NEC Neax 2000 Ivs Wcs System Manual

							ND-46248 (E) CHAPTER 4
Pag e 13 9
Revision 2.0
SYSTEM DATA PROGRAMMING
3.6.4 Group Call-Automatic Conference (6/10 Party) Data Assignment
To provide the Group Call-Automatic Conferrence (6/10 Party):
DESCRIPTION DATA
Assign a Conference Trunk Card Number to 
the required LEN.(1)
(2)LEN (0000-0511)
ED00-ED03: Conference Trunk Card No.
Assign the stations which belongs to each pag-
ing group, and their number within the group. 
A maximum of 9 stations can be paged simul-
taneously except the conference leader.
Note 1:Single line telephones, Multline
Terminals and PS can be as-
signed as the station within the
group.
A virtual-line cannot be as-
signed.
Note 2:A station can belong to multiple
groups.
(1)
(2)YY=00-07: Simultaneous Paging Group 0-
7
00-15: Serial No. within the Group
X-XXXX: Station No.
Assign a Service Restriction Class to each sta-
tion.
(1)
(2)YY=02
X-XXXX: Station No.
XX
 XX
00-15 : Service Restriction 
Class A
Allow the Service Restriction Class A to page 
the group.
(1)
(2)YYY=119
00-15: Service Restriction Class A assigned 
by CM12 YY=02
0: Allowed
Assign the access code of paging groups for 
Group Call-Automatic Conference (6/10 Par-
ty).
Note:Even if an extension does not be-
long to the conference group, the
extension can page the confer-
ence group, and can re-partici-
pate in the conference if there is
an idle circuit on the Conference
Tr u n k .
(1)
(2)Y=0-3 (Tenant Group No.)
X-XX: Access Code
B00: Simultaneous Paging Group 0
B07: Simultaneous Paging Group 7
B10: Re-participation Group 0
B17: Re-participation Group 7
START
CM56
CM12
CM20
CM15
A
CM10
INITIAL
~ ~
~ ~ 
						

							CHAPTER 4 ND-46248 (E)
Pag e 14 0
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign a Group Call-Automatic Conference 
(6/10 Party) key of each paging group to the 
Multiline Terminal, if required.
Note:Even if an extension does not be-
long to the conference group, the
extension can page the confer-
ence group, and can re-partici-
pate in the conference if there is
an idle circuit on the Conference
Tr u n k .
(1)
(2)Y=00
X-XXXX: Primary Extension No. +  
+key No.
F0B00: Simultaneous Paging Group 0
F0B07: Simultaneous Paging Group 7
F0B10: Re-participation Group 0
F0B17: Re-participation Group 7
Specify the duration of simultaneous paging.
(1)
(2)Y=0
95
01-99: 4-396 sec. in 4 sec. increments
If no data is set, the default setting is 32-36 
seconds.
CM41
A
END
CM90,
~ ~
~ ~ 
						

							ND-46248 (E) CHAPTER 4
Pag e 14 1
Revision 2.0
SYSTEM DATA PROGRAMMING
3.6.5 Group Call-2 Way Calling
To provide the Group Call-2 Way Calling:
DESCRIPTION DATA
Assign the stations which belongs to each pag-
ing group, and their number within the group. 
A maximum of 9 stations can be paged simul-
taneously except the conference leader.
Note 1:Single line telephones, Multline
Terminals and PS can be as-
signed as the station within the
group.
A virtual-line cannot be as-
signed.
Note 2:A station can belong to multiple
groups.
(1)
(2)YY=00-07: Simultaneous Paging Group 0-
7
00-15: Serial No. within the Group
X-XXXX: Station No.
Assign a Service Restriction Class to each sta-
tion.
(1)
(2)YY=02
X-XXXX: Station No.
XX
 XX
00-15 : Service Restriction 
Class A
Allow the Service Restriction Class A to page 
the group.
(1)
(2)YYY=119
00-15: Service Restriction Class A assigned 
by CM12 YY=02
0: Allowed
Assign the access code of paging groups for 
Group Call-2 Way Calling.
Note:Even if an extension does not be-
long to the conference group, the
extension can page the confer-
ence group.
(1)
(2)Y=0-3 (Tenant Group No.)
X-XX: Access Code
B20: Simultaneous Paging Group 0
B27: Simultaneous Paging Group 7
Assign a Group Call-2 Way Calling key of 
each paging group to the Multiline Terminal, 
if required.
Note:Even if an extension does not be-
long to the conference group, the
extension can page the confer-
ence group.
(1)
(2)Y=00
X-XXXX: Primary Extension No. +  
+ key No.
F0B20: Simultaneous Paging Group 0
F0B27: Simultaneous Paging Group 7
START
CM56
CM12
CM20
CM15
END
CM90
~ ~
,
~ ~ 
						

