NEC Neax 2000 Ivs Wcs System Manual

							ND-46248 (E) CHAPTER 4
Pag e 14 7
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the order of LCR selection for the 
Route Pattern No. assigned by YYY=400-407.
(1)
(2)YYY=000-063
(Route Pattern No. 00-63) 
1-4: Order of LCR Selection 
1: 1st
2: 2nd
3: 3rd
4: 4th
XXX
 XX 
*a: 000-255 (LCR Pattern No. 000-255)
*b: 00-63 (Trunk Route No. 00-63) 
To delete the designated digit of an area code:
(1)
(2)YYY=500-755
153 (Designation of digit to be deleted)
00: No digits deleted 
01: First digit deleted
10: First 10 digits deleted
CCC: No digits deleted
Assign the digits to be added to the digits sent 
to the distant office.
For Closed Numbering System, this assign-
ment is not required.
(1)
(2)

(1)
(2)YYY=500-755
100 (Designation of digit Addition Pattern-
No.) 
00-49 (Digit Addition Pattern No. 00-49) 
CCC: No digits added 
YYY=900-949 (Digit Addition Pattern No. 
00-49) 
0 
X-X...X [Digits to be added (Max. 32 dig-
its)] 
X=0-9, A (*), B (#), C (Fixed Pause)
A
CM8A
B*b *a
|| 
						

							CHAPTER 4 ND-46248 (E)
Pag e 14 8
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the maximum number of digits to be 
dialed by the calling party.
The maximum number of digits including the 
area codes should be assigned to each area 
code. 
(1)
(2)Y=0-7 (Area Code Development Pattern No. 
0-7 assigned by CM8A, YYY=A00)
X-X...X (Area Code dialed, Max. 8 digits) 
01 : 1 digit 
24 : 24 digits 
79 : 79 digits 
B
CM85
END
||
|| 
						

							ND-46248 (E) CHAPTER 4
Addendum-001 Page 149
MARCH, 1999 Revision 2.1
SYSTEM DATA PROGRAMMING
3.7.2 Q931a Digital Trunk Assignment
1. DTI Assignment
DESCRIPTION DATA
Assign an AP number to the DTI card.
The AP number assigned must coincide with 
the value set by the SENS switch on the DTI 
card.(1)
(2)AP No. (04-15)
09: DTI card
Assign the trunk number to each channel 
number on the DTI card.
Note:The system allocates time slots to
consecutive channels from
lowest to highest channel
number assigned. To minimize
the number of time slots
allocated, assign trunk numbers
to the consecutive channels on
each card. Never skip channels
in CM07.•
(1)
(2)YY=01
XX
 XX
*a *b
*a: AP No. assigned by CM05
*b: Channel No. of DTI 00-23
For 24-DTI
00-22: B channel
23: D channel
For 30-DTI
01-15, 17-30: B channel
16: D channel
Trunk No. (D000-D255)
Trunk number already assigned by CM10 
cannot be used.
Assign the necessary functions to the 24-DTI 
card.
After entering the data, set the MB switch on 
the DTI card to UP, and then to DOWN, for 
DTI intialization.
Note 1:These commands are only
applicable for the 24-DTI card.
Note 2:The following table shows the
relationship between CMAA
YY=01 and CMAA YY=02.
[ ] : Indicates 2nd data.
(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)YY=00 (Data Mode)
Slot No. (04-15) assigned by CM05
0: Based on AT&T Spec.
YY=01 (Frame Configuration)
Slot No. (04-15) assigned by CM05
0 : 12-Multiframe
1 : 24-Multiframe
YY=02 (Zero Code Suppression)
Slot No. (04-15) assigned by CM05
0:Available
1 : Not Available
YY=03
Slot No. (04-15) assigned by CM05
7 : Channel Associated Interoffice
Signaling
CM05 START
CM07
A
CMAA
INITIAL
INITIAL
CMAA YY=01 
(FRAME CON-
FIGURATION)CMAA YY=02
(ZERO CODE
SUPPRESSION)SIGNALING
24-multiframe [1]
B8ZS
12-multiframe [0]Not Available [1] Transparent
Available [0] B7 
						

							CHAPTER 4 ND-46248 (E)
Pag e 15 0
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign a Trunk Route to each trunk number 
used for voice channel (B channel), and also to 
signaling channel (D channel). Make a sepa-
rate route for B channels and D channels.
Note:DTI route must be separated
from analog trunk 
routes

(1)
(2)YY=00
B Channel, D channel Trunk No. (000-255) 
assigned by CM07 YY=01
Trunk Route No. (00-63)
Assign the terminating system to each incom-
ing trunk used for voice channel, as “dial-in”.
(1)
(2)YY=02 (Day Mode)
YY=03 (Night Mode)
B Channel Trunk No. (000-255) assigned 
by CM07 YY=01
21: Dial-in
Assign the CIC (Circuit Identification Code) 
to each voice channel trunk.
(1)
(2)YY=07
B Channel Trunk No. (000-255)
000-022: CIC 000-CIC 022CM30
A
B 
						

