NEC Neax 2000 Ivs2 Isdn System Manual
Have a look at the manual NEC Neax 2000 Ivs2 Isdn System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
NEAX2000 IVS2 ISDN System ManualPage 70 ND-70919 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING ISDN-PRI Programming For originating calls to the ISDN, do the following programming: DESCRIPTION DATA Assign ISDN access code to each trunk route assigned by CM30 YY=00. NOTE:LCR can be used with ISDN-PRI. Refer to Feature Programming Manual. (1) (2)Y=0-3 Numbering Plan Group 0-3 X-XXXX: Access code 100-163: Trunk Route 00-63 Specify the timing start when making an ISDN call from an attendant.(1) (2)403 0 : Not available 1 : Available Specify the timing start when making an ISDN call from a Single Line Telephone (PB/DP), D term or Attendant Console, if required. (1) (2)Y=0 50 03-14: 3 sec.-14 sec. If no data is set, the timing sta rt is not effective. Recommended setting is 05 (5 seconds). NOTE:A # or timing start is used for outgoing ISDN calls when LCR is not invoked. Example: 1-214-555-1212 is dialed from a D term. The PBX will access a bearer channel and ship the digits only after the timing start timer has expired or # is dialed by the caller. The # sign tells the PBX that dialing is completed. CM08 CM41 CM20 E F
CHAPTER 3 SYSTEM DATA PROGRAMMING ISDN-PRI Programming NEAX2000 IVS2 ISDN System Manual ND-70919 (E), Issue 1.0 Page 71 When providing Tandem Connection (ODT/DTI to ISDN, ISDN to ODT/DTI), do the following programming: DESCRIPTION DATA Specify the combination of trunk routes allowing the tandem connection. (1) (2)Y=0 XX ZZ XX: 00-63: Incoming Trunk Route ZZ : 00-63: Outgoing Trunk Route 0 : Allowed 1: Restricted Specify the timing start when making an ISDN call from a station (PB/DP telephone/D term) or Attendant Console for the Tandem Connection. (1) (2)Y=0 57 03-14: 3 sec.-14 sec. If no data is set, the timing sta rt is not effective. NOTE 1:By using CM41 Y=0>57, an ISDN call is available even if “#” is not dialed. NOTE 2:CM41 Y=0>57 is effective for dialing a called number. When dialing a called party subaddress, this command is not effective. CM41 CM36 F G
NEAX2000 IVS2 ISDN System ManualPage 72 ND-70919 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING ISDN-PRI Programming When providing Tandem Connection (ISDN to CCIS, CCIS to ISDN), do the following programming: DESCRIPTION DATA Specify the combination of trunk routes allowing the tandem connection. (1) (2)Y=0 XX ZZ XX: 00-63: Incoming Trunk Route ZZ : 00-63: Outgoing Trunk Route 0 : Allowed 1: Restricted Allow tandem connection by station or attendant.(1) (2)028 0: Available CM08 END CM36 G
CHAPTER 3 SYSTEM DATA PROGRAMMING ISDN-PRI Programming NEAX2000 IVS2 ISDN System Manual ND-70919 (E), Issue 1.0 Page 73 D Channel Handler Assignment DESCRIPTION DATA When you use the DCH card (PN-SC01), assign an AP number to the DCH card. The AP number must match the SENS switch settings on the DCH card. When you use the PRT card, skip this assignment. (1) (2)Y=0 04-15, 20-31: AP No. 12: DCH card Select DCH for ISDN-PRI. (1) (2)YY=14 04-15, 20-31: AP No. assigned by CM05 0 : PN-24PRTA (Built-in DCH) 1 : PN-SC01 (DCH) Assign the ISDN Protocol Type for DCH/ PRT card. (1) (2)YY=06 04-15, 20-31: AP No. of DCH/PRT card assigned by CM05 ISDN Protocol Type 17 : Australia 18 : New Zealand 19 : ITU-T (Hong Kong) 20 : AT&T (#4, #5 ESS) 21 : NTI (DMS 100, 250) 22 : Australia ETSI 23 : ETSI VN4 (Chile) 24 : ETSI Standard (Brazil, Chile, Columbia) 25 : ITU-T Standard (Thailand) 28 : USA NI-2 63 : Not used Assign the DCH number to the AP number of DCH/PRT card assigned by CM05. (1) (2)YY=08 0-7: DCH No. 04-15, 20-31: AP No. of DCH/PRT card assigned by CM05 Assign the DCH number to the each B channel trunk route assigned by CM30 YY=00. (1) (2)YY=93 Assignment of D Channel Handler 00-63: B channel Trunk Route No. 00-07: DCH No. assigned by CM06 CMAA CM06 CM35 START CM05 A INITIAL DTI INITIAL INITIAL