							CHAPTER 4 ND-46248 (E)
Pag e 14 2
Revision 2.0
SYSTEM DATA PROGRAMMING
3.6.6 Multi-Line Operation-PS
DESCRIPTION DATA
Assign a PS station number to the virtual PS 
number.(1)
(2)Virtual PS No. (0001-0255)
X-XXXX: Primary PS Station No. 
Note
X-XXXX: Sub-line PS Station No. Note
Assign the sub-line PS number to each prima-
ry PS station.
(1)
(2)YY=01
X-XXXX: Primary PS Station No. 
Note
X-XXXX: Sub-line PS Station No. Note
Assign PS-ID of the sub-line PS as “NONE”.
(1)
(2)YY=21
X-XXXX: Sub-line PS Station No. 
Note
NONE
Specify the terminal kind of the PS as “D
term 
PS II”.
This data must be set to both the primary PS 
station number and the sub-line PS station 
number.
(1)
(2)YY=15
X-XXXX: Primary PS Station No., Note
Sub-line PS Station No. Note
00: Dterm PS II
Provide the Multi-Line function to the virtual 
PS No. for the sub-line PS.
(1)
(2)YY=05
X-XXXX: Virtual PS No.
0: Provided (Sub-line station)
Assign the virtual line/trunk data for the sub 
line PS as same as the primary PS, by the de-
scribed in the Section 3.4 and 3.5.Refer to the Section 3.4 and 3.5.
Note:PS Station number is assigned by
CM 1C.
START
CM1C
CM1D
END
CM12
CM10
CM12
CM13
CM30
CM35
CM5A 
						

							ND-46248 (E) CHAPTER 4
Pag e 14 3
Revision 2.0
SYSTEM DATA PROGRAMMING
To assign the PS station to the line key on the Dterm, assign the following data.
DESCRIPTION DATA
Assign a virtual PS station number to the key 
number of the Dterm.
A virtual PS number of PS sub-line can be as-
signed to the key on the D
term.
(1)
(2)YY=00
Primary Extension No. +   + Key No.
X-XXXX: Virtual PS Station No.
CM90
END START, 
						

							CHAPTER 4 ND-46248 (E)
Page 143-1 Addendum-001
Revision 2.1 MARCH, 1999
SYSTEM DATA PROGRAMMING
3.6.7 Number Sharing
DESCRIPTION DATA
Specify the combination of the main station 
and the sub station, also the contrary 
combination, as follows.
1st data: Main station (D
term My Line)
2nd data: Sub station (PS)
1st data: Sub station (PS)
2nd data: Main station (D
term My Line)
Note:As the main station number, Dterm
My Line number must be
assigned.
As the sub station number,
following number must be
assigned.
• Integrated type/Adjunct type
(CCIS):
Virtual PS number assigned
by CM10.
•Adjunct type (LC-COT):
PS station number assigned
by CM30 YY=04.
(1)
(2)YY=16 (Assignment of the main station 
and the sub station)
X-XXXX: Main station (D
term My Line)
No./sub station (PS) No.
X-XXXX: Sub station (PS) No./main
station (D
term My Line) No.
Assign the Class of Service to required sta-
tions.
Note:For the Trunk Restriction Class
(CM12 YY=01) and the Tenant
Number (CM12 YY=04), the
same data must be assigned to the
sub station and the main station.
(1)
(2)YY=02 
X-XXXX (Station No.)
XX
XX
To the sub station (PS), specify the number 
which is informed to calling/called party, 
SMDR and MCI as the main station number.
(1)
(2)YYY=127
Service Restriction Class A of sub station 
(00-15)
0: Main station number is informed
Provide the capability of setting/cancelling the 
Number Sharing from the sub station.
(1)
(2)YYY=128
Service Restriction Class A of sub station 
(00-15)
0: To provide
START
CM12
A
CM15
Service Restriction Class A
(00-15) 
						

