NEC Neax 2000 Ivs2 Isdn System Manual

							 NEAX2000 IVS2 ISDN System ManualPage 80  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-BRI Programming
 When providing Tandem Connection (COT/ODT/LDT/DTI to ISDN, ISDN to COT/ODT/LDT/
DTI), do the following programming:
DESCRIPTION DATA
Specify whether the busy tone is sent to a 
calling party of ISDN when a called party 
is busy in the tandem connection (ISDN to 
COT).(1)
(2)407
0 : Available (BT)
1 : Not available (RBT)
Specify the combination of trunk routes 
allowing the tandem connection.
(1)
(2)Y=0
XX ZZ
XX: 00-63: Incoming Trunk Route
ZZ : 00-63: Outgoing Trunk Route
0 : Allowed
1: Restricted
Specify the timing start when making an 
ISDN call from a station (PB/DP telephone 
D
term) or Attendant Console for the 
Tandem Connection.
(1)
(2)Y=0
57
03-14: 3 sec.-14 sec.
If no data is set, the timing sta rt is not 
effective.
NOTE 1:By using CM41 Y=0>57, an ISDN call is available even if “#” is not dialed.
NOTE 2:CM41 Y=0>57 is effective for dialing a called number. When dialing a called party 
subaddress, this command is not effective.
CM08
F
CM36
CM41
G 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN-BRI Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 81
 When providing Tandem Connection (ISDN to CCIS, CCIS to ISDN), do the following
programming:
 Specify whether the Calling Party Number (CPN) sent from ISDN is sent to the CCIS
network.
DESCRIPTION DATA
Specify the combination of trunk routes 
allowing the tandem connection.
(1)
(2)Y=0
XX ZZ
XX: 00-63: Incoming Trunk Route
ZZ : 00-63: Outgoing Trunk Route
0 : Allowed
1: Restricted
Allow tandem connection by station or 
attendant.(1)
(2)028
0: Available
DESCRIPTION DATA
Maximum number of digits sent to CCIS 
network.(1)
(2)379
0: 24 digits
Activate IAI2 message for sending ISDN 
CPN to CCIS network.
(1)
(2)YY=26
0-7: CCIS Channel No.
0: Active
Allow sending of CPN to CCIS network.
(1)
(2)YY=28
0-7: CCIS Channel No.
0: Allowed
CM36
G
CM08
END
CM08
CMA7
END
START 
						

							 NEAX2000 IVS2 ISDN System ManualPage 82  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
ISDN FEATURE PROGRAMMING
 Calling Party Recognition Service (Direct-In Termination (DIT))
Refer to “Direct Inward Termination (DIT)” in the Feature Programming Manual.
 DID Addressing    (See Page 83.)
MEGACOM
® Access [North America Only]   (See Page 85.)
MEGACOM
® 800 Service [North America Only] 
Refer to “DID Addressing” for programming instructions.   (See Page 83.)
 SID to Network-Present 
[Australia/Other Countries]   (See Page 86.)
 CPN to Network-Present 
[North America]   (See Page 86.)
 SID to Terminating User-Display 
[Australia/Other Countries]
No programming is required.
 CPN to Terminating User-Display 
[North America]
No programming is required.
 Subaddress-Present   (See Page 89.)
 Trunk Provisioning Service Selection   (See Page 90.)
 ISDN PRI Call By Call Service Selection 
[North America Only]   (See Page 91.)
 Advice of Charge (AOC) 
[Australia/France Only]  (See Page 97.)
 Centrex SHF over ISDN 
[N.Z. Only]  (See Page 98.) 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 83
DID Addressing
DESCRIPTION DATA
Assign the data for DID to the trunk 
numbers assigned by CM07. 



