NEC Neax 2000 Ivs Wcs System Manual

							ND-46248 (E) CHAPTER 4
Pag e 12 9
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the Application of answer signal from 
the distant office for outgoing connection to 
the trunk route.
(1)
(2)YY=04
Trunk Route No. (00-63)
1 : Battery Reversal
7 : Answer signal does not arrive from 
C.O. Line (Answer timing shall be set by 
CM41Y=0 Function No. 03)
Specify the Application of release signal from 
the distant office for an outgoing connection 
of an incoming connection to the trunk route.
(1)
(2)YY=05
Trunk Route No. (00-63)
0 : Release signal does not arrive
1 : Release signal arrives
Note:In case of Adjunct Type1 (LC-
COT), using a line card over
the Main PBX is recommend-
ed to provide the release sig-
nal (i.e., momentarily, an open
circuit).
Assign the Sending of the dial pulse on an out-
going call to the trunk route.
(1)
(2)YY=08
Trunk Route No. (00-63)
3 : Dial pulses are sent out
Assign the Incoming Connection Signaling to 
the trunk route.
(1)
(2)YY=09
Trunk Route No. (00-63)
15 : Ring Down (Loop Start C.O.)
Assign the Sending of Hook Flash to outside 
to the trunk route.
(1)
(2)YY=16
Trunk Route No. (00-63)
1 : Sending
Assign the Sender Start Condition to the trunk 
route.
(1)
(2)YY=20
Trunk Route No. (00-63)
15 : Timing Start
CM35
B
A











 
						

							CHAPTER 4 ND-46248 (E)
Pag e 13 0
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the Sender Prepause Timing to the 
trunk route.
(1)
(2)YY=21
Trunk Route No. (00-63)
00: 0 sec. 08: 6.0 sec.
01: 0.5 sec. 09: 7.0 sec.
02: 1.0 sec. 10: 8.0 sec.
03: 1.5 sec. 11: 9.0 sec.
04: 2.0 sec. 12: 10.0 sec.
05: 2.5 sec. 13: 11.0 sec.
06: 4.0 sec. 14: 12.0 sec.
07: 5.0 sec. 15 : 3.0 sec.
Note:To reduce the connecting time,
shorten the prepause timing
(i.e., second data=03 (1.5
sec.))
Specify the DP Inter-Digital Pause to the trunk 
route.
(1)
(2)YY=23
Trunk Route No. (00-63)
0: 300 ms. 4: 700 ms.
1: 400 ms. 5: 900 ms.
2: 500 ms. 6: 1100 ms.
3: 600 ms. 7 :  800 ms.
Specify the DTMF-Inter-Digital Pause to the 
trunk route.
(1)
(2)YY=24
Trunk Route No. (00-63)
0:  32 ms. 4: 160 ms.
1: 64 ms. 5: 192 ms.
2: 80 ms. 6: 240 ms.
3: 96 ms. 7 :  128 ms.
Note:To reduce the connecting time,
it is recommended to shorten
the DTMF inter-digital Pause
timing (YY=24), i.e., second
data=2 (80ms). YY=26, i.e.,
second data= 0 (64ms)
Assign the DP Make Ratio to the trunk route.
(1)
(2)YY=25
Trunk Route No. (00-63)
0 : 39% Make Ratio
1 : 33% Make Ratio
C
CM35
B







 
						

							ND-46248 (E) CHAPTER 4
Pag e 13 1
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the DTMF Signal Width to the trunk 
route.
(1)
(2)YY=26
Trunk Route No. (00-63)
0 : 64 ms.
1 : 128 ms.
Note:To reduce the connecting time,
it is recommended to shorten
the DTMF inter-digital Pause
timing (YY=24), i.e., second
data=2 (80ms). YY=26, i.e.,
second data=0 (64ms)
Assign the Trunk Release by detection of re-
versal of tip and ring to the trunk route.
(1)
(2)YY=39
Trunk Route No. (00-63)
0 : Not to be released
1 : To be released
CAUTION:Check the timing on Main PBX before making any change on timing function (after
PBX).
Specify the DP Sender Release Timing to the 
trunk route.
(1)
(2)YY=45
Trunk Route No. (00-63)
0: 2 sec.
1: 4 sec.
2: 6 sec.
3: 8 sec.
4: 12 sec.
5: 14 sec.
6: 16 sec.
7: 10 sec.
Specify the DTMF Sender Release Timing to 
the trunk route.
(1)
(2)YY=46
Trunk Route No. (00-63)
0: 2 sec.
1: 4 sec.
2: 6 sec.
3: 8 sec.
4: 12 sec.
5: 14 sec.
6: 16 sec.
7: 10 sec.
Specify the designated seizure of trunks on 
each station basis.
(1)
(2)YY=98
Trunk Route No. (00-63)
0: Allowed
CM35
C
D







 
						

