NEC Neax 2000 Ivs Wcs System Manual
Have a look at the manual NEC Neax 2000 Ivs Wcs System Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ND-46248 (E) CHAPTER 3 Page 81 Revision 2.0 INSTALLATION CAUTION Battery Replacement Table and Battery Warnings The label which shows battery replacement table and battery warnings is attached to the reverse side of Front Cover for PIM, BATTM and PWRM. During the battery installation process, the warning statements must be observed. When replacing batteries, the battery replacement table should be observed in order to increase battery life and insure a safe operation. 25 ~ 30°C 2.0 ~ 2.5 (77 ~ 86°F) LABEL PIM/BATTM/PWRM FRONT COVER BATTERY REPLACEMENT TABLE INSTALLATION DATE: , . AMBIENT TEMPERATURELESS THAN 25°C (77°F) REPLACEMENT INTERVAL2.5 ~ 3.0 1.5 ~ 2.0CAUTIONTO PREVENT INJURY AND SKIN BURN, PAY ATTENTION TO THE FOLLOWING. o DO NOT STRIKE A MATCH OR CAUSE A SPARK IN VICINITY OF BATTERY. o PLACE THE EQUIPMENT WELL VENTILATED AREA. o DO NOT SHORT. o REPLACE BATTERY ONLY AFTER BATTERY GASES HAVE BEEN DISPERSED. o ELECTROLYTE LEAKAGE OR OTHER HAZARDS MAY RESULT IF THE BATTERY IS NOT REPLACED IN ACCORDANCE WITH THE SPECIFIED INTER- VALS. (86 ~ 104°F) 30 ~ 40°C YEARS YEARS YEARS
CHAPTER 3 ND-46248 (E) Pag e 82 Revision 2.0 INSTALLATION4.11.1 Internal Battery Connection STEP 1: Mount th e t wo b atte ries (1 2V DC, 3. 0–3 .4 A H f o r PW 86 c ard ) in to e a ch P IM as s h ow n in F ig u re 3- 3 5. Figure 3-35 Internal Battery Mounting (1 of 2) Note: The two 2/12V batteries do not backup power feeding 2Ts, which can be backed up by adding 48V bat- tery. See Section 4.11.2. FRONT W 67 mm DIMENSION OF BATTERY BATTERY UNIT (2 × 12VDC, 3.0 to 3.4AH) (2.6 inch) L 134mm(5.3 inch) H 60 mm (2.4 inch) BASE PWRM PIM FG N EU T R AL L IN E Blue Red Black
ND-46248 (E) CHAPTER 3Page 83 Revision 2.0 INSTALLATION Figure 3-35 Internal Battery Mounting (2 of 2) Note: The two (2) 12V batteries do not backup power feeding ZTs, which can be backed up by adding 48V b atter y. See Se ction 4 .11.2 . FRONT W 34 mm DIMENSION OF BATTERY BATTERY UNIT (2 × 12V DC, 2.6AH) (1.3 inch) L 178 mm(7.1 inch) H 60 mm (2.4 inch) PIM Blue Red Pin # 4 Pin # 1 NEAX1000 IVS Recommended Battery GS type PX12026 Black
CHAPTER 3 ND-46248 (E) Pag e 84 Revision 2.0 INSTALLATION STEP 2: Plug the b atte ry ca ble c onn ec tor in to the B ATT1 con nec tor o n the P W 86 ca rd as sh ow n in Fig ure 3- 3 6. STEP 3: Secu re the batt e rie s and b atte ry c ab le u sing t ie w raps as sh ow n in Figu re 3 -36 . Figure 3-36 Internal Battery Connection PLUG IN TO BATT 1 CONNECTOR ON PZ-PW86 FRONT TIE WRAP PIM BATTERY CABLE
