NEC Neax 2000 Ivs2 Isdn System Manual

							 NEAX2000 IVS2 ISDN System ManualPage 60  ND-70919 (E), Issue 1.0
CHAPTER 2  INSTALLATION
Installation Procedure for ISDN Terminal
Figure 2-15  Example of MDF Cross Connection for ILC
1
2
3
4
5
6
7 8
Pin No.
LT 0 0PIM0
ILC J PLT C 0
RA0
TB1 RB1
TB0
RB0
TA 0
RA1
TA 11
29 28
27
26
2
3
41
29 28
27
26
2
3
4
MDF
RA
RB
TA
TB RECEIVE
SEND3
6
4
5TO ISDN
TERMINAL
1RA26RBLT C  ( J )
2TA27TB
328
429
26 RB 1 RA
27 TB 2 TA
28 3
29 4
Pin No. PBX Direction of Signal Terminal
1
2
3RA←TA
4TA→RA
5TB→RB
6RB←TB
7
8Not Used
Not Used
Modular Connector
LT C  ( P ) 
						

							CHAPTER 2  INSTALLATION
Installation Procedure for Event Based CCIS
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 61
INSTALLATION PROCEDURE FOR EVENT BASED CCIS
Install the equipment for Event Based CCIS according to the procedure shown in Figure 2-16.
NOTE:For Call Recording of ISDN call, install the equipment for SMDR/CIS. For details, refer
to the Installation Procedure Manual.
Figure 2-16  Installation Procedure for Event Based CCIS
END START
Mounting 
PRT Card or BRT Card
DTI/PRT/BRT Card Cable 
Connection via MDF
Selection of PLO in
MP Card DTI and DCH Card/
Mounting CCH CardDTI/DCH/PRT See Page 42.
BRT See Page 50.
See CHAPTER 4.
See Page 62.
or via CONN CardDTI/PRT SeePage 44.
CONN SeePage 47.
BRT See Page 51. 
						

							 NEAX2000 IVS2 ISDN System ManualPage 62  ND-70919 (E), Issue 1.0
CHAPTER 2  INSTALLATION
Installation Procedure for Event Based CCIS
Mounting CCH Card
(1) Before mounting the CCH (PN-SC00) card, set the MB switch to UP 
position, and set the other switches to appropriate position.
See CHAPTER 4.
(2) Mount the CCH card in the following AP slots:
PIM0-7: AP00-AP11
The AP11 slot on PIM0 is available only when the FP card is not mounted in the FP11 slot 
on PIM0.
(3) After mounting the card, set the MB switch to DOWN position to put the card in service.
ATTENTIONContents
Static Sensitive
Handling
Precautions Required 
						

							NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 63
CHAPTER 3
SYSTEM DATA 
PROGRAMMING
This chapter explains the programming procedure to provide the ISDN
feature to the PBX. 
						

							 NEAX2000 IVS2 ISDN System ManualPage 64  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
How to Read This Chapter
HOW TO READ THIS CHAPTER
In the programming procedure, the meaning of (1), (2), and markings are as follows:
(1) : 1st Data
(2) : 2nd Data
: Initial Data
With the system data clear command (CM00, CM01), the data with this marking is
automatically assigned for each command.
: System Initialization
A reset of the MP card is required after data setting.
Press SW1 switch on the MP card.
: DTI Initialization
A reset of the DTI/PRT card is required after data setting.
Set the Make Busy switch to UP and then Down.
: DCH Initialization
A reset of the DCH card is required after data setting.
Set the Make Busy switch to UP and then Down.
INITIAL
DTI INITIAL
DCH INITIAL 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 65
ISDN-PRI PROGRAMMING
Digital Trunk Data Assignment
DESCRIPTION DATA
Assign an AP number to the DTI/PRT 
card. 
The AP number must match the SENSE 
switch setting on the DTI/PRT card.
(1)
(2)Y=0
04-15, 20-31: AP No.
09: DTI card
12: PRT card
Specify the AP highway channel for 24DTI/
PRT card.
(1)
(2)Y=1
04-15, 20-31: AP No.
0 : Expanded Highway channel 
(128 time slots)
1 : Basic Highway channel 
(128 time slots)
Assign trunk numbers to each channel 
number on the DTI/PRT card.
The system allocates time slots to 
consecutive channels from lowest to 
highest channel number assigned. To 
minimize the number of time slots 
allocated, assign trunk numbers to the 
consecutive channels on each card.
Never skip channels in CM07.
(1)
(2)YY=01
XX ZZ 
XX: 04-15, 20-31: AP No. assigned by 
CM05
ZZ: 00-23: Channel No. of 24DTI/PRT
01-15, 17-31: Channel No. of 
30DTI
D000-D255: Trunk No.
Any trunk No. already assigned by 
CM10 cannot be used.
Allow second Dial Tone when dialing 
access code assigned by CM20 for ISDN 
B channel route.
(1)
(2)Y=2
04
0 : For ISDN trunk route, 2
nd Dial Tone 
is provided.
1: No 2
nd Dial Tone
CM07 START
CM05
A
CM48
INITIAL
INITIAL
INITIAL 
						

							 NEAX2000 IVS2 ISDN System ManualPage 66  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
DESCRIPTION DATA
Assign the necessary functions to the DTI/
PRT card. CMAA YY=00/01/02 assign-
ment is required only for 24DTI/PRT.
After entering the data, set the MB switch 
on the DTI/PRT card to UP, and then to 
DOWN, for DTI/PRT initialization.
NOTE:The following table shows the 
relationship between CMAA 
YY=01 and YY=02.
(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)YY=00 Data Mode
04-15, 20-31: AP No. assigned by 
CM05
0: Based on AT&T Spec.
YY=01 Frame Configuration
04-15, 20-31: AP No. assigned by 
CM05
0 : 12-Multi Frame
1 : 24-Multi Frame
YY=02 Zero Code Suppression
04-15, 20-31: AP No. assigned by 
CM05
0 : Available
1 : Not available
YY=03
04-15, 20-31: AP No. assigned by 
CM05
7 : Associated Channel 
Interoffice Signaling
Assign a trunk route number to each ISDN 
trunk used for voice channel and also to 
signaling channel. The DTI route must be 
separated from any analog trunk route.
(1)
(2)YY=00
000-255: Trunk No. assigned by CM07 
YY=01
00-63: Trunk Route No.
Assign the trunk route data to each ISDN 
incoming trunk used for Voice channel 
only. 