							CHAPTER 4 ND-46248 (E)
Pag e 13 2
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the CDT card Terminating Impedance.
(1)
(2)YY= 100
Trunk Route No. (00-63)
0 : 600 
Ω/complex BNW for Integrated 
Type and Adjunct Type(2)
2 : 600 
Ω/600 
Ω for Adjunct Type(1) 
(LC-COT)
Assign the trunk to be seized on each PS sta-
tion basis.
(1)
(2)YY=16
X-XXXX: PS Station No.
D000-D255: Trunk No.
Automatic Pause Entry Table
Designate digits requiring automatic pause.
(1)
(2)Y=0
Block Number (00-04)
Dialed digits before automatic pause 
(Exclusive of Access Code)
X: 0-9, A (*), B (#)
Provide automatic pause.
(1)
(2)Y=1
00
3 (To be provided)
Timing automatic pause.
(1)
(2)Y=2
00
2 (1.5 sec.)
CM88
END
CM12
CM35
D

 
						

							ND-46248 (E) CHAPTER 4
Pag e 13 3
Revision 2.0
SYSTEM DATA PROGRAMMING
3.6 Service Feature Data Assignment
3.6.1 Announcement Service
Refer to Appendix A for the operating procedure.
To provide the Announcement Service:
DESCRIPTION DATA
Assign a Digital Announcement Trunk Circuit 
No. to the required LEN.
Note:The Digital Announcement Trunk
Circuit No. must be assigned to
the first LEN (Level 0) and/or the
third LEN (Level 2) of each LT
slot.(1)
(2)LEN (0000-0511)
EB000-EB127: Digital Announcement 
Trunk Circuit No.
For PIM 0/1: EB000-EB031
For PIM 2/3: EB032-EB063
For PIM 4/5: EB064-EB095
For PIM 6/7: EB096-EB127
Assign a tenant No. to a PS station. (1)
(2)YY=04
X-XXXX: PS Station No.
00 : Tenant 00
1 : Tenant 01
63: Tenant 63
Specify whether PS Out of Cell/PS Power Off 
are separated from No-Answer.
Specify types of No-Answer Timer.
Note:This data is effective only when
CM08-086 is set to 0.(1)
(2)
(1)
(2)086
0: Separated
1 : Not Separated (Handled as No-An-
swer)
085
0 : No-Answer timer (CM41·Y=0-86)
1 : No-Answer timer (CM41·Y=0-01)
Specify the message reply timer for the An-
nouncement Service when a PS does not an-
swer.
(1)
(2)Y=0
01
01-30: 4-120 sec. in 4 sec. increments 
Note:This data is effective only when
CM08-085 and 086 are set to 1.If no data is set, the default setting is 32-36 
seconds.
Specify the message reply timer for the An-
nouncement Service when a PS does not an-
swer.
(1)
(2)Y=0
86
01-99: 4-396 sec. in 4 sec. increments
Note:This data is effective only when
CM08-085 and 086 are set to 0.If no data is set, the default setting is 36-40
seconds
START
CM10
CM12
CM41
CM08
A
INITIAL


~



 
						

							CHAPTER 4 ND-46248 (E)
Pag e 13 4
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the message reply timer for the An-
nouncement Service when a PS is out of cell/PS 
power is off.
Note:This data is effective only when
CM08-086 is set to 0.
(1)
(2)Y=0
85
01-99: 4-396 sec. in 4 sec. increments
If no data is set, the default setting is 8-12 sec-
onds.
Specify the duration of message for the An-
nouncement Service when a PS does not an-
swer.
(1)
(2)Y=0
75
01-99: 4-396 sec. in 4 sec. increments
If no data is set, the default setting is 116-120 
seconds.
Specify the duration of message for the An-
nouncement Service when a PS is out of cell/PS 
power is off.
(1)
(2)Y=0
84
01-99: 4-396 sec. in 4 sec. increments
Note:This data is effective only when
CM08-086 is set to 0.If no data is set, the default setting is 116-120 
seconds.
Provide the Announcement Service.
(1)
(2)Y=5
00: PS No-Answer
02: PS Out of Cell/PS Power Off
0500: To be provided
1500: Not to be provided
NONE
 : Not to be provided
Assign the function for each Digital Announce-
ment Trunk.
(1)
(2)YY=00
000-127: Digital Announcement Trunk 
assigned by CM10 
(EB000-EB127)
1300-1363: PS No Answer Message Group 
No. 00-63
1500-1563: PS Power Off/Out of Cell 
Message Group No. 00-63
NONE : None
Assign the message group for each tenant when 
a PS does not answer.
(1)
(2)YY=10
00-63: Tenant No.
00-63: Message Group No.
NONE : None
Assign the message group for each tenant when 
a PS is out off cell/PS power is off.
(1)
(2)YY=12
00-63: Tenant No.
00-63: Message Group No.
NONE : None
CM41
CM48
A
END
CM49







 
						

							ND-46248 (E) CHAPTER 4
Pag e 13 5
Revision 2.0
SYSTEM DATA PROGRAMMING
To record/replay/delete a message from a station:
There are two methods to record/replay/delete a message from a PS or a station, as mentioned below.
1. To record/replay/delete a message from a station or a PS by dialling an access code assigned by CM20, do
the following programming.
This method is available for only the Integrated Type.
DESCRIPTION DATA
Assign the Class of Service for the 
Announcement Service to a certain PS/station.

