NEC Neax 2000 Ivs2 Isdn System Manual

							 NEAX2000 IVS2 ISDN System ManualPage 110  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
(4) Station to Station Calling
When an ISDN Terminal user dials an ISDN Terminal station number within the system, the
system connects the call with the specified ISDN Terminal.
Do the programming of Point-to-Multipoint Connection. See Page 105.
ISDN
ISDN Terminal
Station No. 407ISDN Terminal 
Station No. 400ISDN Line
Station No. 300
ILC TRKPBX
ISDN Terminal
Station No. 417ISDN Terminal
Station No. 410ISDN Line
Station No. 301
ILC
ISDN Terminal Station No. 410 dials 400 to reach
ISDN Terminal 400 specifically. 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 111
Group Call
(1) ISDN Indial
When receiving an ISDN line station number as ISDN Indial number, or when converting an
ISDN Indial number to an ISDN line station number by CM76, the system connects the call
with all ISDN Terminals or Terminal Adapters (TA) on the same bus (2B + D).
Do the following programming:
DID Addressing  (See Page 83.)
Point-to-Multipoint Connection   (See Page 105.)
ISDN
ISDN Terminal
Station No. 407ISDN Terminal
Station No. 400ISDN Line
Station No. 300
ILCConverting “7715” to ”300”
TRK
PBX
214-555-7715
(ISDN Indial No.) 
						

							 NEAX2000 IVS2 ISDN System ManualPage 112  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
(2) Called Par ty Subaddress
When receiving an ISDN line station number as the Called Party Subaddress, the system
connects the call with all ISDN Terminals or Terminal Adapters (TA) on the same bus (2B
+ D).
Do the following programming:
Subaddress-Present   (See Page 89.)
Point-to-Multipoint Connection   (See Page 105.)
ISDN
ISDN Terminal
Station No. 407ISDN Terminal
Station No. 400ISDN Line
Station No. 300
ILC TRKPBX
214-555-1111
(Office No.)
300 #
(Called PartySubaddress) (Office Code 1111)
* 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 113
(3) Direct In Termination (DIT)
When the ISDN line station number is assigned as the destination of DIT, the call from ISDN
terminates all ISDN Terminals on the same bus (2B + D) simultaneously.
In addition to the programming of Point-to-Multipoint Connection on Page 105, do the
following programming:
DESCRIPTION DATA
Assign the data for DIT to the trunk num-
bers assigned by CM07.



(1)
(2)YY=02 Day Mode
YY=03 Night Mode
YY=40 Mode A
YY=41 Mode B
000-255: Trunk No. assigned by CM07 
Y=01
04: Direct-In Termination
Assign the ISDN Terminal station number 
to be terminated by Direct In Termination.



(1)
(2)YY=04 Day Mode
YY=05 Night Mode
YY=42 Mode A
YY=43 Mode B
000-255: Trunk No. assigned by CM07 
Y=01
X-XXXXXXXX: ISDN Terminal Station 
No.
ISDN
ISDN Terminal
Station No. 407ISDN Terminal
Station No. 400ISDN Line
Station No. 7880
ILC TRKPBX
214-555-7880
(Office No.)
START
CM30
END 
						

							 NEAX2000 IVS2 ISDN System ManualPage 114  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
ISDN Terminal Data Programming
(4) Station to Station Calling
When an ISDN Terminal user dials an ISDN line station number within the system, the
system connects the call with all ISDN Terminals.
Do the programming of Point-to-Multipoint Connection. See Page 105.
ISDN
ISDN Terminal
Station No. 407ISDN Terminal
Station No. 400ISDN Line
Station No. 300
ILC TRKPBX
ISDN Terminal
Station No. 417ISDN Terminal
Station No. 410ISDN Line
Station No. 301
ILC 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 115
EVENT BASED CCIS PROGRAMMING
Programming Summary
Do the system data programming for Event Based CCIS according to the procedure shown in
Figure 3-2. As for the CCIS feature programming, refer to the CCIS System Manual.
Figure 3-1 shows an outline of BRI to BRI connections.
Figure 3-1  Outline of BRI to BRI Connections
Programming for PBX A and PBX B is required on each programming procedure.
BRI TRUNKS
MATE-SIDE TRUNKS
V
O
I
C
E
CCH
HOME-SIDE TRUNKS
PBX A
BRI TRUNKS
MATE-SIDE TRUNKS
V
O
I
C
E
CCH
HOME-SIDE TRUNKS
PBX B
ISDN
NETWORK 
						

