Mitel Voice Processing Solutions Installation And Service Manual

hissnd and so it will consider the link down. When hissnd successfully resta& and attaches it’s name,
hisrcv and hismwi can locate it and link communication will proceed as expected.
“HISRCV: Unable to read eeco OAA record”(Internal error, report condition)
-*Error condition causes abort, error displayed on console and task restart+
This data is logged when hisrcv is started and it is not able to 
read from disk the conf?guration data set by
hiSmUlU.“HISRCV: Use hissnd 
$port [+hyatt]”
(Lntemal error,...

out the specific message waiting packet. The task hissnd completes the packet transfer and replies to
bismwi.At this time 
the CDR message is logged and hismwi replies to mwla.
“HISMWI: MWI off for station number (x)”
(Normal operation)This data is logged after the following task 
communication compietes.The task mwla request.3 hismwi to
send a message waiting request for station number 
(x). The task hismwi in turn quests hissnd to send
out the specific message waiting packet.
The task hissnd completes...

This data is logged when hisruqmc needs hissnd to send a resync message to the PMS system. The task
hisresync returns to hisrcv without completing the command.
“HISRESYNC: Unable to send to hissnd, data Iost”
(Internal error, message lost, sport condition)
This data is logged when hisreqnc needs hissnd to send &ta Aowing the link to stay active but the task
hissnd can not be found by name.The data is lost and hisresync returns to hisrcv without 
compieting the
command.
“EISRESYNC: Unable to re-send to...

Issue 1 Release 2.0 January 19961Voice Processina Solutions 1JI
IU, @ - Trademark of Mite1 Corporation
0 Copyright 1996, Mite1 Corporation
All rights reserved.
Printed 
in Canada.
ITNPP Installation
and Configuration
MITEa‘.
i 

0 1996 Centigram Communications Corporation. All rights reserved.
This publication is protected by federal copyright law. No part of this
publication may be copied or distributed, stored in a retrieval system, or
translated into any human or computer language in any form or by any means
electronic, mechanical, magnetic, manual or otherwise, or disclosed to third
parties without the express written permission of Centigram Communications
Corporation, 91 East Tasman Drive, San Jose, CA 95134.
REPRODUCTION...

.Tefocator Network Paging Protocol 
(TNPP)installation and Configuration
INTRODUCTION
*.TNPP is a standard data communications protocol that is used for communications
between paging terminals or other types of equipment required to implement a paging
system network.
The implementation of support for this protocol on 
VoiceMemoallows message waiting notification for mailboxes to be done by sending a TNPP page
packet over a serial link to a Paging Terminal. The Paging Terminal delivers the page
via the...

SOFTWARE CONFIGURATION
There are two areas of VoiceMemo that need configuration information for TNPP to
operate. These areas are the Offline menu and Mailbox configuration.
The Offline Menu
To configure the Offline portion of 
TNPP, choose the RS232 or Smartcard Integrations
selection from the Offline Menu. From the RS232 or Smartcard menu, choose the
TNPP Paging option.This is the main configuration menu for TNFP. The fustselection that must be made is to choose the host that the 
TNPP application will...

RS232 Link Menu
TNPP Link Number
Enter the TNPP link number to be configured
Active
Enter Y or N. TNPP tasks will only be started for links that are
active.Enter Y to make this an active 
TNPP link.
Select Current Serial Port
Enter the name of a 
VoiceMemo serial port that will be used for
this TNPP link. 
($terml, $term2, $ctil...etc.)Pager systems this link supports
Enter the pager system(s) that this TNPP link will support.
The
pager system 
can only support TNPP.Baud rate
1.Enter the appropriate baud...

System Message
Enter a system message. (Example: Call VoiceMemo). This
message will appear on alpha-numeric pagers under certain
circumstances.If a page is not a cut-through page and the
mailbox does not have post-pager digits configured, the system
message will be sent.
Display TNPP System Information
Select this option to display the TNPP System information that
has been configured for each link.
TNPP Timing Parameters Menu
NOTE: The following parameter values represent the defaults recommended in
the...