(1)
(2)YY=02 Day Mode
YY=03 Night Mode
YY=40 Mode A
YY=41 Mode B
000-255: Trunk No. assigned by CM07 
YY=01
18: ISDN Indial
Assign the data for DID to the trunk routes 
assigned by CM30.
(1)
(2)YY=00 Kind of Trunk
00-63: Trunk Route No.
00: DID

(1)
(2)YY=02 OG/IC
00-63: Trunk Route No.
3 : Bothway Trunk

(1)
(2)YY=05 Release Signal Condition
00-63: Trunk Route No.
1 : Release signal arrives

(1)
(2)YY=09 Incoming Connection Signaling
00-63: Trunk Route No.
08: ISDN

(1)
(2)YY=12 Number of digits to be received 
00-63: Trunk Route No.
0 : 1 digit 
1 : 2 digits
2 : 3 digits
3 : 4 digits
PBX
555-9676
555-9677
TRK
555-9677
ISDN
Calling
Pa r ty
CM35 START
CM30
A 
						

							 NEAX2000 IVS2 ISDN System ManualPage 84  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
DESCRIPTION DATA

(1)
(2)YY=18 Received Digit Conversion
00-63: Trunk Route No.
0 : Provided
1 : Not provided 
Assign the destination of DID Call 
transferred when the station is busy/
unassigned/no answer. 


(1)
(2)YY=00 No Answer
YY=03 Busy
YY=06 Unassigned
00-63: Tenant No.
Destination:
X-XXXXXXXX: Station No.
E000 : Attendant Console
EBXXX: Announcement Service:
Digital Announcement Trunk 
No. set by CM10
Assign the Number Conversion Block No. 
(1)
(2)YY=00
X-XXXX: DID No.
000-999: Number Conversion Block 
No.
When the data for CM35 YY=18 is set to 
“0” (Received digit conversion is to be 
provided), assign the data for interpreting 
the digits received.



(1)
(2)YY=01 Day Mode
YY=02 Night Mode
YY=03 Mode A
YY=04 Mode B
000-999: Number Conversion Block 
No. assigned by CM76 
YY=00.
X-XXXXXXXX: Station/Data station/
ISDN line station No. to 
be terminated
DXX: Change Terminating System to:
D04: Direct-in Termination
D14: Attendant Console
CM35
A
CM51
END
CM76 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 85
MEGACOM® Access
[North America Only]
In addition to the programming of Direct Outward Dialing, assign WATS line to the required trunk
route, as shown below:
DESCRIPTION DATA
Assign the Trunk Restriction Class to each 
station.
(1)
(2)YY=01 Trunk Restriction Class
X-XXXXXXXX: Station No.
XZ
X: 1 -8: Trunk Restriction Class in Day 
mode
Z: 1 -8: Trunk Restriction Class in 
Night mode
1: Unrestricted (RCA)
2: Non-Restricted 1 (RCB)
3: Non-Restricted 2 (RCC)
4: Semi-Restricted 1 (RCD)
5: Semi-Restricted 2 (RCE)
6: Restricted 1 (RCF)
7: Restricted 2 (RCG)
8: Fully-Restricted (RCH)
Set the outgoing/incoming Trunk Route 
Restriction data by Trunk Restriction 
Classes (RCA-RCH).

(1)
(2)YY=51-58 Outgoing Trunk Restriction
YY=61-68 Incoming Trunk Restriction
00-63: Trunk Route No.
0 : Restricted
1 : Allowed
NOTE:If Call-By-Call Service Selection is required, seePage 91 for additional 
programming.
DESCRIPTION DATA
Assign a WATS line to the required trunk 
route.
(1)
(2)YY=00
00-63: Trunk Route No.
02: WATS lineSTART
CM12
END
START
CM35
END 
						

							 NEAX2000 IVS2 ISDN System ManualPage 86  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
SID to Network-Present/
CPN to Network-Present
For providing the Calling Party Number (CPN)
to the network, do the following programming:
 When Dial-In service is provided:
 When ISDN (BRI) Terminals are used:
DESCRIPTION DATA
Assign an ISDN Subscriber number and 
ISDN Local Office Code Table number to 
required stations.  
NOTE 1

(1)
(2)YY=12
X-XXXXXXXX: Station No.
X-XXXX: ISDN Subscriber No.

