NEC Neax 2000 Ivs Wcs System Manual

							ND-46248 (E) CHAPTER 3
Pag e 10 1
Revision 2.0
INSTALLATION
Figure 3-53    Switch Settings on DBM Card
RUN
SW1
WE
L3
SW1
ON
OFF
SET THE KNOB TO MATCH THE
AP NO. (04-15) TO BE SET BY
CM05SENSE
:POSITION TO BE SET 1 2 3 4
RS3
ATTENTIONContents
Static Sensitive
Handling
Precautions Required
MB
UP
L2
L1
L0
RS1
RS0 RS2
SW0
MB
SENSE
SW0
ON12345678
: POSITION TO BE SET.
J16
J16
: POSITION TO BE SET RIGHT : MEMORY BACKUP ON 
						

							CHAPTER 3 ND-46248 (E)
Pag e 10 2
Revision 2.0
INSTALLATION
STEP 2: Mount the DTI, DCH and DBM card in AP slots on PIM0-PIM7 as follows.
2000 IVS1000 IVS
DTI card: AP0-AP6 DTI card: AP0-AP4
DCH card: AP0-AP8 DCH card: AP0-AP4
DBM card: AP0-AP8 DBM card: AP0-AP4
Small Platform System
DTI card: AP0-AP3
DCH card: AP0-AP5
DBM card: AP0-AP5
After mounting the card, set the SENS switch to match an unequipped AP number in CM05. And set
the MB switch to down position to put the card in service. For details on mounting locations, refer to
the Circuit Card Manual. 
						

							ND-46248 (E) CHAPTER 3Pag e 10 3
Revision 2.0
INSTALLATION
5.3 Selection of PLO in MP Card
STEP  1:  On  the  M P (PN-C P00 /C P00-B /CP03)  c ard,  set  t he  sw itch es as  s h ow n  in  Fig ure  3-5 4.
Figure 3-54    Switch Settings on MP Card (1 of 3)
RUN
SW2
ON
OFF
0: ON LINE MODE
: POSITION TO BE SET
1 
2 
3 
4
JP0
SW3
CLKIN JP0
RS
ON: KF MODE 
OFF: PF/MF MODE (STANDARD SETTING FOR U.S.A.)
SW1 
SW2
ATTENTIONContents 
Static Sensitive
Handling 
Precautions Required
PN-CP00
 WHEN USING THE INTERNAL PLO  WHEN USING THE PLO CARD
SW2-2 SW2-3 SW2-2 SW2-3 OFF OFF : 1.5 MHz CLOCK OFF ONON OFF : 192 kHz CLOCK
OFF ON : 2 MHz CLOCK ON ON : NOT USED WHEN NOT USING THE INTERNAL PLO 
AND THE PLO CARD
SW2-2 SW2-3 OFF OFF
RIGHT: NORMAL  OPERATION
: POSITION TO BE SET SW3 
						

							CHAPTER 3 ND-46248 (E)
Pag e 10 4
Revision 2.0
INSTALLATION
Figure 3-54  Switch Settings on MP Card (2 of 3)
SW3
RUN
SW1
SW2
CLKIN
JP0
0: ON LINE MODE
JP0
:  POSITION TO BE SET
  PN-CP00-B
 WHEN USING THE INTERNAL PLO WHEN USING THE PLO CARD
SW2-2SW2-3 SW2-2SW2-3
OFF OFF : 1.5 MHz CLOCK OFF ON
ON OFF : 192 kHz CLOCK
OFF ON : 2 MHz CLOCK
ON ON : NOT USED
WHEN THE INTERNAL PLO AND THE
PLO CARD ARE NOT USED
SW2-2 SW2-3
OFF OFF
SW2OFF
ON 8
 
7 
6 
5 
4 
3 
2 
1
: POSITION TO 
  BE SET
ON: KF MODE
OFF: PF/MF MODE (STANDARD SETTING
FOR U.S.A.)
UP: NORMAL  OPERATION
SW3ATTENTIONContents
Static Sensitive
Handling
Precautions Required 
						

							ND-46248 (E) CHAPTER 3
Pag e 10 5
Revision 2.0
INSTALLATION
Figure 3-54  Switch Settings on MP Card (3 of 3)
STEP 2: Mount the MP card on the MP slot of PIM0.
SW2SW2
OFFON
4 
3 
2 
1 
 
SW3: POSITION TO 
  BE SET
:  POSITION TO BE SET
 0: ON LINE MODE
ON: KF MODE
OFF:  PF/MF MODE (STANDARD 
SETTING FOR U.S.A.) 
 WHEN USING THE INTERNAL PLO
SW2-2 SW2-3
OFF OFF : 1.5 MHz CLOCK
ON OFF : 192 kHz CLOCK
OFF ON : 2 MHz CLOCK
ON ON : NOT USED
 WHEN USING THE PLO CARD
SW2-2 SW2-3
OFF ON
WHEN NOT USING THE INTERNAL PLO AND THE
PLO CARD
SW2-2 SW2-3
OFF OFF
ON : USING RS 1 PORT FOR BUILT-IN MODEM
OFF : USING RS 1 PORT FOR RS-232C
JP0
JP1
VR
JP0
UP: NORMAL OPERATION
JP1
UP:  USING INTERNAL HOLD TONE
DOWN:  USING EXTERNAL HOLD TONE SOURCE
SW3
VR
20
0
 0
  PN-CP03
VARIABLE RESISTER 
FOR EXTERNAL HOLD 
TONE SOURCE
(0-20KΩ
 - CLOCKWISE)
ATTENTIONContents
Static Sensitive
Handling
Precautions Required 
						