(1)
(2)YY=02 Day Mode
YY=03 Night Mode
YY=40 Mode A
YY=41 Mode B
000-255: Trunk No. assigned by CM07 
YY=01
02: Trunk Line Appearance
03: Trunk Line Appearance + TAS
04: Direct-In Termination
09: Automated Attendant
14: Termination to Attendant console
16: Remote Access to System (DISA)
18: ISDN Indial
CMAA
A
CM30
B
DTI INITIAL
 [ ]: Indicates 2nd data
CMAA YY=01 
(FRAME CON-
FIGURATION)CMAA YY=02 
(ZERO CODE 
SUPPRES-
SION)SIGNALING
24-Multi Frame 
[1]
B8ZS
12-Multi Frame 
[0]Not available [1] Transparent
Available [0] B7 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 67
DESCRIPTION DATA
Assign Circuit Identification Code (CIC) 
number to each ISDN trunk used for voice 
channel only.
NOTE:CIC No. must not be assigned to 
the trunk No. of D channel: TS16 
(30DTI) or TS23 (24DTI/PRT).
(1)
(2)YY=07
000-255: Trunk No. assigned by CM07 
YY=01
000-029: CIC No.
EXAMPLE OF 30DTI
B channel trunk No.: D100-D114, D116-
D130
D channel trunk No.: D115
(1) 100-114, 116-130
(2) 000-014, 015-029
EXAMPLE OF 24DTI/PRT
B channel trunk No.: D100-D122
D channel trunk No.: D123
(1) 100-122
(2) 000-022
Assign trunk route data to the route 
number assigned by CM30 YY=00.
(1)
(2)
(1)
(2)YY=00 Kind of Trunk Route
00-63: B channel Trunk Route No.
00: ISDN Trunk
00-63: D channel Trunk Route No.
15 : Not used

(1)
(2)YY=02 Call Direction
00-63: B channel Trunk Route No.
3 : Bothway Trunk  
NOTE 1

(1)
(2)
(1)
(2)YY=04 Answer Signal from distant 
office
00-63: B channel Trunk Route No.
2: Answer signal arrives (ISDN Trunk) 
00-63: D channel Trunk Route No.
7 : Not used 
CM30
B
CM35
C 
						

							 NEAX2000 IVS2 ISDN System ManualPage 68  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
DESCRIPTION DATA

(1)
(2)YY=05 
Release Signal from distant office
00-63: B channel/D channel Trunk 
Route No.
1 : Release signal arrives 
NOTE 2

(1)
(2)
(1)
(2)YY=09 Incoming Connection Signaling
00-63: B channel Trunk Route No.
08: ISDN
00-63: D channel Trunk Route No.
15 : Not used

(1)
(2)YY=11 Toll Restriction
00-63: B channel Trunk Route No.
0 : Provided  
NOTE 1
3 : Not provided

(1)
(2)YY=12 
Number of digits to be received on DID
00-63: B channel Trunk Route No.
0 : 1 digit
1 : 2 digits
2 : 3 digits
3 : 4 digits
NOTE:If CM35 YYY=143 is set to “1” 
for Event Based CCIS, the 
number of digits received on 
DID must be assigned.

(1)
(2)YY=14 SMDR for outgoing call
00-63: B channel Trunk Route No. 
0 : Not provided
1 : Provided  
NOTE 1

(1)
(2)YY=15 Kind of Call Termination Indica-
tor Key/Lamp on ATT
00-63: B channel Trunk Route No.
00-07: C.O. Incoming 0-7  
NOTE 1
CM35
C
D 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-PRI Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 69
DESCRIPTION DATA
NOTE 1:This data should be assigned to 
the B channel trunk route.  For 
D channel trunk route, no data 
setting is required.
NOTE 2:This data should be assigned to 
both B channel trunk route and 
D channel trunk route.
(1)
(2)YY=16 
Hooking Signal Sending to outside
00-63: B channel Trunk Route No.
0: Not sending  
NOTE 1

(1)
(2)YY=18 Digit conversion on DID call
00-63: B channel Trunk Route No.
0 : Provided
1 : Not provided

(1)
(2)YY=19 
00-63: B channel Trunk Route No. 
0-3 : Programmable PAD 
(See CM42)
4-7 : Fixed PAD   
NOTE 1
NOTE:For details of PAD data, refer to 
Command Manual.

(1)
(2)YY=28 Outgoing Trunk Queuing
00-63: B channel Trunk Route No.
0: Restricted  
NOTE 1

(1)
(2)YY=39 Trunk release by detection of 
reversal of tip and ring
00-63: B channel Trunk Route No.
1 : To release  
NOTE 1

(1)
(2)YY=89 CRC error check
00-63: B channel Trunk Route No.
0: Provided  
NOTE 1

(1)
(2)YY=90 Assignment of DTI route for 
ISDN
00-63: B channel/D channel Trunk 
Route No.
3: ISDN-Primary Rate Interface
NOTE 2
CM35
D
E