NEC Neax 2000 Ivs Wcs System Manual

							ND-46248 (E) CHAPTER 4
Addendum-001 Page 157
MARCH, 1999 Revision 2.1
SYSTEM DATA PROGRAMMING
3.7.4 Visitor PS Data Assignment
DESCRIPTION DATA
Execute System Data Memory All Clear of the
DBM (AP00) card.
The System Data Memory All Clear must be
done at the initial setup.
This data is valid when the DBM card is on-
line.•
(1)
(2)YYY=999
1 (All Clear)
CCC
Execute Work Memory All Clear of the DBM
card.
The Work Memory All Clear must be done be-
fore the system starts operating. All HLR,
VLR data is cleared by this command.
This data is valid when the DBM card is on-
line.
(1)
(2)YYY=998
1 (All Clear)
CCC
Assign the Home PBX ID of Visitor PS and its
data table number.
This data is used to define the PBX for which
the PS can perform Roaming.
This data is valid when the DBM card is on-
line.
(1)
(2)YYY=000
X-XXXX: Home PBX ID
(1-4 digits, Decimal)
000-255: Data Table No.
CCC: Data Clear
NONE
 
Assign the Home PBX ID of Visitor PS and its
data table number.
This data is used to define the route used for
registration of the PS location.
This data is valid when the DBM card is on-
line.
(1)
(2)YYY=001
000-255: Data Table No. assigned by 
CMAF YYY=000
00-07: Route Selection Pattern No.
CCC: Data Clear
NONE 
START
CMAF
A 
						

							CHAPTER 4 ND-46248 (E)
Page 158 Addendum-001
Revision 2.1 MARCH, 1999
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the Trunk Route to be used for request-
ing the data of the Visitor PS against its Home
PBX.
This data is valid when the DBM card is on-
line.
(1)
(2)YYY=100-107 (Route Selection Pattern 
No. 00-07)
1-4: First-Fourth Selected Route
00-63: Q931a D Channel Trunk Route No.
NONE  : No Data
CCC: No Data Clear
Assign the Default restriction class for Visitor
PS.
Note:This data must be assigned. The
Roaming will not work properly
if the second data is set to
Default (NONE). It must be set to
any value from 01 to 08.
(1)
(2)YYY=002
000-255 (Data table No. Assigned by 
CMAF YYY=000
01-08 (Default restriction class of Visitor 
PS.
NONE  : No Data (Default)
Assign the Virtual Line/Trunk Circuit Number
for the Visitor PS to the required LEN.
Note 1:Be sure to assign the Station No.
to the Level 1 and Level 3.
Be sure to assign the Trunk No.
to the Level 0 and Level 2.
Note 2:The Virtual Line/Trunk Circuit
No. must be assigned from the
last LEN No. 0511.(1)
(2)0000-0511: LEN
X-XXXX: Virtual Station No.
D000-D255: Virtual Trunk No.
NONE  : No Data
Assign an access code for LCR Group 0-3 if
necessary.
(1)
(2)Y=0-3 (Numbering Plan 0-3)
X-XXXX: Access Code
A26: LCR Group 0
A27: LCR Group 1
A28: LCR Group 2
A29: LCR Group 3
Specify the path between the Virtual Line and
Trunk assigned by CM10.
This data is used to define the route used for
registration of the PS position.
This data is valid when the DBM card is on-
line.
Note:Combination must be as follows:
• Level 0 Trunk No. and Level 1
Station No.
Level 2 Trunk No. and Level 3
Station No.
(1)
(2)YY=00
000-169: Block No.
DXXX (Virtual Trunk No. 000-255) +   + 
X-XXXX (Virtual Station No.) 
NONE  : No Data
CMAF
CM10
CM20
CM5A
CMAF
,
A
B 
						

