting is editable for the Key operator and the
Power user. 1.
Navigate 
to 'Configuration' - 'Printer setup'.
2. Click 
'Edit' in the 'Media' bar or click the value of the 'Two-inch core used' setting if
you 
also use 2 inch cores.
The 
standard roll core size for the Océ ColorWave 600 is 3 inch. If you also use media
rolls 
with 2 inch cores the Océ ColorWave 600 must do some internal adjustments to
also 
support these media.
3. Click 
'Ok' to confirm your entries or 'Cancel' to reject your entries. How to define the media sizes
Attention:
Access the Océ Express WebTools. This setting is editable for the System Administrator
and the Power user.
1.
Navigate 
to the 'Support' - 'Media' tab.
2. Click 
on the value of the 'Supported media sizes' setting. A new window opens.
3. Select the media series from 
the drop-down list. For each of the standard media series
('ANSI small',
 'DIN', 'ANSI mixed' or 'DIN Carto') a set of media sizes is enabled as
indicated 

in the table below. You can enable or disable media sizes to tune the system to
your environment. The media series will then automatically change into a 'Custom' media
series. Chapter 4
 - Configure the printing system 125Configure the media sizes
Downloaded From ManualsPrinter.com Manuals 
						

							#
Media sizes
Media series
42x60 inch, E, D, C, B.
'ANSI small'
42x60
 inch, E+, A0, B1, A1, B2, A2, A3
'DIN'
42x60
 inch, F+, E+, E, D+, D, C+, C, B+, B.
'ANSI
 mixed'
42x60
 inch, 500x700 mm, 700x1000 mm, 800x1189 mm, A0,
A1, A2, A3, B0, E+.
'DIN

 Carto'
...
'Custom'
Note:
You cannot disable media sizes that are currently loaded on the printer.
Note:
When you load a media roll the printer automatically detects the roll width. If the detected
roll width is not a standard width, the printer selects the next smaller roll width that 
is
supported by the printer.
Note:
When you load a media roll with a size that was not yet enabled in the media series, the
system
 automatically adds the new media size to 
the custom media series. 4. Click 
'Ok' to confirm your entries or 'Cancel' to reject your entries.
Chapter 4
 - Configure the printing system126Configure the media sizes
Downloaded From ManualsPrinter.com Manuals 
						

							The 'Configuration' tab in the Océ Express
WebTools
Configure the network settings in the Océ Express WebTools
Introduction
Some of the network settings are configured during the installation of your system. If
you 
want to change the initial configuration or if you want to define more network settings,
you 
can do so in the 'Configuration' - tab.
How 
to configure the network settings in the Océ Express WebTools 1. Click 
'Configuration' - 'Connectivity'.
2. Click 
'Edit' in the group bar to access the 'Edit' window. You can edit all the settings of
the settings group in 
one window.
or
3. To edit only one setting, click a single setting value in the expanded list.
Note:
Log on as System administrator or Power user in the Océ Express WebTools. For example, click on the value of the 'Enable DHCP' setting to display a window where
you 
can change the value.
Note:
This window also contains a short explanation of the setting.
4. Click 
'Ok' to confirm your entries or 'Cancel' to reject your entries.
Chapter 4
 - Configure the printing system 127Configure the network settings in the Océ Express WebTools
Downloaded From ManualsPrinter.com Manuals 
						

							Set the 'Network duplex mode'
Introduction
Use the Océ Express WebTools to set 'Network duplex mode' for your network adapter.
The list of values you can select depends on the type of network card.
Before
 you begin This 
setting is editable for the System administrator or Power user.
How 
to set the 'Network duplex mode' 1. Click 'Configuration' - 'Connectivity'.
2. Click 

'Edit' in the 'Network adapter' bar or click the value of the 'Network duplex mode'
setting.
3. Click 
'Ok' to confirm your entries or 'Cancel' to reject your entries.
Chapter 4
 - Configure the printing system128Set the 'Network duplex mode'
Downloaded From ManualsPrinter.com Manuals 
						

							Set the 'Network speed'
Introduction
Use the Océ Express WebTools to set 'Network speed' for your network adapter.
The 
list of values you can select depends on the type of network card.
Before
 you begin This 
setting is editable for the System administrator or the Power user.
Attention:
Gigabit ethernet (1000 Mbit/s) is supported, but only by automatic detection.
How to set the 'Network speed'
1.Click 
'Configuration' - 'Connectivity'.
2. Click 
'Edit' in the 'Network adapter' bar or click the value of the 'Network speed' setting.
3. Click 
'Ok' to confirm your entries or 'Cancel' to reject your entries.
Chapter 4
 - Configure the printing system 129Set the 'Network speed'
Downloaded From ManualsPrinter.com Manuals 
						

							Relevant settings on the printer operator panel
Change the display language of the printer
Introduction
The Océ Express WebTools allows you to define the 'First language' (the default display
language) and the 'Second language' (the alternative display language) for the printer
operator panel.
The 

'First language' and the 'Second language' you defined in the Océ Express WebTools
are 
also the display languages that are available on the printer operator panel. You can
toggle between
 these two languages using the operator panel.
How 

to change the display language of the printer #
Illustration
Action From 
the 'Home' screen use the lower left softkey to
select 
the 'System' tab.
1 Use the upper right softkey to select the 'Configuration'
tab.2
Chapter 4
 - Configure the printing system130Change the display language of the printer
Downloaded From ManualsPrinter.com Manuals