NEC Neax 2000 Ivs2 Isdn System Manual

							 NEAX2000 IVS2 ISDN System ManualPage 100  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-VPN Programming
DESCRIPTION DATA

(1)
(2)YYYY=9000-9025: Digit Addition Pat-
tern No. 00-255
0
X-X...X: Digits to be added (Max. 32 
digits)
To delete the designated digit of an area 
code assigned by YYYY=4000-4007.
(1)
(2)YYYY=5000-5255
153: Designation of digit to be deleted 
from area code assigned by 
YYYY=4000-4007
00 : No digit deletion
01-10: Leading 1-10 digits deletion
 
CCC : No digit deletion
Assign the sending an area code to ISDN 
as a Called Party Subaddress.
(1)
(2)YYYY=5000-5255
155: Designation of sending area code 
as a Called Party Subaddress
0: Available
Specify the maximum number of digits to 
be Dialed by Calling Party.
The maximum number of digits including 
the area codes should be assigned to 
each area code.
(1)
(2)Y=0-7 Area Code Development Pattern 
No. 0-7 assigned by CM8A 
Y=A000
X-X...X: Area code dialed, Max. 8 digits
01-79: 1 digit-79 digits
24 : 24 digits
Assign the Area Code Development 
Pattern number for Toll Restriction and 
maximum digit analysis to each trunk 
route.
(1)
(2)YY=76
00-63: Trunk Route No. 
00-07: Area Code Development 
Pattern No. 0-7
CM85
CM35
CM8A
A
END 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 101
ISDN TERMINAL DATA PROGRAMMING
 ILC Assignment 
DESCRIPTION DATA
Assign an ISDN line station number to the 
required LEN.(1)
(2)000-763: LEN
EFX-EFXXXXXXXX: ISDN Line Station 
No.
Assign a Tenant number to each ISDN line 
station number.
(1)
(2)YY=04
X-XXXXXXXX: ISDN Line Station No.
00-63: Tenant No.
If no data is set, the default data is 01.
Assign a Trunk Restriction Class to each 
ISDN line station number.
(1)
(2)YY=01
X-XXXXXXXX: ISDN Line Station No.
X Z: Trunk Restriction Class
X: 1 -8: Trunk Restriction Class in Day 
Mode 
Z: 1 -8: Trunk Restriction Class in 
Night Mode
1: Unrestricted (RCA) 
2: Non-Restricted 1 (RCB) 
3: Non-Restricted 2 (RCC) 
4: Semi-Restricted 1 (RCD) 
5: Semi-Restricted 2 (RCE)
6: Restricted 1 (RCF)
7: Restricted 2 (RCG)
8: Fully-Restricted (RCH)
Assign an ISDN Indial number to the 
required ISDN line station number.
(1)
(2)YY=12
X-XXXXXXXX: ISDN Line Station No.
X-XXXX: ISDN Indial No.
Assign a Local Office Code Table number 
to the required ISDN line station number.
(1)
(2)YY=13
X-XXXXXXXX: ISDN Line Station No.
00-14: ISDN Local Office Code Table 
No. 00-14
CM12 START
CM10
A 
						