							ND-46248 (E) CHAPTER 4
Pag e 15 9
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the telephone set type of Virtual LC 
for the Visitor PS as 10 PPS.
(1)
(2)YY=00
X-XXXX: Virtual LC Station No.
1: 10 PPS
Assign the Service Restriction Class of the 
Virtual LC for the Visitor PS.
Assign the different class to the Virtual LC for 
Visitor PSs from the station and Home PS of 
the PBX.
(1)
(2)YY=02
X-XXXX: Virtual LC Station No.
XXYY
XX: Service Restriction Class A
(00-15 )
YY: Service Restriction Class B
(00-15 )
Assign the Service Restriction Class C of the 
Virtual LC for the Visitor PS.
(1)
(2)YY=07
X-XXXX: Virtual LC Station No.
00-15  : Service Restriction Class C
Validate answer signals to the Virtual LC for 
the Visitor PS.
(1)
(2)YY=18
X-XXXX: Virtual LC Station No.
0: Valid
Allow the Virtual LC for the Visitor PS to use 
Roaming.
(1)
(2)YY=39
X-XXXX: Virtual LC Station No.
0: Available
1 : Not available
For the Virtual LC for the Visitor PS, restrict 
the station service data of CM15 YY=00-48.
(1)
(2)YY=00, 02, 03, 10, 11, 12, 13, 15, 16, 19, 
22, 26, 27, 28, 29, 40, 44, 47, 48.
00-15 (Service Restriction Class A)
0: RestrictedCM12
B
C
CM13
CM15 
						

							CHAPTER 4 ND-46248 (E)
Pag e 16 0
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign a Trunk Route to each trunk number 
used for Virtual COT for the Visitor PS.
Make a separate route from other trunk routes.
(1)
(2)YY=00
Trunk No. (000-255)
Trunk Route No. (00-63)
Assign the terminating system to the Virtual 
COT as “Roaming Termination”.
(1)
(2)YY=02 (Day Mode)
YY=03 (Night Mode)
Trunk No. (000-255)
22: Roaming Termination
Assign trunk route data to the Virtual COT 
route number for the visitor PS assigned by 
CM30 YY=00.
(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)YY=00 (Kind of Trunk Route)
Route No. (00-63)
00: ISDN/C.O. Trunk
YY=01 (Dialing Signal Type)
Route No. (00-63)
4: Call Termination; DTMF
Call Origination; DTMF
7  : Call Termination; DP/DTMF
Call Origination; DTMF
YY=04 (Answer Signal from Distant
Office)
Route No. (00-63)
1: Answer Signal arrives (C.O.)
YY=05 (Release Signal from Distant
Office)
Route No. (00-63)
1 : Release signal arrives
YY=14 (SMDR for Outgoing Call)
Route No. (00-63)
0/1 : Not to be provided/To be provided
YYY=139 (Roaming)
Route No. (00-63)
0: AvailableCM30
CM35
C
D 
						

							ND-46248 (E) CHAPTER 4
Addendum-001 Page 161
MARCH, 1999 Revision 2.1
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the Route Selection Pattern Number 
as “Pattern Number 0”, for all classes of the 
Trunk Restriction Class (01-06) sent from the 
Home PBX.
This data is valid when the DBM card is on-
line.
(1)
(2)YYY=208
01-06: Trunk Restriction Class sent from 
the Home PBX
00: Route Selection Pattern 0
Specify the Virtual COT Trunk route to be 
used for originating/terminating calls from/to 
the Visitor PS.
This data is valid when the DBM card is on-
line.
(1)
(2)YYY=200
(Route Selection Pattern 0)
1: First Selected Route
00-63: Trunk Route
NONE  : No Data
Assign the Station Hunting Group of the virtu-
al LCs for the Visitor PSs.
All the Virtual LC Stations in one Hunting 
Group must be the Virtual LC Station corre-
sponds to the Virtual COTs for which the same 
Trunk Route is assigned.
(1)
(2)Y=0
X-XXXX: Virtual LC Station No.
X-XXXX: Virtual LC Station No.
Specify the kind of station for a Virtual LC 
Station as a Pilot Station, and for other Virtual 
LC stations as a Member Station.
(1)
(2)Y=1
X-XXXX: Virtual LC Station No.
0: Member Station
1 : Pilot Station
Assign the Roaming Station Number for the 
Visitor PS. For the Roaming Station Number, 
set the Virtual LC Pilot Station Number spec-
ified by CM18 Y=1.
This data is valid when the DBM card is on-
line.
(1)
(2)YYY=210
00 (Roaming Number Assignment)
X-XXXX: Roaming Station NumberCMAF
E
CM18
CMAF
D 
						

