NEC Neax 2000 Ivs Wcs System Manual

							ND-46248 (E) CHAPTER 4
Pag e 11 9
Revision 2.0
SYSTEM DATA PROGRAMMING
3.2 ZT Set Up
3.2.1 Initial Set Up of ZT
Do the following procedure to set up the ZT.
Note:When reinstalling the system after power down exceeding 8 hours, the System ID will be cleared. Re-
entry of the System ID must be required.
START
Assignment of ZT dataSee Section 3.1.
Call NTAC
G1, G2.
ZT Authorization
SYS ID AssignmentAssignment of
LVP Code
END
or Enter the 
LVP code
ZT AuthorizationNTAC LVP
Mat Worx 32
Please call NTAC (NECAM National Technical Center)
for this data assignment. Action by Maintenance Person :
: 
						

							CHAPTER 4 ND-46248 (E)
Pag e 12 0
Revision 2.0
SYSTEM DATA PROGRAMMING
3.2.2 Setting Up of Additional ZT
Do the following procedure to add the ZT.
START
Assignment of ZT data
ZT Authorization
END
See Section 3.1.
See MAT mode MENU in COM04,
G2. ZT Authorization.
Please call NTAC (NECAM National Technical Center)
for this data assignment. Action by Maintenance Person :
: 
						

							ND-46248 (E) CHAPTER 4
Pag e 12 1
Revision 2.0
SYSTEM DATA PROGRAMMING
3.3 PS Data Assignment
Proceed with the following procedure after SYS ID Assignment and ZT Authorization by NTAC.
DESCRIPTION DATA
Assign a PS Station No. to the required virtual 
PS No.(1)
(2)Virtual PS No. (0001 ~ 0255)
X-XXXX: PS Station No. (X=0-9, *, #)
Assign a PS-ID.
(Primary PS Station only)
Note 1:Insert leading zeroes in the PS-
ID for a mzximum of nine digits.
For example, if PS ID is 1234,
enter 000001234 as the PS-ID.
Note 2:When a PS is assigned as a sub-
line (second line), this data
should not be assigned and must
be set to default “NONE”.
See Section 3.6.6 for multi-line operation PS 
programming.
(1)
(2)YY = 21
X-XXXX: PS Station No.
XX···XX: PS-ID (Max. 9 digits, Deci-
mal)Note:PS-ID as shown inside the
battery compartment of
your PS.
For the D
term PS II, Specify the terminal kind 
of the PS as “Dterm PS II”.
Set this data also to the Sub-line PS station 
number, if provided.
(1)
(2)YY=15
X-XXXX: PS Station No./Sub-line PS 
Station No.
00 : D
term PS II
15 : Former Dterm PS
Assign the sub-line PS number to each prima-
ry PS station.
(1)
(2)YY=01
X-XXXX: Primary PS Station No.
X-XXXX: Sub-line PS Station No.
START
CM1C
CM1D
A

 
						

							CHAPTER 4 ND-46248 (E)
Page 122 Addendum-001
Revision 2.1 MARCH, 1999
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the Service Restriction Class to each 
PS station.•
(1)
(2)YY=02 
X-XXXX: PS Station No.
XX
 XX
Service Restriction Class A 
(00-15 )
When providing Roaming Service, specify the 
Service Restriction Class for Roaming Service 
data down load.
Note 1:Assign the same Service
Restriction Class data to the PS
station number and the Virtual
LC Station number (see section
3.7.4) for Roaming Service.
Note 2:When the roaming service is
provided, in the system where the
second line service is also
provided, it is recommended to
set the primary PS-stations in
different service restriction class
than sub-lines, since sub-lines do
not support the roaming feature.
(1)
(2)YYY=117
00-15: Service Restriction Class A assigned 
by CM12 YY=02
0: Allowed
1 : Restricted
When providing Roaming Service, assign the 
Home PBX ID of the PBX to which the PS 
belongs. Assign the same number with the 
first 4 digits of the Individual PS Number.
(1)
(2)YY=00
04 (Assignment of Home PBX ID)
X-XXXX: Home PBX ID
(1-4 digits, Decimal)
CM12
B
A
CM15
CMAE

 
 
						