							ND-46248 (E) CHAPTER 4
Pag e 15 1
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign trunk route data to each channel trunk 
route number assigned by CM30 YY=00.
(1)
(2)YY=00 (Kind of Trunk Route)
B Channel, D Channel Route No. (00-63)
04: Tie Line

(1)
(2)YY=01 (Dialing Signal Type)
B Channel Route No. (00-63)
7 : Call Termination; DP/DTMF
Call Origination; DTMF

(1)
(2)YY=04 (Answer Signal from Distant Of-
fice)
B Channel Route No. (00-63)
2 : Answer signal arrives.
7 : Answer signal does not arrive.

(1)
(2)YY=05 (Release Signal from Distant Of-
fice)
B Channel Route No. (00-63)
0 : Release signal does not arrive.
1 : Release signal arrives.

(1)
(2)YY=09 (Incoming Connection Signaling)
B Channel Route No. (00-63)
08: Q931aCM35
B
C 
						

							CHAPTER 4 ND-46248 (E)
Pag e 15 2
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
T/R: Transmitter PAD/Receiver PAD
+: Gain
–: Loss
(1)
(2)YY=19
B Channel Route No. (00-63)
0:
1: Programmable PAD 
2: (See CM42)
3:
4:
5: Fixed PAD
6: (See left table)
7:
When using the programmable PAD (CM35 
YY=19, 2nd Data=0-3), assign the PAD data.(1)
(2)50-65
00-15
T/R: Transmitter PAD/Receiver PAD
+: Gain
–: Loss
CM35
B
CM42
END
CONNECTION 
PAT T E R N SPAD DATA OF DTI [dB]
DATA
=4 (T/
R)DATA
=5 (T/
R)DATA
=6 (T/
R)DATA
=7 (T/
R)
Station – DTI–3/–8–3/–3–3/–3–3/–8
Tone – DTI 0/0 0/0 0/0 0/0
COT/LDT – DTI 0/0 0/0 0/0 0/0
ODT – DTI +3/–3 0/0 0/0 +3/–3
DTI –DTI 0/–60/00/–60/0
See the following tables.
PAD DATA PATTERNS
CONNECTING
PATTERNS CM35 YY=19
2ND DATA=0CM35 YY=19
2ND DATA=1CM35 YY=19
2ND DATA=2CM35 YY=19
2ND DATA=3
50
6550 54 58 62 STA/TONE-DTI
51 55 59 63 COT/LDT-DTI
52 56 60 64 ODT-DTI
53 57 61 65 DTI-DTI
PATTERN
1ST
DATA
~
PAD DATA OF DTI (T/R) [dB] REMARKS
00
1500 0/0
01–2/–2
02–3/–3
03 0/–6
04–3/–8
05 +3/–3
06–6/–6
07–8/–8
08
15Not Used
PATTERN
2ND DATA
~
~ 
						

							ND-46248 (E) CHAPTER 4
Pag e 15 3
Revision 2.0
SYSTEM DATA PROGRAMMING
2. DCH Assignment
DESCRIPTION DATA
Assign an AP number to the DCH card (PN-
SC01).
The AP number assigned must coincide with 
the value set by the SENS switch on the PN-
SC01 card.(1)
(2)AP No. (04-15)
35: DCH for Roaming
Assign the DCH number to the AP number of 
DCH assigned by CM05.
(1)
(2)YY=08
DCH No. (0-4)
XX: AP No. assigned by CM05
Execute CM35 YY=90 for the B channel route 
and D channel route.
(1)
(2)YY=90 (Special Facilities)
B Channel, D Channel Route No. (00-63)
6: PBX-PBX Interface.
Assign the DCH number to the voice channel 
trunk route assigned by CM30 YY=00.
(1)
(2)YY=93 (Assignment of D Channel Han-
dler)
B Channel Route No. (00-63)
00-04: DCH No. (0-4)
15 : Not usedCM05 START
CM06
CM35
A
INITIAL
INITIAL 
						