NEAX2000 IVS2 ISDN System ManualPage 74 ND-70919 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING ISDN-PRI Programming DESCRIPTION DATA Assign the DTI/PRT trunk number assigned by CM07 YY=01 to each DCH number for providing D channel path between DTI/PRT and DCH. (1) (2)YY=00 0-7: DCH No. assigned by CM06 000-255: DTI/PRT Trunk No. assigned by CM07 YY=01 CMA9 A END DCH INITIAL
CHAPTER 3 SYSTEM DATA PROGRAMMING ISDN-BRI Programming NEAX2000 IVS2 ISDN System Manual ND-70919 (E), Issue 1.0 Page 75 ISDN-BRI PROGRAMMING BRT Assignment DESCRIPTION DATA Assign an AP number to the BRT card. The AP number must match the SENS switch setting on the BRT card. (1) (2)Y=0 04-15, 20-31: AP No. 10: BRT card Assign the ISDN Protocol Type for DCH circuit on the BRT card. (1) (2)YY=06 04-15, 20-31: AP No. of BRT assigned by CM05 ISDN Protocol Type 17 : Australia 18 : New Zealand 20 : AT&T (#4, #5 ESS) 21 : NTI (DMS 100, 250) 22 : Australia ETSI 24 : ETSI Standard (Brazil, Columbia, Indonesia) 25 : ITU-T Standard (Thailand) 27 : USA NI-1 28 : USA NI-2 63 : Not used Assign ISDN trunk number to each channel number of BRT. NOTE:Be sure to assign the trunk numbers to all circuits (00-03) of the 2BRTC card, even if only one PCM digital line is accommodated to the card. Set make-busy to the unused trunk numbers by CME5 Y=1, 2nd data=0. (1) (2)YY=02 XX ZZ XX: AP No. assigned by CM05 ZZ : Channel No. (00/01: BRTA) (00-03: 2BRTC) D000-D255: Trunk No. Trunk No. already assigned by CM10 cannot to be used. CMAA CM07 START CM05 A INITIAL DTI INITIAL INITIAL
NEAX2000 IVS2 ISDN System ManualPage 76 ND-70919 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING ISDN-BRI Programming DESCRIPTION DATA Assign trunk route to each ISDN trunk used for Voice channel (B channel). NOTE:BRT route must be separated from analog trunk routes. (1) (2)YY=00 000-255: Trunk No. assigned by CM07 YY=01 00-63: Trunk Route Assign the trunk route data to each ISDN incoming trunk used for Voice channel only. NOTE:If CM35 YYY=143 is set to “1” for Event Based CCIS, this command must be set to “18” (ISDN Indial). (1) (2)YY=02 Day Mode YY=03 Night Mode YY=40 Mode A YY=41 Mode B 000-255: Trunk No. assigned by CM07 YY=01 04: Direct-In Termination 09: Automated Attendant 14: Termination to Attendant Console 16: Remote Access to System (DISA) 18: ISDN Indial Assign ISDN Local Office Code Table number to each ISDN trunk. (1) (2)YY=34 000-255: Trunk No. assigned by CM07 YY=02 00-14: Local Office Table No. 15 : Not assigned Assign trunk route data to the route number assigned by CM30 YY=00. (1) (2) (1) (2)YY=00 Kind of Trunk Route 00-63: B channel Trunk Route No. 00: ISDN Trunk 00-63: D channel Trunk Route No. 15 : Not used (1) (2)YY=02 Call Direction 00-63: B channel Trunk Route No. 3 : Bothway Trunk NOTE 1 (1) (2) (1) (2)YY=04 Answer Signal from distant office 00-63: B channel Trunk Route No. 2: Answer signal arrives (ISDN Trunk) 00-63: D channel Trunk Route No. 7 : Not used CM30 A CM35 B
