NEC Neax 2000 Ivs2 Isdn System Manual

							 NEAX2000 IVS2 ISDN System ManualPage 130  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
• To connect the ISDN line for the voice channel after the called party answers, do the
following programming.
By the following programming, the ISDN line for the voice channel is not connected, until the
called par ty answers, or when the called par ty does not answers the call.
NOTE:This feature is available only for the connection between the NEAX2000 IVS
2/7400ICS
M100MX’s. The same programming must be set on the opposite office.
DESCRIPTION DATA
Specify the ISDN answer signal sending 
timing as “when the called party answers”.•
(1)
(2)YYY=153
00-63: Trunk Route No. of Mate-Side
Trunk for voice channels
0: Send when the called party answers
Specify the kind of the Information Transfer 
Capability of voice channel trunk route as 
“Speech”.
(1)
(2)YYY=154
00-63: Trunk Route No. of Mate-Side
Trunk for voice channels
6: Speech
CM35
END
START 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 131
Incoming Termination for Event Based CCIS Calls
DESCRIPTION DATA
Assign the Number Conversion Block No.•
(1)
(2)YY=00
X-XXXX: DID No.
000-999: Number Conversion Block 
No. 0-999
Conver t received digits to Mate-Side 
trunks.



(1)
(2)YY=01 Day Mode
YY=02 Night Mode
YY=03 Mode A
YY=04 Mode B
000-999: Number Conversion Block 
No. assigned by CM76 Y=00
BBBBB000-BBBBB255: Mate-Side
 Trunk No. of 
Virtual TrunkSTART
CM76
END 
						

							 NEAX2000 IVS2 ISDN System ManualPage 132  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
Access Code/Terminating Number Assignment 
for Outgoing Event Based Calls
DESCRIPTION DATA
Allocate memory to store the terminating 
numbers to the opposite office. (1)
(2)66
XXX YYY
XXX: 000-299: First Memory Slot No.
YYY: 001-016: Number of Memory Slot 
allocated
Assign terminating numbers of the 
opposite office (access code for ISDN line 
+ ISDN subscriber number) to the Memory 
Slot number allocated by CM71.
(1)
(2)Y=0
000-299: Memory Slot No. 
Stored No.: XX + , + ZZZ...
XX : Access Code for ISDN
ZZZ...: ISDN Subscriber No. of Oppo-
site Office (Max. 26 digits)START
CM71
END
CM72 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 133
Release Timer for Virtual Tie Lines 
(Home-Side and Mate-Side Trunks)
DESCRIPTION DATA
Specify the release timer for voice 
channels of virtual tie line. If there are no 
calls for predetermined time, the voice 
channels used for Event Based CCIS is 
released.
(1)
(2)Y=0
87: Virtual Tie Line Release Timer
    for Voice Channels
02: 2.4-4.8 sec. (2.4 sec. increments)
30: 69.6-72.0 sec.
32: 24 sec. (24 sec. increments)
70: 936 sec.
72: 1 min. (1 min. increments)
99: 28 min.
NONE : 3 min.
(Error span: 2.4 sec.)
Specify the release timer for CCH channel 
of virtual tie line. If all the voice channels 
are released and there are no calls for 
predetermined time, the CCH channel 
used for Event Based CCIS is released.
(1)
(2)Y=0
89: Virtual Tie Line Release Timer
for Common Signaling Channel
02: 2.4-4.8 sec. (2.4 sec. increments)
30: 69.6-72.0 sec.
32: 24 sec. (24 sec. increments)
70: 936 sec.
72: 1 min. (1 min. increments)
99: 28 min.
NONE : 3 min.
(Error span: 2.4 sec.)START
CM41
END
~ ~
~ ~
~ ~
~
~
~ ~
~ ~ 
						

							 NEAX2000 IVS2 ISDN System ManualPage 134  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
CCH Data Assignment 
DESCRIPTION DATA
Assign an AP number to the CCH card 
(PN-SC00).
The AP number must match the SENSE 
switch setting on the CCH card.
(1)
(2)Y=0
04-15, 20-31: AP No.
11: CCH Card
Assign a CCH channel number to each 
CCH card.
(1)
(2)YY=07
0-7: CCH channel No.
04-15, 20-31: AP No. of CCH Card
Assign the trunk number used as the 
common signaling channel.
(1)
(2)YY=00
0-7: CCH channel No.
000-255: Trunk No. assigned by CM07
Assign an Originating Point Code (OPC) of 
own office and Destination Point Code 
(DPC) of opposite office, to each CCH 
channel.
NOTE:The OPC is used to designate an 
originating office in the No. 7 CCIS 
network. A single OPC of own 
office should be assigned to all 
CCH channels provided in the 
same system.
(1)
(2)