							 NEAX2000 IVS2 ISDN System ManualPage 116  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
Figure 3-2  Event Based CCIS Programming Summary
START
BRI Trunk Programming
for E-CCIS
Home Side TrunkSee Page 117.
See Page 118.
See Page 122.
Programming
Numbering Plan
Programming
BRI or PRI?
Refer to ISDN-PRI Programming 
on Page 65.PRI
BRI
Mate Side Trunk
See Page 124.
Programming
Incoming Termination
See Page 131.
Programming
Access Code/Terminating
See Page 132.
No. Assignment
Release Timer
See Page 133.
for Virtual Tie Lines
CCH Data
See Page 134.
Assignment
Tandem Connection
See Page 135.
Programming
END
Closed Numbering
See Page 136.
Plan Programming 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 117
Numbering Plan Programming
DESCRIPTION DATA
Assign station number, LCR and trunk 
route access codes.
(1)
(2)Y=0-3
X-XXXX: Access Code
801-808 : 1 to 8 digits station
A126-A129: LCR Group 0-3
100-163 : Trunk Route 00-63START
CM20
END 
						

							 NEAX2000 IVS2 ISDN System ManualPage 118  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
BRI Trunk Programming
DESCRIPTION DATA
Assign an AP number to the BRT card.
The AP number must match the SENS 
switch setting on the BRT card.
(1)
(2)Y=0
04-15, 20-31: AP No.
10: BRT card 
Assign the ISDN Protocol Type for DCH 
circuit on the BRT card. 
(1)
(2)YY=06
04-15, 20-31: AP No. of BRT assigned 
by CM05
ISDN Protocol Type
17 : Australia
18 : New Zealand
20 : AT&T (#4, #5 ESS)
21 : NTI (DMS 100, 250)
22 : Australia ETSI
24 : ETSI Standard 
(Brazil, Columbia, Indonesia)
25 : ITU-T Standard (Thailand)
27 : USA NI-1
28 : USA NI-2
63 : Not used
Assign ISDN trunk number to each 
Channel number of BRT.
NOTE:Be sure to assign the trunk 
numbers to all circuits (00-03) of 
the 2BRTC card, even if only one 
PCM digital line is accommodated 
to the card.
Set make-busy to the unused 
trunk numbers by CME5 Y=1, 2nd 
data=0.
(1)
(2)YY=02 
XX ZZ
XX: AP No. assigned by CM05
ZZ : Channel No. (00/01: BRTA)
(00-03: 2BRTC)
D000-D255: Trunk No. 
Trunk No. already 
assigned by CM10 cannot 
be used. 
Assign trunk route to each ISDN trunk 
used for Voice channel (B channel). 
NOTE:BRT route must be separated 
from analog trunk routes. 
(1)
(2)YY=00 
000-255: Trunk No. assigned by CM07 
YY=01
00-63: Trunk RouteSTART
CM05
CMAA
CM07
CM30
A
INITIAL
DTI INITIAL
INITIAL 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 119
DESCRIPTION DATA
Assign the trunk route data to each ISDN 
incoming trunk used for Voice channel 
only. 



(1)
(2)YY=02 Day Mode
YY=03 Night Mode
YY=40 Mode A
YY=41 Mode B
000-255: Trunk No. assigned by CM07 
Y=01 
18: ISDN Indial
Assign an ISDN subscriber number (last 4 
digits of telephone number) to each ISDN 
trunk.
(1)
(2)YY=19
000-255: Trunk No. assigned by CM07 
Y=01
XXXX: ISDN Subscriber No.
Assign ISDN Local Office Code Table 
number to each ISDN trunk.
(1)
(2)YY=34
000-255: Trunk No. assigned by CM07 
Y=01
00-14: Local Office Code Table No. 
Assign ISDN Local Office Code.
(1)
(2)YY=05
00-14: Local Office Table No. assigned 
by CM30 Y=34
X....X
(Max. 12 digits)
Assign the last 4 digits of telephone 
number + Service Profile ID (SPID) to 
each B channel number.
[North America Only]
(1)
(2)YY=30 
XX Z
XX: 04-15: AP No. assigned by CM05
Z : 0-3: B ch No.
XXXX ZZZZ
(Last 4 digits of tel No. + SPID: 8 digits)
Assign trunk route data to the route 
number assigned by CM30 YY=00.
(1)
(2)
(1)
(2)YY=00 Kind of Trunk Route
00-63: B channel Trunk Route No.
00: ISDN Trunk 
00-63: D channel Trunk Route No.
15 : Not used

(1)
(2)
(1)
(2)YY=04 Answer signal from distant 
office 
00-63: B channel Trunk Route No. 
2: Answer signal arrives (ISDN Trunk) 
00-63: D channel Trunk Route No.
7 : Not used
CM30
A
CM35
CM50
CMAC
B