(1)
(2)YY=13
X-XXXXXXXX: Station No.
00-14: ISDN Local Office Code Table 
No. 00-14
Specify the facility control of CPN (Calling 
Par ty Number).
(1)
(2)YY=25
X-XXXXXXXX: Station No.
0 : To provide
1 : Not provided
Assign ISDN Local Office Code to the 
Table number assigned by CM12 YY=13.
(1)
(2)YY=05
00-14: ISDN Local Office Code Table 
No. 00-14
X...X: Local Office Code
(Max. 12 digits)
DESCRIPTION DATA
Allow the ISDN Terminal to send the CPN 
to network without using PBX 
programming.(1)
(2)434
0 : CPN set in ISDN Terminal
1 : CPN assigned by CM12 YY=12, 
13
DIAL “516-555-4210#”
(214-555-5000)
(214-555-5001)
(214-555-5002)
CALLING PARTY No.DTI PBX
ISDN
516-555-4210
+214-555-5000
CALLING PARTY No.
4210
START
CM12
END
CM13
CM50
NOTE 2
START
CM08
END 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 87
NOTE 1:The ISDN number consists of the following numbers:
ISDN number: XXXXXXXXXXXX YYYY
ISDN subscriber No. assigned by CM12 
YY=12 (1-4 digits)
ISDN Local Office Code assigned by 
CM50 YY=05 (1-12 digits)
This number must be in the indial range assigned by Telecom for the ISDN line.
For example:
National Destination Code for Dallas: 214
Local Code for a station: 518-5000
In this case, the ISDN Number is
National Destination Code + Local Code=214518-5000
That is
ISDN Subscribers No. assigned by CM12 YY=12 is 5000.
ISDN Local Office Code assigned by CM50 YY=05 is 214518.
NOTE 2:The following facility control services for CPN are available in accordance with the
subscription category of distant ISDN exchange. In case of no subscription, SID (CPN)
to Network-Present is not available.
Station 5000 places an outgoing call to an ISDN subscriber. Because CM13>25 is set
to 0, the ISDN network is instructed to not send 214-518-5000 (see NOTE 1) to the
distant ISDN subscriber.
Station 5001 places an outgoing call to an ISDN subscriber, and 214-518-5001 is
sent to the called party.
Example:
1st Data  2nd Data Meaning
CM13 YY=25 5000 0 Restrict transfer
5001 1 Permit transfer 
						

							 NEAX2000 IVS2 ISDN System ManualPage 88  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
 When Dial-In service is not provided:
DESCRIPTION DATA
Specify the sending out of CPN (Calling 
Par ty Number).
(1)
(2)YY=25
X-XXXXXXXX: Station No.
0 : Sent
1 : Not sent
Assign an ISDN subscriber number to 
each ISDN trunk.
NOTE 1 on previous page
(1)
(2)YY=19
000-255: Trunk No. assigned by CM07 
YY=01
XXXX: ISDN Subscriber No.
Assign ISDN Local Office Code Table 
number to each ISDN trunk.
(1)
(2)YY=34
000-255: Trunk No. assigned by CM07 
YY=01
00-14: Local Office Code Table No. 00-
14
Assign ISDN Local Office Code to the 
Table number assigned by CM30 YY=34.
(1)
(2)YY=05
00-14: ISDN Local Office Code Table 
No. 00-14
X...X: Local Office Code 
(Max. 12 digits)
DIAL “516-555-4210#”
(214-555-5000)CALLING PARTY No.
DTI PBX
ISDN
516-555-4210
#214-555-5000
CALLING PARTY No.
555-4210
START
CM13
END
CM50
CM30
NOTE 2 on 
previous page 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Feature Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 89
Subaddress-Present
(1) Calling Party Subaddress
When a station has dialed an ISDN 
subscriber number, the station number is 
automatically sent as a Calling Party 
Subaddress.
(2) Called Par ty Subaddress
When the system has received a 
Called Par ty Subaddress (Calling 
Station Number) from an ISDN 
subscriber, the system connects the 
call with the specified terminal.
DESCRIPTION DATA
Provide the system with Calling Party 
Subaddress to ISDN.(1)
(2)400
0: Sent
DESCRIPTION DATA
Specify the terminating system for Called 
Party Subaddress.
NOTE:If CM35 YYY=143 is set to “0” for 
Event Based CCIS, assign the 
second data to “0”.(1)
(2)401
0 : Station Call
1 : Terminating System assigned by 
CM30 YY=02/03/40/41
PBX
TRK
ISDN
555-5000
4211
4211
Calling Party
Subaddress
Dial
214-555
-5000
START
CM08
END
TRK
TRK
ISDN
Subaddress
Dial 214-555-5000 
+ 4211
4210214-555-5000 + 4211
4211
4212
START
CM08
END