							ND-46248 (E) CHAPTER 4
Addendum-001 Page 123
MARCH, 1999 Revision 2.1
SYSTEM DATA PROGRAMMING
When changing the PS operation data
If you change the PS operation data in this section already downloaded to a PS, repeat PS data download (CM1D 
YY=20 second data: 1).
DESCRIPTION DATA
Download the PS operation data to each PS by 
assigning the 2nd data 1.
Note 1:All steps for setting up ZTs and
all wiring must be successfully
completed and ZTs must be idle
before downloading PS
operation data.
Note 2:When a PS is set up initially, set
the PS in Data Download Mode
by applying power to the PS
while pressing the SEND key,
and then execute the CM1D
YY=20 in Calling Area No. 00.
Note 3:Set the Dterm PSII to download
mode by simultaneously
applying power to the D
term PSII
and pressing the “L1” key.
Note 4:If the download is successful, it
will display the Dterm PSII
number for 2 seconds,
automatically reset, then return
to stand-by mode.
If the download failed, an error
tone will sound and the D
term
PSII displays “Download
Failed”. Download must be
performed again. If this
procedure continues to fail,
contact the Service Center.
Note 5:The following will be displayed
on the MAT.
STATUS 
DISPLAY
Loading succeeded  OK
PS is busy  WAIT BUSY NOW
PS is out of area  WD ERROR
Lack of PS data  DATA ERROR
(1)
(2)YY=20 
X-XXXX: PS Station No.
1: To be executed
See “D
term PS User Manual”.
CM1D
END
B 
						

							CHAPTER 4 ND-46248 (E)
Pag e 12 4
Revision 2.0
SYSTEM DATA PROGRAMMING
3.4 Virtual Line/Trunk Data Assignment
For Integrated Type/Adjunct Type2 (CCIS)
DESCRIPTION DATA
Assign a Virtual Line/Trunk Circuit No. to the 
required LEN.
Note 1:Be sure to assign the Station No.
to the Level 1 and Level 3.
Be sure to assign the Trunk No.
to the Level 0 and Level 2.
Note 2:The Virtual Line/Trunk Circuit
No. must be assigned from the
last LEN No. 0511.(1)
(2)LEN: (0511-0000)
X-XXXX: Virtual Station No.
D000-D255: Virtual Trunk No.
Specify type for signal as DP to each Virtual 
Station No.
(1)
(2)CM12 YY=00 (DP or DTMF)
X-XXXX:  Virtual Station No. assigned 
by CM10
1: DP
Specify the Reverse Signal (answer/release 
signal) to be sent to station, to each Virtual 
Station No.
(1)
(2)CM13 YY=18 (Reverse Signal)
X-XXXX:  Virtual Station No. assigned 
by CM10
0: To be sent
Assign the data for the Virtual Line/Trunk to 
the Virtual Trunk No. assigned by CM10.
(1)
(2)YY=00 
Virtual Trunk No. (000–255) 
Trunk Route No. (00–63)


(1)
(2)


(1)
(2)YY=02 (Terminating System in Day 
Mode)
YY=03 (Terminating System in Night 
Mode)
Virtual Trunk No. (000-255)
04 (Direct-In Termination
YY=04 (Destination in Day Mode) 
YY=05 (Destination in Night Mode)
Virtual Trunk No. (000-255)
X-XXXX: PS Station No. assigned by 
CM1C.
START
CM10
CM12
CM30
A
CM13 
						

							ND-46248 (E) CHAPTER 4
Pag e 12 5
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the data for the Virtual Line/Trunk to 
the Trunk Route No. assigned by CM30 
YY=00.
(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)YY=00 (Kind of Route)
Trunk Route No. (00-63)
00: DDD
YY=01 (Type of Signal)
Trunk Route No. (00-63)
4: DTMF
YY=04 (Answer Signal Condition)
Trunk Route No. (00-63)
1: Answer Signal by Polarity Reversal
YY=05 (Release Signal Condition)
Trunk Route No. (00-63)
1 : Release Signal from C.O.
YY=09 (Incoming Connection Signaling)
Trunk Route No. (00-63)
15 : Ring Down (Loop Start)
YY=20 (Sender Start Condition)
Trunk Route No. (00-63)
15 : Timing Start
YY=98 (Designated Seizure of trunks)
Trunk Route No. (00-63)
0: Allowed
Specify the CDT card Terminating Imped-
ance.
(1)
(2)YY=100
Trunk Route No. (00-63)
0 : 600 
Ω/complex BNW for Integrated 
Type and Adjunct Type (2)
2 : 600 
Ω/600 
Ω for Adjunct Type (1)
(LC-COT)CM35
A
B