							ND-46248 (E) CHAPTER 4
Addendum-001 Page 143-2
MARCH, 1999 Revision 2.1
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify whether the sub station is controlled 
the same as the main station, by a Message 
Waiting lamp control signal sent from the 
MC1.
Note:This assignment is effective only
when the system is an Integrated
type.
(1)
(2)YYY=129
Service Restriction Class A of Main station 
(00-15)
0: Main station and sub station are con-
trolled.
1 : Only main station is controlled.
Provide the PS11 station(s) with Message 
Waiting Service.
Note:This assignment is only necessary
if Data 0 (Main station and Sub
station are controlled) is selected
in CM15 YYY=129 for Service
Restriction Class A of Main
station.
(1)
(2)YY=03 
X-XXXX: Virtual PS No.
0: To be provided
Provide the Number Sharing set/cancel key to 
the main station (D
term).
(1)
(2)YY=00
My Line No. + + Key No.
F0A94: Number Sharing Set/Cancel
Assign the Access Code for setting or cancel-
ling Number Sharing from the sub station 
(PS).
(1)
(2)Y=0-3 (Tenant Group Number)
X-XXX: Access Code
A92: Set Number Sharing from the sub sta-
tion
A93: Cancel Number Sharing from the sub 
station
CM15
A
CM13
END
CM90
CM20
, 
						

							CHAPTER 4 ND-46248 (E)
Page 144 Addendum-001
Revision 2.1 MARCH, 1999
SYSTEM DATA PROGRAMMING
3.6.8 Voice Mail Indication
DESCRIPTION DATA
Provide PS stations with Message Waiting 
service.
The first data should be the virtual PS number.•
(1)
(2)YY=03
X-XXXX: Virtual PS No.
0: To be providedCM13
END START 
						

							ND-46248 (E) CHAPTER 4
Pag e 14 5
Revision 2.0
SYSTEM DATA PROGRAMMING
3.7 Multi-Site Roaming Data Assignment
According to the following procedure, assign the system data for Roaming service.
Confirming Network Numbering Plan
Confirm whether the network adopts Open Numbering System or Closed Numbering System for the net-
work numbering plan.
Note:The System data stored in the memory of the DBM (AP00) card can be saved, loaded and verified from
the MAT.
To save; Memory Area No.: A, Memory Address: 00900-10870
To load or verify; File Extension: DMA
PREPARATION
Confirming Network Numbering Plan
(Open Numbering System/Closed Numbering System)
START
Numbering Plan Data Assignment
(Open Numbering System/Closed Numbering System)
Q931a Digital Trunk Assignment
(for Home PBX and Visitor PBX)
Roaming PS Data Assignment
(for Home PBX and Visitor PBX)
Home PS Data Assignment
(for Home PBX)
Visitor PS Data Assignment
(for Visitor PBX)
ENDSee this section.
See Section 3.7.1.
See Section 3.7.2.
See Section 3.7.2 ~3.7.3.
See Section 3.7.3.
See Section 3.7.4. 
						

							CHAPTER 4 ND-46248 (E)
Pag e 14 6
Revision 2.0
SYSTEM DATA PROGRAMMING
3.7.1 Network Numbering Plan Assignment
DESCRIPTION DATA
Assign an access code for LCR Group 0-3.
For Closed Numbering System, assign the sec-
ond data to A29 (LCR Group 3).
(1)
(2)Y=0-3 (Numbering Group 0-3)
X-XXXX: Access Code
A26: LCR Group 0
A27: LCR Group 1
A28: LCR Group 2
A29: LCR Group 3
Specify the number of digits and the first digit 
for station number.
(1)
(2)Y=0-3 (Numbering Group 0-3)
X: First Digit of Station No.
801: 1 digit
802: 2 digits
803: 3 digits
804: 4 digits
Assign an Area Code Development Pattern 
No. to each LCR Group. 
For Closed Numbering System, assign the first 
data to 3.
(1)
(2)YYY=A00
0-3: LCR Group 0-3 
0-7: Area Code Development Pattern 
No. 0-7 
Assign a Route Pattern No. to each area code 
for the Area Code Development Pattern No. 
assigned by CM8A YYY=A00.
(1)
(2)YYY=400-407 (Area Code Development 
Pattern No. 0-7) 
XX...XX (Area Code, Max. 8 digits) 
000-063 (Route Pattern No. 00-63) 
Assign an area code including LCR access 
code assigned by CM20-A29.
(1)
(2)YYY=400-407 (Area Code Development 
Pattern No. 0-7) 
X-XXXXX (Area Code, 1-5 digits) 
800 (Intra-Office Termination)
801 (1-digit intra-office station) 
802 (2-digit intra-office station) 
803 (3-digit intra-office station)
804 (4-digit intra-office station) 
805 (5-digit intra-office station)
START
CM20
CM8A
A