							 NEAX2000 IVS2 ISDN System ManualPage 102  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
DESCRIPTION DATA
Specify the facility control of CPN (Calling 
Par ty Number).
(1)
(2)YY=25
X-XXXXXXXX: ISDN Line Station No.
0 : Provided
1 : Not provided
Assign the digit number of ISDN line 
station number.
(1)
(2)Y=0-3
X-XXXX: Access Code
801-808: 1 digit-8 digits
Specify whether the subaddress is sent to 
ISDN when making a call from ISDN 
Terminal, if required.(1)
(2)430
0 : Sent (As per CM08>431)
1 : Not sent
Specify the Calling Party Subaddress 
which is sent to ISDN when making a call 
from ISDN Terminal, if required.(1)
(2)431
0 : ISDN Line Station No. assigned by 
CM10 
1 : ISDN Terminal No.
Specify the forced release when a called 
ISDN Terminal does not answer during 3 
minutes, if required.(1)
(2)432
0 : Not available
1 : Available
Assign CPN (Calling Party Number) which 
is sent to ISDN when making a call from 
ISDN Terminal, if required.(1)
(2)434
0 : CPN entered in ISDN Terminal
1 : CPN assigned by CM12 Y=12/13
Specify the make busy of B channel (B1, 
B2) for ISDN Terminal, if required.
(1)
(2)Y=2
XXXXXXXX  Z
XXXXXXXX: ISDN Line Station No.
Z: 0: B1 channel
1: B2 channel
0: Make busy
1 : In service
CM08
CME5
CM13
A
CM20
END
, 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 103  
ICH Assignment 
DESCRIPTION DATA
Assign an AP number to each ICH card 
(PN-SC03). The AP number must match 
the SENS switch setting on the ICH card.
(1)
(2)Y=0
04-15: AP No.
13: ICH card
Assign the ICH number to the AP number 
of ICH assigned by CM05.
(1)
(2)YY=09
00-15: ICH No.
04-15: AP No. assigned by CM05
Assign the ISDN line station number to the 
ISDN line number of ICH card.
(1)
(2)YY=00
XX Z
XX: 00-15: ICH No.
Z : 0-7: ISDN Line No. of ICH card
X-XXXXXXXX: ISDN Line Station No.
Specify the method of TEI (Terminal End-
point Identifier) assignment.
NOTE:CMAC YY=02 must be assigned 
to match the specification of ISDN 
Terminal.
(1)
(2)YY=02
XX Z
XX: 00-15: ICH No.
Z : 0-7: ISDN Line No. of ICH card
0 : Manual TEI Assignment 
1 : Automatic TEI Assignment
Specify the method of Layer 1 activation.
NOTE:CMAC Y=04 must be assigned to 
match the specification of ISDN 
Terminal.
(1)
(2)YY=04
XX Z
XX: 00-15: ICH No.
Z : 0-7: ISDN Line No. of ICH card
0 : Always activated 
1 : Activated by call event
Assign the ISDN Protocol Type to the AP 
number assigned by CM05.
(1)
(2)YY=06
04-15: AP No. of ICH assigned by 
CM05
24 : ETSI Terminal
63 : Not ETSI Terminal
CM06 START
CM05
CMAC
CMAA
END
INITIAL
INITIAL
INITIAL
INITIAL
INITIAL
INITIAL 
						

							 NEAX2000 IVS2 ISDN System ManualPage 104  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
Point-to-Point Connection
DESCRIPTION DATA
Assign the point to point connection as the 
Layer 2 data link.
(1)
(2)YY=01
XX Z
XX: 00-15: ICH No.
Z : 0-7: ISDN Line No. of ICH card
0: Point to Point Connection
NOTE:When Point-to-Point Connection is selected, the PBX will address the BRI Terminal 
with channel select (B1/B2) message. Some BRI Terminals cannot answer the call 
with this type of signaling. Some of the BRI Terminals require a Calling Party 
Number sent from the PBX. In this case, use Point-to-Multipoint for CMAC YY=01 
and CM1B to assign extension number for the BRI Terminal.
Assign the TEI Manual Assignment.
(1)
(2)YY=02
XX Z
XX: 00-15: ICH No.
Z : 0-7: ISDN Line No. of ICH card
0: TEI Manual Assignment
Assign the Extended Passive Bus.
(1)
(2)YY=03
XX Z
XX: 00-15: ICH No.
Z : 0-7: ISDN Line No. of ICH card
0: Extended Passive Bus
Assign the always activated as the method 
of Layer 1 activation.
(1)
(2)YY=04
XX Z
XX: 00-15: ICH No.
Z : 0-7: ISDN Line No. of ICH card
0: Always activated
MDF
ISDN Terminal/TA
Max. 1965 ft. (600 m)
ILCPBX
CMAC START
END
INITIAL
INITIAL
INITIAL
INITIAL 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 105
Point-to-Multipoint Connection
DESCRIPTION DATA
Assign the point to multipoint connection 
as the Layer 2 data link.
(1)
(2)YY=01
XX Z
XX: 00-15: ICH No.
Z : 0-7: ISDN Line No. of ICH card
1 : Point-to-Multipoint Connection
Specify the passive bus.
(1)
(2)YY=03
XX Z 
XX: 00-15: ICH No.
Z : 0-7: ISDN Line No. of ICH card
0 : Extended Passive Bus 
1 : Short Passive Bus
Assign an ISDN Terminal Multipoint 
station number to the ISDN Line station 
number.
The numbers assigned in this command 
are station numbers that are to be 
programmed in the BRI terminal. CM12 
YY=12 will use the station assignment 
from CM10.(1)
(2)XXXXXXXX  Z
XXXXXXXX: ISDN Line Station No. 
assigned by CM10
Z: 0-7: ISDN Multipoint No.
X-XXXXXXXX: ISDN Terminal 
Multipoint Station No.
400407
410417
ILC
 Short Passive Bus
 Extended Passive Bus
MDF
ISDN Terminal
ISDN Terminal301 300
MDF
ILC
PBX
Max. 1310 ft. (400 m) Max. 164 ft. (50 m)Max. 491 ft. (150 m)
START
CMAC
END
CM1B
INITIAL
INITIAL
, 
						