							CHAPTER 4 ND-46248 (E)
Page 154 Addendum-001
Revision 2.1 MARCH, 1999
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the LAPD Mode of the D channel 
route as “Network Mode” or “User Mode”. 
This data must be set differently between the 
opposite DTIs. When the opposite office is a 
master office, set this data to 1 (User Mode), 
and when the opposite office is a slave office, 
set this data to 0 (Network Mode). 
(1)
(2)YYY=113 (LAPD Mode)
D Channel Route No. (00-63)
0: Network Mode
1: User Mode
Assign the roaming service to each B channel 
and D channel route.
(1)
(2)YYY=140 (Roaming Service)
B Channel, D Channel Route No. (00-63)
0: Available
Provide pursuit function after the roaming PS 
to each B channel route.
(1)
(2)YYY=141 (Roaming PS Pursuit)
B Channel Route No. (00-63)
0: Provided
Specify the protocol type between the PBXs 
as “Q931a-Digital”.
(1)
(2)YYY=142 (Protocol between PBXs)
B Channel, D Channel Route No. (00-63)
1: Q931a-Digital
Assign the trunk number assigned by CM07 
YY=01 to each DCH Number for providing D 
Channel path between DTI and DCH.
Note:Confirm that the SC01 Run LED
is flashing.
(1)
(2)YY=00
DCH No. (0-4)
Trunk No. (000-255)
When the Network Numbering Plan is the 
Open Numbering System, assign the Home 
PBX ID for the indication on the PS/D
term.
(1)
(2)YY=01
DCH No. (0-4)
X-XXXX: Home PBX ID
(1-4 digits, Decimal)
CM35
END
CMA9
A
AP INITIAL
AP INITIAL
INITIAL 
						

							ND-46248 (E) CHAPTER 4
Pag e 15 5
Revision 2.0
SYSTEM DATA PROGRAMMING
3.7.3 Home PS Data Assignment
DESCRIPTION DATA
Assign an AP number to the DBM (Data Base 
Module) card (PN-AP00).
The AP number must be coincide with the val-
ue set by SENSE switch of the card.(1)
(2)AP No. (04-15)
34: DBM (AP00)
Assign the Trunk Restriction Class for Home 
PS. This data is sent to the visitor PBX when 
the PS is roaming.
Note:When the location registration of
a Visitor PS is executed, the
Trunk Restriction Class assigned
on the Home PBX is notified to
the Visitor PBX being substituted
as follows.
(1)
(2)YY=01 (Trunk Restriction Class)
X-XXXX: Virtual LC Station No.
XY
X: Trunk Restriction Class in Day Mode
(1 -8)
Y: Trunk Restriction Class in Night Mode
(1 -8)
1 : Unrestricted (RCA)
2 : Non-Restricted 1 (RCB)
3 : Non-Restricted 2 (RCC)
4 : Semi-Restricted 1 (RCD)
5 : Semi-Restricted 2 (RCE)
6 : Restricted 1 (RCF)
7 : Restricted 2 (RCG)
8 : Fully-Restricted (RCH)
Assign the Service Restriction Class for Home 
PS.
Note 1:Different Service Restriction
Class for Multi-Site Roaming
must be assigned to the PSs ac-
cording as whether the PS is
used for Roaming.
(1)
(2)YY=02 (Service Restriction Class)
X-XXXX: Virtual LC Station No.
XXYY
XX: Service Restriction Class A 
(00-15 )
YY: Service Restriction Class B 
(00-15 )
Assign the Tenant Number to the Home PS. 
This data is sent to the visitor PBX when the 
PS is roaming.
Note 2:It is recommended to assign the
PS station (CM1C) and its relat-
ed virtual LC station number to
the same service restriction class
when roaming is provided. See
Section 3.3.
(1)
(2)YY=04 (Service Restriction Class)
X-XXXX: Virtual LC Station No.
00 -63 : Tenant No. 00-63
01 
CM05 START
CM12
A
INITIAL
CM12 YY=01 Settings
on the Home PBXNotified Class
1: Unrestricted (RCA) 1
2: Non-Restricted 1 (RCB) 2
3: Non-Restricted 2 (RCC) 3
4: Semi-Restricted 1 (RCD) 4
5: Semi-Restricted 2 (RCE) 4
6: Restricted 1 (RCF) 5
7: Restricted 2 (RCG) 5
8: Fully-Restricted (RCH) 6 
						

							CHAPTER 4 ND-46248 (E)
Pag e 15 6
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the Service Restriction Class for 
Roaming Service download.
Note:Assign the same Service Restric-
tion Class data to the Virtual LC
Station number and the PS Sta-
tion number (See Section 3.3) for
Roaming Service.
(1)
(2)YYY=117
00-15: Service Restriction Class A 
Assigned by CM12 YY=02
0 : Allowed
1 : Restricted
Specify whether the Home PBX Numbering 
Plan is the Open Numbering System or Closed 
Numbering System. This assignment defines 
whether the Home PBX ID is added to the 
Roaming Number, and to the Originating 
Number sent to the Visitor PBX.(1)
(2)088 (Home PBX Numbering Plan)
0 : Closed Numbering System
1 : Open Numbering System
END
CM08
A
CM15