NEC Neax 2000 Ivs2 Isdn System Manual

							 NEAX2000 IVS2 ISDN System ManualPage 140  ND-70919 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
List of Required Circuit Cards
LIST OF REQUIRED CIRCUIT CARDS
Table 4-1 shows the required circuit cards that are explained in this section.
* MB = Make Busy
Table 4-1  List of Required Circuit Card
NAME
(FUNCTIONAL
NAME)
LAMP
X: PROVIDED
–: NOT 
PROVIDEDSWITCH
X: PROVIDED
–: NOT 
PROVIDEDEXTRACTION/
INSERTION WITH 
POWER ON
X: ALLOWED
: ALLOWED 
AFTER MB*
–: NOT ALLOWEDREFERENCE
PAGE
PN-CP14 (MP) X X –Page 141
PN-BRTA (BRT) X XPage 146
PN-2BRTC (BRT) X XPage 151
PN-24DTA-C 
(DTI)XXPage 156
PN-30DTC-A 
(DTI)XXPage 162
PN-24PRTA 
(PRT)XXPage 168
PN-SC00 (CCH) X XPage 174
PN-SC01 (DCH) X XPage 177
PN-SC03 (ICH) X XPage 180
PZ-M542 (CONN) – X XPage 182
PZ-M557 (CONN) – X XPage 184
PN-2ILCA (ILC) X X XPage 186 
						

							CHAPTER 4  CIRCUIT CARD INFORMATION
PN-CP14 (MP)
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 141
PN-CP14 (MP)
Locations of Lamps, Switches, and Connectors
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally
CLK Green Remains lit while receiving clock signals to the PLO
SW3
RUN
SW1
SW2
CLK
VR
DK JACK CONNSW4
JP0JP1
RS1
RS0
CONN: To CONNR connector on PZ-M537 (EXPMEM) 
						

							 NEAX2000 IVS2 ISDN System ManualPage 142  ND-70919 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-CP14 (MP)
Switch Settings
NOTE 1:Set the groove on the switch to the desired position.
NOTE 2:Only when executing MP Program Download using the Software Activation Tool in
MATWorX Studio, set the SW3 to 5-8.
CAUTION
When the operating power is being supplied to this circuit card, do not plug/unplug this circuit
card into/from its mounting slot.
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW3 (Rotary SW)
NOTE 1
0-FOn Line
(Call processing is in progress)
2 Off Line (Call processing is stopped)
I/O port: As per CM40 YY=08
3 Off Line (Call processing is stopped)
I/O port: 9600 bps (Fixed)
5
NOTE 2Off Line (Call processing is stopped)
I/O port: 9600 bps
6
NOTE 2Off Line (Call processing is stopped)
I/O port: 19200 bps
7
NOTE 2Off Line (Call processing is stopped)
I/O port: 38400 bps
8
NOTE 2Off Line (Call processing is stopped)
I/O port: 57600 bps
B For clearing the office data
C For setting the resident system 
program
1, 4, 9
A, D-FNot used
(Continued)
0
0 
						

							CHAPTER 4  CIRCUIT CARD INFORMATION
PN-CP14 (MP)
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 143
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW1 (Push SW)For initializing CPU
SW2
(Piano Key SW)1ON A-law (Australia)
OFF µ-law (North America)
2, 3Selection of PLO0 input
(Phase Locked Oscillator)
 For clock receiver office:
 For clock source office:
SW2-2
SW2-3
OFF OFF
4ONWhen using RS1 port for built-in 
MODEM
OFF When using RS1 port for RS-232C
(Continued)
4 
3 
2 
1 OFF
ONSW2-2 SW2-3 FUNCTION
OFF OFF 1.5 MHz clock
(For PN-24DTA-C/PN-24PRTA)
ON OFF 192 kHz clock
(For PN-BRTA)
OFF ON 2 MHz clock
(For PN-30DTC-A/PN-2BRTC)
ON ON Not used 
						