 
						

							CHAPTER 4 ND-46248 (E)
Pag e 12 6
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify a path between the Virtual Line and 
Trunk assigned by CM10.
Note:Combination must be as follows:
 Level 0 Trunk No. and Level 1
Station No.
 Level 2 Trunk No. and Level 3
Station No.
(1)
(2)YY=00
Block No. (000-169)
DXXX (Virtual Trunk No. 000-255)
+ + X-XXXX (Virtual Station No.)
Assign the Virtual Trunk to be seized on each 
PS station basis.
(1)
(2)YY=16
X-XXXX: PS Station No.
D000-D255: Virtual Trunk No.
CM5A
CM12
END
B
, 
						

							ND-46248 (E) CHAPTER 4
Pag e 12 7
Revision 2.0
SYSTEM DATA PROGRAMMING
The example of the data setting for the Virtual Line/Trunk is as follows:
LEN No. LEVEL CM10CM12 CM13 CM30
YY=00 YY=18 YY=00 YY=02 YY=03 YY=04 YY=05
0511LEVEL 
3201 1 0
0510LEVEL 
2D001ROUTE 
No.04 04PS 
Station 
No.
ex.)A201PS 
Station 
No.
ex.)A201
0509LEVEL 
1200 1 0
0508LEVEL 
0D000ROUTE
No.04 04PS 
Station 
No.
ex.)A200PS 
Station 
No.
ex.)A200
LEN No. LEVELCM35
YY=00 YY=01 YY=04 YY=05 YY=09 YY=20 YY=98
0511LEVEL 
3
0510LEVEL 
200 4 1 1 15 15 0
0509LEVEL 
1
0508LEVEL 
000 4 1 1 15 15 0
1st Data.CM5A
1st DataCM12
YY=00 YY=16
BLOCK No.000 D000, 200 PS Station No. A200 D000
BLOCK No. 001 D001, 201 PS Station No. A201 D001
BLOCK No. 002 D002, 202 PS Station No. A202 D002
BLOCK No. 003 D003, 203 PS Station No. A203 D003
BLOCK No. 169 DXXX, XXXX PS Station No. XXXX DXXX 
						

							CHAPTER 4 ND-46248 (E)
Pag e 12 8
Revision 2.0
SYSTEM DATA PROGRAMMING
3.5 Trunk Data Assignment
For Adjunct Type1
DESCRIPTION DATA
Assign a Trunk No. to the required LEN. (1)
(2)LEN (0000-0511)
Trunk No. (D000-D255)
Assign the Trunk Route No. to the Trunk No.
(1)
(2)YY=00 (DP or DTMF)
Trunk No. (000-255)
Trunk Route No. (00-63)
Assign the data for terminating system.

(1)
(2)YY=02 (Day Mode)
YY=03 (Night Mode)
Trunk No. (000-255)
04: DIT
Assign the PS Station No. to be terminated by 
DIT.

(1)
(2)YY=04 (Day Mode) 
YY=05 (Night Mode)
Trunk No. (000-255)
X-XXXX: PS Station No.
Assign the kind of trunk to the trunk route.
(1)
(2)YY=00
Trunk Route No. (00-63)
00: C.O. Trunk
Specify the Dialing Signal Type to the trunk 
route.
(1)
(2)YY=01
Trunk Route No. (00-63)
2 : Call Origination–DP
Call Termination–DP
4 : Call Origination–DTMF
Call Termination–DTMF
7 : Call Origination–DP/DTMF
Call Termination–DTMF
Assign the Call Direction to the trunk route.
(1)
(2)YY=02
Trunk Route No. (00-63)
3 : Bothway Trunk
START
CM10
CM30
A
CM35