							CHAPTER 4 ND-46248 (E)
Pag e 16 2
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Provide the Visitor PS with the capability to 
enter an Account Code, if required.
(1)
(2)YY=30
00-15 (Service Restriction Class A
assigned by CM12 YY=02)
0: Restricted
1 : Allowed
Specify the maximum number of Account 
Code.(1)
(2)10 (Max. Digits for Account Code)
01-16 : 01-16 digitsCM15
E
CM42
END 
						

							ND-46248 (E) CHAPTER 4
Pag e 16 3
Revision 2.0
SYSTEM DATA PROGRAMMING
3.8 Maintenance Data Assignment
DESCRIPTION DATA
Assign the registration of fault information 
into Memory and the control of the external 
alarm.
(1)
(2)Y=2 
12:  ZT fault occurred (Not recovered)
2B:  ZT fault occurred
3B:  ZT fault recovered
0:  Registration of Fault Memory/No out-
put of External alarm
1:  Registration of Fault Memory
/External alarm is MN alarm
2:  Registration of Fault Memory
/External alarm is MJ alarm
NONE  :  No Registration of Fault 
Memory/No output of 
External alarm
DESCRIPTION DATA
When changing the ZT data (CM10, CM06, 
CMAD YY=00) in service, make busy the ZT.
(1)
(2)Y=3 
ZT No. (000 ~ 255)
2: Make busy after calls finished.
CMEA
END
START


CME5
END
START 
						

							CHAPTER 4 ND-46248 (E)
Pag e 16 4
Revision 2.0
SYSTEM DATA PROGRAMMING
3.9 Maintenance Administration Terminal (MAT)
The figures below describe the installation for the WCS Maintenance Administration Terminal (MAT). For
more information about system-required equipment, system description and MAT Operation, refer to your MAT
Operation Guide.
3.9.1 Direct Connection
Figure 4-1    Cable Connection (Direct)
Table 4-1  MAT Cable (Direct)
DESCRIPTION QUANTITY REMARKS
MAT CA-Q 1/Sys RS-232C Cable, 13.1 ft. (4.0 m)
RSM
P PIM0
MAT CA-Q, 13.1 ft. (4 m)25p DSUB(F)
RS-232C cable (PC)
(Max. 36.1 ft. (11 m))MAT 
						

							ND-46248 (E) CHAPTER 4
Pag e 16 5
Revision 2.0
SYSTEM DATA PROGRAMMING
3.9.2 Remote Connection
Remote connection is available via an internal modem in the MP or an external modem.
Remote Connection via Internal Modem
Figure 4-2    MAT Cable Connection (Remote Connection via Internal Modem)
Note 1:
The Installation Cable is connected to LTC0, LTC1, or LTC2 connector depending on the installed loc-
tion of the COT card.
Note 2:The MP to COT connection is made through internal switching of the Time Division Switch.
Remote Connection via External Modem
Figure 4-3    MAT Cable Connection (Remote Connection via Modem)
Table 4-2  MAT Cable (Remote Connection)
DESCRIPTION QUANTITY REMARKS
RS NORM-4S CA-A 1/MAT RS-232C Cable, 13.1 ft. (4.0 m)
PIM0
M
PInstallation Cable
LT C 0MDF
MATC
O
T
MODEM PSTN
PIM0
M
P25p DSUB (M)
MODEMMDF
MAT RS NORM-4S CA-A
13.1 ft. (4 m)
PSTN
MODEM 
						

							CHAPTER 4 ND-46248 (E)
Pag e 16 6
Revision 2.0
SYSTEM DATA PROGRAMMING
4. DATA PROGRAMMING SHEETS
This section provides the sheets of WCS data, on a command basis. Complete the blank with data assigned. The
following symbol with the meaning indicated below is used within the data sheets.
: System Initialization
After data setting, system initialization is required by the SW1 switch on the MP card.
INITIAL