							 NEAX2000 IVS2 ISDN System ManualPage 144  ND-70919 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-CP14 (MP)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SW4 (DIP SW)1
Not used
2 Not used
3, 4Selection of PLO1 input
(Phase Locked Oscillator)
 For clock receiver office:
 For clock source office:
SW4-3
SW4-4
OFF OFF
VR (Rotary SW)
Variable Resistor for External Hold 
Tone Source
(0-20 Kohms: Clockwise)
DK (Connector)
02 Ground detection
01 Ground sending
(Continued)
1
23
4ON
OFF
OFF
SW4-3 SW4-4 FUNCTION
OFF OFF 1.5 MHz clock
(For PN-24DTA-C/PN-24PRTA)
ON OFF 192 kHz clock
(For PN-BRTA)
OFF ON 2 MHz clock
(For PN-30DTC-A/PN-2BRTC)
ON ON Not used
20
0
01 02 
						

							CHAPTER 4  CIRCUIT CARD INFORMATION
PN-CP14 (MP)
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 145
The figure in the SWITCH NAME column and the position in    in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and   , the setting of the switch varies with the system concerned.
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
JP0 (Jumper Pin)UPNot used
(Memory backup OFF)
For normal operation
(Memory backup ON)
JP1 (Jumper Pin)
For using internal tone source
DOWNFor using external tone source
FrontDOWN
Fr o n t
UP 
						

							 NEAX2000 IVS2 ISDN System ManualPage 146  ND-70919 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-BRTA (BRT)
PN-BRTA (BRT)
Locations of Lamps, Switches, and Connectors
SENSE
RUN
MB
SW1
SW0B1
B2
D
ALM 
						

							CHAPTER 4  CIRCUIT CARD INFORMATION
PN-BRTA (BRT)
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 147
Lamp Indications
LAMP 
NAMECOLOR FUNCTION
RUN Green Flashes at 120 IPM while this card is operating normally
B1 Green B1 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):  Make Busy
B2 Green B2 channel status
ON: Busy
OFF: Idle
Flash (60 IPM):  Make Busy
D Green D channel status
ON: Busy
OFF: Idle
ALM Red Transmission line fault status
ON: Line fault
OFF: Normal operation 
						

							 NEAX2000 IVS2 ISDN System ManualPage 148  ND-70919 (E), Issue 1.0
CHAPTER 4  CIRCUIT CARD INFORMATION
PN-BRTA (BRT)
Switch Settings
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
SENS
(Rotary SW)
NOTE 14-F Set the switch to match the AP Number (04-15) to
be set by CM05.
0-3 Not used
MB (Toggle SW)
NOTE 2
UP For make-busy
For normal operation
SW0 (DIP SW)
1For normal operation 
OFF Not used
2
NOTE 3
NOTE 4ONSource clock signal from network is 
sent to the PLO of MP according to 
the switch setting of SW0-3.
OFFSource clock signal from network is 
not sent to the PLO of MP card.
3
NOTE 3
NOTE 4ONClock signal is sent to the PLO0 of 
MP.
OFFClock signal is sent to the PLO1 of 
MP.
4For normal operation
OFF Not used
(Continued)
AP No.04 05 06 07 08 09 10 11 12 13 14 15
SW No.456789ABCDEF
ON
DOWN
1
23
4ON
ON
ON 
						

							CHAPTER 4  CIRCUIT CARD INFORMATION
PN-BRTA (BRT)
NEAX2000 IVS2 ISDN System Manual    
ND-70919 (E), Issue 1.0   Page 149
The figure in the SWITCH NAME column and the position in   in the SETTING POSITION
column indicate the standard setting of the switch. When the switch is not set as shown by the
figure and  , the setting of the switch varies with the system concerned.
NOTE 1:Set the groove on the switch to the desired position.
NOTE 2:When the power is on, flip the MB switch to ON (UP position) before plugging/
unplugging the circuit card. SW1 (DIP SW)
1For terminating the transmitting side 
of channels B1 and B2 with 100 
ohms
OFFTo remove the terminating resistor 
on the transmitting side of channels 
B1 and B2
2For terminating the receiving side of 
channels B1 and B2 with 100 ohms
OFFTo remove the terminating resistor 
on the receiving side of channels B1 
and B2
(Continued)
SWITCH NAMESWITCH 
NUMBERSETTING 
POSITIONFUNCTION CHECK
1
2ONON
ON