(1)
(2)CM12 YY=02
(Service Restriction Class A)
CM15 YY=33 
(Digital Announcement Trunk Access: 
Record/Replay/Delete)
Service Restriction Class A (00-15)
0/1 
u: Restricted/Allowed
Assign the access codes to record, replay, and 
delete the message.
(1)
(2)Y=0-3 (Numbering Plan Group 0-3)
X-XXX: Access Code
A00: Record
A01: Replay
A02: Delete
Refer to Appendix A for the operating procedure.
CM12
END
START
CM15
CM20 
						

							CHAPTER 4 ND-46248 (E)
Page 136 Addendum-001
Revision 2.1 MARCH, 1999
SYSTEM DATA PROGRAMMING
2. To record/replay/delete a message from a PS by dialing “1”, “2”, “3”, do the following programming.
This method is available for both the Integrated Type and the Adjunct Type.
DESCRIPTION DATA
Assign the Class of Service for the Announce-
ment Service to a certain PS/station.
Note:By this method, while a PS
specified to “Allowed” to record/
replay/delete a message by CM15
YYY=110, the PS cannot
originate a call. Specify to
“Restricted” by CM15 YYY=110
again after a message is
completed to record/replay/
delete.

(1)
(2)CM12 YY=02
(Service Restriction Class A)
CM15 YYY=110 
(Digital Announcement Trunk Access: 
Record/Replay/Delete)
Service Restriction Class A (00-15)
0/1 : Allowed/Restricted
Refer to Appendix A for the operating procedure.
CM12
END START
CM15

 
						

							ND-46248 (E) CHAPTER 4
Addendum-001 Page 137
MARCH, 1999 Revision 2.1
SYSTEM DATA PROGRAMMING
3.6.2 Call Forwarding-Not Available
DESCRIPTION DATA
Assign the destination VMS station for Call 
Forwarding-Not Available.•
(1)
(2)YY=20
00-63: Tenant No. of Virtual PS
X-XXXX: VMS Station No.
Assign the access code to set/cancel Call For-
warding when the incoming call is not avail-
able, and set the access code to replay the 
message.
Provide the PSII station(s) with Message 
Waiting Service.
Note:This assignment is only necessary
if data 0 (Main Station and Sub
Station are controlled) is selected
in CM15 YYY=129 for Service
Restriction Class A of Main sta-
tion.
(1)
(2)

(1)
(2)Y=0-3 (Numbering Plan Group 0-3)
X-XXX: Access Code
A89: Call Forwarding-Not Available Set
A90: Call Forwarding-Not Available 
Cancel
A91: Call Forwarding-Not Available 
Replay
YY=03
X-XXXX: Virtual PS No.
0: To be provided
Specify whether confirmation of message 
existence by Special Dial Tone is available or 
not.
If the second data is set to 0, the Special Dial 
Tone is sent when a message exists.
(1)
(2)Y=2
12 (Confirmation by Dial Tone)
0:Available
1 : Not available
Specify that PS Out of Cell/PS Power Off is 
separated from No-Answer.
Set the Class of Service for the Call Forward-
ing-Not Available to each PS station.(1)
(2)


(1)
(2)086 : PS Out of Cell/PS Power Off
0 : Separated
CM12 YY=02 (Service Restriction Class 
A)
CM15 YYY=115 (Call Forwarding-Not 
Av a i l a b l e )
Service Restriction Class A for the Virtual 
PS Station (00-15)
0 : Restricted
1 : Allowed
CM12
END START
CM15
CM20
CM48
CM51
CM13
CM08 
						

							CHAPTER 4 ND-46248 (E)
Pag e 13 8
Revision 2.0
SYSTEM DATA PROGRAMMING
3.6.3 Calling Name Display-PS
Refer to the following manuals for the name display feature programming.
Feature Programming Manual; Alphanumeric Display, Caller ID Class
CCIS System Manual; Calling Name Display-CCIS
PMS System Manual; Guest Name Display
DESCRIPTION DATA
Specify the terminal kind of the PS as “Dterm 
PS II”.
(1)
(2)YY=15
X-XXXX: PS Station No. (Assigned by 
CM1C)
00: D
term PS II
Specify the kind of the ZT as “D
term PSII
type ZT”.
(1)
(2)YY=19
X-XXXX: ZT No.
00: D
term PS II Type ZT
Assign a Service Restriction Class to each sta-
tion.
Note 1

(1)
(2)YY=02
X-XXXX: PS Station No. (Assigned by 
CMIC)
XX XX
00-15  : Service Restriction 
Class A
Provide Calling Name Display to PS
(1)
(2)YYY=123
00-15 : Service Restriction Class A as-
signed by CM 12 YY=02
0 : Available
1   : Not Available
Note 1:The previous PS Dterm does not
provide the Calling Name Dis-
play feature; therefore, this data
shuld be set to “1” Not Avail-
able. Set data to “0” Available if
providing service for the D
term
PS II.
START
CM1D
CMAD
END
CM12
CM15