							 NEAX2000 IVS2 ISDN System ManualPage 106  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
BRI Programming Example:
The following is an example of common BRI Station Programming.
CM10024>EF2125
025>EF2126
CM AC00>000-2125
001-2126
CM
CM
CM
CM
CMAC01>000-1
001-1
AC02>000-1
001-1
AC03>000-1
001-1
AC04>000-1
001-1
AC06>000-1
001-1CM1B>2125, 0>2225*
2125, 1>2226
2
>None
7
2126, 0>2235*
2126, 1>2236*
2
>None
7
* Ext. 2225 and others assigned in CM1B are the
Extension numbers that should be entered into the BRI
Terminal(s). Most BRI Terminals require a 10-digit
number.
If the BRI Terminals require a SPID [North America
Only], it is common to add a 3-digit number to the main
number.
For example:
Main number (1) : 214-555-2225
Main number (2) : 214-555-2226
SPID (1) : 214-555-2225123
SPID (2) : 214-555-2226123
SPIDs are required for NI-1 protocol and AT&T Point-to-
Multipoint. Devices that are set as AT&T Point-to-Point do
not use SPIDs.
~~ 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 107
Individual Terminal Call 
(1) ISDN Indial
When receiving an ISDN Terminal station number as the ISDN Indial number, or when
converting an ISDN Indial number to an ISDN Terminal station number, by CM76, the
system connects the call with the specified ISDN Terminal or Terminal Adapter (TA) on the
same bus (2B + D).
Do the following programming:
DID Addressing  (See Page 83.)
Point-to-Multipoint Connection   (See Page 105.)
ISDN
ISDN Terminal
Station No. 407ISDN Terminal
Station No. 400ISDN Line
Station No. 300
ILCConverting “7715” to ”400”
TRK
PBX
214-555-7715
(ISDN Indial No.) 
						

							 NEAX2000 IVS2 ISDN System ManualPage 108  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
(2) Called Par ty Subaddress
When the system has received a Called Party Subaddress (ISDN Terminal station number)
from an ISDN Subscriber, the system connects the call with the specified ISDN Terminal or
TA on the same bus (2B + D).
Do the following programming:
Subaddress-Present   (See Page 89.)
Point-to-Multipoint Connection   (See Page 105.)
ISDN
ISDN Terminal
Station No. 407ISDN Terminal
Station No. 400ISDN Line
Station No. 300
ILC TRKPBX
214-555-1111
(Office No.)
-400
(Called Par tySubaddress=
ISDN Terminal Station No.) 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 109
(3) Direct In Termination (DIT)
When the ISDN Terminal station number is assigned as the destination of DIT, the system
connects the call with the specified ISDN Terminal or TA on the same bus (2B + D).
In addition to the programming of Point-to-Multipoint Connection on Page 105, do the
following programming:
DESCRIPTION DATA
Assign the data for DIT to the trunk 
numbers assigned by CM07.



(1)
(2)YY=02 Day Mode
YY=03 Night Mode
YY=40 Mode A
YY=41 Mode B
000-255: Trunk No. assigned by CM07 
YY=01
04: Direct-In Termination
Assign the ISDN Terminal station number 
to be terminated by Direct In Termination.



(1)
(2)YY=04 Day Mode
YY=05 Night Mode
YY=42 Mode A
YY=43 Mode B
000-255: Trunk No. assigned by CM07 
YY=01
X-XXXXXXXX: ISDN Terminal Station 
No.
ISDN
ISDN Terminal
Station No. 407ISDN Terminal
Station No. 400ISDN Line
Station No. 300
ILC TRKPBX
214-555-7881
(Office No.)
START
CM30
END