ND-46248 (E) CHAPTER 3Page 85 Revision 2.0 INSTALLATION STEP 4: When the system is a multiple PIM configuration, plug the PWR CA-A into the BATT2 connector on the PW 86 ca rd as s how n in Fig ure 3-37. Figure 3-37 Internal Battery Connection for a Multiple PIM Configuration PWR CA-A BATT2 BATT1 PW86 –+–+ PIM3 BATT2 BATT1 PW86 –+–+ PIM2 BATT2 BATT1 PW86 –+–+ PIM1 BATT2 BATT1 PW86 –+–+ PIM0 BATTERY CABLE BATT2 BATT1 PW86 –+–+ PIM7 BATT2 BATT1 PW86 –+–+ PIM6 BATT2 BATT1 PW86 –+–+ PIM5 BATT2 BATT1 PW86 –+–+ PIM4 BATTERY CABLE PWR CA-A PWR CA-A PWR CA-A Blue Red
CHAPTER 3 ND-46248 (E) Pag e 86 Revision 2.0 INSTALLATION Figure 3-38 PWR CA-A 550 mm (21.7 inch) PWR CA-A
ND-46248 (E) CHAPTER 3 Addendum-001 Page 87 MARCH, 1999 Revision 2.1 INSTALLATION 4.11.2 Battery Connection in PWRM When the system is equipped with one or two PW91 card, the battery for PW91 card can be mounted into the Power Module (PWRM). When the system is equipped with more than two PW91 card, refer to Section 4.11.3. Note:A 48V battery (4x12 VDC) is required to back up PW91 for ZT power feeding. STEP 1: Connect the battery cables to the batteries as shown in Figure 3-39. Figure 3-39 Battery Connection into PWRM Recommended Battery Yuasa NP7-12 Specifications UL Listed 12VDC, 7AH Terminal : Fasten Tab type Dimensions : 151 mm L x 65 mm W x 94 mm H (59.4 in. L x 25.6 in. W x 37 in. H) Into PWRM BATTERY CABLE BATTERY UNIT (4 X 12VDC, 7AH) RED BLUE
CHAPTER 3 ND-46248 (E) Pag e 88 Revision 2.0 INSTALLATION STEP 2: Secu re t he B atte ry Br ac k et a nd t o th e PW RM as sh ow n in Figu re 3-40 . STEP 3: Mount t he batte ry u nit ( 4 x12 VDC, 7A H per un it) i n to the P W RM as sh ow n in Figu re 3-40 . STEP 4: Secu re t he B atte ry Br ac k et to the PW RM as sh ow n in Figu re 3 -40 . Figure 3-40 Battery Mounting into PWRM 12 3 BATTERY BRACKET 1BATTERY UNIT (4x12 VDC, 7AH) BATTERY BRACKET 3 BATTERY BRACKET 2 BATTERY BRACKET3 PWRM
ND-46248 (E) CHAPTER 3Page 89 Revision 2.0 INSTALLATION STEP 5: Plug the b atte ry ca ble c onn ec tor in to the B ATT2 con nec tor o n the P W 91 ca rd as sh ow n in Fig ure 3- 4 1. STEP 6: Co nne ct the PW91 ca rd s to each o ther us ing the P W R CA -A as sh ow n in Figu re 3 -41 . Figure 3-41 Battery Connection in PWRM PWRM PW91 BATT2 BATT1PW91 BATT2 BATT1 PWR CA-A BATTERY UNIT (48VDC, 7AH) BATTERY CABLE
CHAPTER 3 ND-46248 (E) Pag e 90 Revision 2.0 INSTALLATION4.11.3 Battery Connection in BATTM 1. For PW86 card (-24 V DC) STEP 1: Connect the battery cables to the batteries, and mount the battery units (2 ×12 V DC, 24AH per unit) i n to t he Ba tt e ry M odule ( B ATTM) as sh ow n in Figur es 3-42 and 3-4 3. Figure 3-42 Battery Mounting into BATTM for PW86 Card Recommended Batteries GS Portalac PE12V 24ABI Yuasa NP24-12B Specifications UL Listed 12V DC, 24AH Terminal: bolt/nut type with hole for 5mm bolt Dimensions:175 mm L × 166 mm W × 125 mm H (6.89 in L × 6.54 in W × 4.92 in H) A: 12 mm 5.5 mm B: 2 mm (.216 in) (.472 in) (.079 in) Pin # 4 BATTERY CABLE BATTM BATTERY UNIT (2x12 V DC, 24AH) BATTERY UNIT (2x12 V DC, 24AH) FRONT TO PW86 CARD IN PIM0/PIM4Blue Red Black Pin # 1