							CHAPTER 3 ND-46248 (E) 
Pag e 10 6
Revision 2.0
INSTALLATION5.4 Mounting PLO Card
STEP  1:  On  the  PLO (PN -CK00)  ca rd,  se t t h e sw it c hes  as  sh ow n  in  Figu re 3 -55 .
Figure 3-55    Switch Settings on PLO Card
STEP 2: On the MP card, set the SW2-2 to OFF and SW2-3 to ON. 
STEP 3: Mount the PLO card in an AP slot on PIM0.
2000 IVS: AP0-AP8
 Small Platform System: AP0-AP5
 1000 IVS: AP0-AP4
After mounting the card, set the MB switch to down position to put the card in service.
MB
SW
SYNCPLO0 
PLO1
OFF
ON
8  
7  
6  
5 
4 
3 
2 
1
SW0 MB
: POSITION TO  
  BE SET
UP
ALM
DRFT
ATTENTIONContents 
Static Sensitive
Handling 
Precautions Required 
						

							ND-46248 (E) CHAPTER 3Pag e 10 7
Revision 2.0
INSTALLATION
5.5 Cable Connection via MDF for DTI
Co nne ct  the  ca b le  to a  CSU via  t h e MDF as  sh ow n  in  Figu re 3 -56 .
F igu re  3-57  sh ow s the  L T C  con nec tor  co rr e sp onds  with  the AP  s lot s, a n d DTI  pin  a ss ignment  f o r  ea ch AP
s lo t, and  F igu re 3 -58  sh ow s an  e x ample  o f t h e ca ble  c onn ect ion wh en the  DTI  ca rd is  mo unt ed in  the AP0
slot of PIM0 on the NEAX2000 IVS.
Figure 3-56    Cable Connection via MDF
CSU
MDF
TWISTED-PAIR 
CABLE
BWB
PBX 
(PIM0 - PIM7)
MAX. 200 m (655 ft.)
LTC1/LTC2 CONNECTOR 
(SEE FIGURES 3-57 AND 3-58.)
DTI
Note:The CSU must be installed to interface with the network, and must be installed on the premises 
where the PBX is. 
						

							CHAPTER 3 ND-46248 (E)
Pag e 10 8
Revision 2.0
INSTALLATION
Figure 3-57    Location of AP Slots and LTC Connectors for DTI (1 of 3)
50 25 50 25
49 24
LT11/AP149 24
48 23 48 23
47 TB 22 TA 47 22
46 RB 21 RA 46 21
45 20
LT10/AP045 20
AP6 44 19 44 19
43 TB 18 TA 43 TB 18 TA
42 RB 17 RA 42 RB 17 RA
41 16
LT0941 16
LT15/AP5 40 15 40 15
39 14 39 TB 14 TA
38 13 38 RB 13 RA
37 12
LT0837 12
LT14/AP4 36 11 36 11
35 10 35 TB 10 TA
34 09 34 RB 09 RA
33 08
LT0733 08
LT13/AP3 32 07 32 07
31 06 31 TB 06 TA
30 05 30 RB 05 RA
29 04
LT0629 04
LT12/AP2 28 03 28 03
27 02 27 TB 02 TA
26 01 26 RB 01 RA
LT15/AP5FP/AP6MP/FP/AP7BUS/AP8
LT14/AP4
LT13/AP3
LT12/AP2
LT11/AP1
LT00 LT01 LT02 LT09
LT04 LT08
LT07
LT03 LT06
LT05 LT10/AP0
LTC0 LTC2LTC1 PIM
LTC1 LTC2   NEAX2000 IVS 
						

							ND-46248 (E) CHAPTER 3
Pag e 10 9
Revision 2.0
INSTALLATION
Figure 3-57  Location of AP Slots and LTC Connectors for DTI (2 of 3)
AP5MP
LT10/AP4
LT09/AP3
LT08/AP2
LT07/AP1
LT00 LT01 LT02 LT04
LT03 LT06/AP0
LTC0 LTC2LTC1 PIM
50 25
49 24
LT09/AP3 48 23
47 TB 22 TA
46 RB 21 RA
45 20
LT08/AP2 44 19
43 TB 18 TA
42 RB 17 RA
41 16
LT07/AP1 40 15
39 14
38 13
37 12
36 11
35 TB 10 TA
34 RB 09 RA
33 08
LT06/AP0 32 07
31 06
30 05
29 04
28 03
27 TB 02 TA
26 RB 01 RA
LTC2
Note:When mounting the Line/Trunk circuit card with 6 or 8 circuits into the LT08 slot, the LT09 slot
cannot be used.
  Small Platform System 
						

							CHAPTER 3 ND-46248 (E)
Pag e 11 0
Revision 2.0
INSTALLATION
Figure 3-57  Location of AP Slots and LTC Connectors for DTI (3 of 3)
MP
LT08/AP4
LT07/AP3
LT06/AP2
LT05/AP1
LT00 LT01 LT02
LT03 LT04/AP0
LTC0LTC1
50 25
49 24
LT08/AP4 48 23
47 22
46 21
45 20
44 19
43 TB 18 TA
42 RB 17 RA
41 16
LT06/LT07/AP3 40 15
39 TB 14 TA
38 RB 13 RA
37 12
LT06/AP2 36 11
35 TB 10 TA
34 RB 09 RA
33 08
LT04/LT05/AP1 32 07
31 TB 06 TA
30 RB 05 RA
29 04
LT04/AP0 28 03
27 TB 02 TA
26 RB 01 RA
LTC1   NEAX1000 IVS
PIM
Note: When mounting the Line/Trunk circuit
card with 6 or 8 circuits into the LT04
slot or LT06 slot, the LT05 slot or LT07
slot cannot be used.