(1)
(2)YY=01
0-7: CCH channel No.
00001-16367: OPC
YY=02
0-7: CCH channel No.
00001-16367: DPC
Assign ACM signal waiting timer.
(1)
(2)YY=10
0-7: CCH channel No.
14: 28 sec.
Assign CCH channel to which a signaling 
message is transferred according to the 
Destination Point Code (DPC) received.(1)
(2)00001-16367: DPC
0-7: CCH channel No.
CM06 START
CM05
CMA8
END
CMA7
INITIAL
INITIAL 
						

							CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 135
Tandem Connection Programming
 When providing Tandem Connection (ISDN to CCIS/CCIS to ISDN), do the following
programming:
DESCRIPTION DATA
 Specify the combination of trunk routes 
allowing the tandem connection.
NOTE:The Home-Side Virtual Tie line 
routes must be included for all 
Tandem combinations.
(1)
(2)Y=0
XX ZZ
XX: 00-63: Incoming Trunk Route
ZZ: 00-63: Outgoing Trunk Route
0 : Allowed
1: Restricted
Tandem connection by station or 
attendant.(1)
(2)028
0 : Available
1 : Not availableSTART
CM36
END
CM08 
						

							 NEAX2000 IVS2 ISDN System ManualPage 136  ND-70919 (E), Issue 1.0
CHAPTER 3  SYSTEM DATA PROGRAMMING
Event Based CCIS Programming
Closed Numbering Plan Programming
DESCRIPTION DATA
Assign LCR Group number to Area Code 
Development Pattern.
(1)
(2)YYYY=A000
0-3: LCR Group No.
4000-4007: Area Code Development 
Pattern No.
Assign Area Code Development Pattern 
number.
(1)
(2)YYYY=4000-4007
X...XXX: Area Code (Max. 8 digits)
0000-0255: Route Pattern No.
Assign Route Pattern.
(1)
(2)YYYY=0000-0255
1-4: 1st-4th Order
XXX ZZ
XXX: 000-255: LCR/TR Pattern No.
ZZ :
 00-63: Trunk Route No.
 
Assign maximum number of sending 
digits.
(1)
(2)Y=0-7 Area Code Development Pattern 
No. 0-7
X...XX: Area Code (Max. 8 digits)
01-79: Max number of sending digits
START
CM8A
END
CM85 
						

							NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 137
CHAPTER 4
CIRCUIT CARD 
INFORMATION
This chapter explains the mounting location, the meaning of lamp
indications, and the method of switch settings of each circuit card for
the ISDN system. 
						

							 NEAX2000 IVS2 ISDN System ManualPage 138  ND-70919 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
How to Read This Chapter
HOW TO READ THIS CHAPTER
This chapter explains each circuit card used in this system. Explanations are given in
alphabetical order of the circuit card names within each circuit card category (Control,
Application Processor, and Line/Trunk).
(1) Locations of Lamps, Switches, and Connectors
The locations of lamps, switches, and connectors of each circuit card are shown by a face 
layout.
(2) Lamp Indications
The name, color, and functions of each indicator lamp equipped on each circuit card are 
described in a table.
(3) Switch Settings
The name, settings, and functions of each switch equipped on each circuit card are 
described in a table.
Each switch setting table has a CHECK column. Make necessary entries in the CHECK column
during and/or after the system installation and maintenance, and use each table as a reference
for subsequent system maintenance and operations. 
						

							CHAPTER 4  CIRCUIT CARD INFORMATION
Mounting Location of Circuit Card
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 139
MOUNTING LOCATION OF CIRCUIT CARD
This section explains the conditions for mounting circuit cards for the ISDN system. Figure 4-1
shows circuit card mounting slots allocated in the PIM.
Figure 4-1  Mounting Location of Circuit Card
*1: PN-CP14 (MP) card on the MP12 slot on PIM0.
*2: The following application processor cards can be mounted in the AP00-AP11 slots on
PIM0-7.
PN-BRTA (BRT)
PN-2BRTC (BRT)
PN-24DTA-C (DTI)
PN-30DTC-A (DTI)
PN-24PRTA (PRT)
PN-SC00 (CCH)
PN-SC01 (DCH)
PN-SC03 (ICH)
*3: PN-ILCA (ILC) card on the LT00-LT07 slots on PIM0-7.
*4: PZ-M542/PZ-M557 (CONN) card on the LTC0-LTC3 connectors on the PIM which
accommodates 30 DTI card.
LT09/AP09LT08/AP08LT07/AP07
LTC1LTC0LTC2
BWB
PIM
0~7
FRONTAC/DC
PWR
LT10/AP10LT00/AP00LT01/AP01LT02/AP02LT03/AP03LT04/AP04LT05/AP05LT06/AP06LT11/AP11/FP11MP12/FP12
LTC3
DC/DC
PWR
PFTVM
*2*1
 *3
*4