CHAPTER 3 SYSTEM DATA PROGRAMMING ISDN-BRI Programming NEAX2000 IVS2 ISDN System Manual ND-70919 (E), Issue 1.0 Page 77 DESCRIPTION DATA (1) (2)YY=05 Release signal from distant office 00-63: B channel/D channel Trunk Route No. 1 : Release signal arrives NOTE 2 (1) (2)YY=09 Incoming Connection Signaling 00-63: Trunk Route No. 08: ISDN Indial (1) (2)YY=11 Toll Restriction 00-63: B channel Trunk Route No. 0 : Provided NOTE 1 3 : Not provided (1) (2)YY=12 Number of digit to be received on DID 00-63: B channel Trunk Route No. 0 : 1 digit NOTE 1 1 : 2 digits 2 : 3 digits 3 : 4 digits (1) (2)YY=14 SMDR for outgoing call 00-63: B channel Trunk Route No. 0 : Not provided 1 : Provided NOTE 1 (1) (2)YY=15 Kind of Call Termination Indica- tor Key/Lamp on ATT 00-63: B channel Trunk Route No. 00-07: C.O. Incoming 0-7 NOTE 1 (1) (2)YY=16 Hooking Signal Sending to outside 00-63: B channel Trunk Route No. 0: Not sending NOTE 1 (1) (2)YY=18 Digit conversion on DID call 00-63: B channel Trunk Route No. 0 : Provided NOTE 1 1 : Not provided CM35 B C
NEAX2000 IVS2 ISDN System ManualPage 78 ND-70919 (E), Issue 1.0 CHAPTER 3 SYSTEM DATA PROGRAMMING ISDN-BRI Programming DESCRIPTION DATA NOTE 1:This data should be assigned to the B channel trunk route. For D channel trunk route, no data setting is required. NOTE 2:This data should be assigned to both B channel trunk route and D channel trunk route. (1) (2)YY=19 00-63: B channel Trunk Route No. 0-3 : Programmable PAD (See CM42) 4-7 : Fixed PAD NOTE 1 NOTE:For details of PAD data, refer to Command Manual. (1) (2)YY=28 Outgoing Trunk Queuing 00-63: B channel Trunk Route No. 0: Restricted NOTE 1 (1) (2)YY=39 Trunk release by detection of reversal of tip and ring 00-63: B channel Trunk Route No. 1 : To release NOTE 1 (1) (2)YY=90 Assignment of BRT route for ISDN 00-63: B channel/D channel Trunk Route No. 2: ISDN-Basic Rate Interface NOTE 2 Specify the method of Layer 1 activation. (1) (2)YYY=144 00-63: B channel/D channel Trunk Route No. 0 : Activated by call event 1 : Always activated Assign ISDN Local Office Code. (1) (2)YY=05 00-14: Local Office Table No. assigned by CM30 YY=34 X....X (Max. 12 digits) Assign Service Profile ID (SPID) to each B channel number. [North America Only] (1) (2)YY=30 XX Z XX: 04-15: AP No. assigned by CM05 Z : 0-3: B ch No. XXXX ZZZZ XXXX: ISDN Subscriber No. ZZZZ : SPID CM35 C CM50 CMAC D
CHAPTER 3 SYSTEM DATA PROGRAMMING ISDN-BRI Programming NEAX2000 IVS2 ISDN System Manual ND-70919 (E), Issue 1.0 Page 79 For originating calls to the ISDN network, do the following programming: DESCRIPTION DATA When the data for CM35 YY=18 is set to “0” (Received digits conversion is to be provided), assign the data for interpreting the digits received. (1) (2)YY=01 Day Mode YY=02 Night Mode YY=03 Mode A YY=04 Mode B 000-999: Number Conversion Block No. assigned by CM76 Y=00 X-XXXXXXXX: Station No. to be terminated DXX: Change Terminating System to: D09: Automated Attendant D14: Attendant Console D16: Remote Access to System (DISA) DESCRIPTION DATA Assign ISDN access code to each trunk route assigned by CM30 YY=00. (1) (2)Y=0-3 Numbering Plan Group 0-3 X-XXXX: Access code 100-163: Trunk Route 00-63 Specify the timing start when making an ISDN call from an attendant.(1) (2)403 0 : Not available 1 : Available Specify the timing start when making an ISDN call from a Single Line Telephone (PB/DP), D term or Attendant Console, if required. (1) (2)Y=0 50 03-14: 3 sec.-14 sec. If no data is set, the timing sta rt is not effective. (Dialing terminated by entering #.) Recommended setting is 05 (5 seconds). D E CM76 E CM08 CM41 F CM20