Mitel Voice Processing Solutions Installation And Service Manual

Timeout on idle link for keep alive ENQ (tidle)
This parameter represents the amount of time that a TNPP link
can be idle before VoiceMemo will send an ENQ.
Number of retries by sending station per packet (Cretry)
This parameter represents how many times 
VoiceMemo will
make on a packet that has been 
NAK’d.Re-transmits in response to RS holdbacks (Chold)
This parameter represents the number of times that 
VoiceMemowill re-send a packet that an RS has been received on.
Number of ENQ retries before error...

lFor modifying a mailbox already configured for TNPP:
At the “Modify TNPP fields?” prompt enter y.
lFor deleting existing TNPP configuration information:
At the “Delete TNPP fields?” prompt enter y.
l At the 
“TNPP CAP or ID paging:”
prompt, enter either CAP or ID
depending on what type of paging will be done for this mailbox.
Mailbox Parameters:
Message Waiting type 
#l (or #2)Enter message waiting type 5 for Pager.
Pager Access Code Index
8.Enter the TNPP Pager system index number that was configured...

TNPP CAP codeThis prompt is displayed
(see above). Enter the 8
mailbox owner’s pager.TNPP ID codeif CAP paging was selected for this mailbox
characters that represent the CAP code of the
This prompt is displayed if ID paging was selected for this mailbox (see
above).Enter 
the 10 characters that represent the customer ID to be
paged
TNPP Page typeThis prompt is displayed if CAP paging was selected for this mailbox
(see above). Enter the value that represents the signaling code scheme of
the mailbox...

Use the lights test from the System Maintenance Menu, Additional Options
selection. Send an “On” to the mailbox.
Result:The mailbox’s pager should receive a page and continue
receiving pages at the configured interval until the configured page
frequency has been exhausted or an “Off’ has been sent. The pager will
display the Post-pager digits (if they were configured) or the System
Message (if it was configured).
Leave messages for the mailbox
Result:The mailbox’s pager 
shouId receive a page and...

lMake sure the RS232 connection between VoiceMemo and the Paging Terminal
is correct and that the link communication attributes 
are correct on each device.
(baud rate, etc.)l Check the 
logfile for any messages that could indicate the problem. For
example, if a mailbox’s pager system index refers to a 
TNFP link configured
for CAP paging and the mailbox is configured for ID paging, an error message
will be logged.lMake sure that the pager information configured in the mailbox is consistent
with the...

Configuration Adjustment MenuNOTE: Configuration changes made here are run-time and will NOT be
retained if the system reboots.Any permanent changes must be made in the
Offline TNPP configuration menus.
Modify 
RS232 Link MenuIn 
this menu there are several RS232 Link attributes that can be
changed during run-time. The items that can be modified are:
Pager Systems Supported
Number of data bits
Number of stop bits
ParityAfter the item(s) to be changed have been 
selr;cted, the Send
changes to TNPPADMIN...

Issue 1 Release 2.0 January 19961 VoiceProcessing
Solutions )TM, 
Q -Trademark of Mite1 Corporation
0 Copyright 1996, Mite1 Corporation
All rights reserved.
Printed in Canada.
1PBX Integration
SX-2OF DIGITAL PABX
SX-200 LIGHT PA&
‘;,‘;...;. ::‘f/.  .  .  .“‘::::L..: .‘C :. .,,.. :.,:. .;.i;..:!‘L.:,,,/ :;;iz..,
MITEL”
. .::::.,.‘;” ,.ijjj : ,.
.:$,: ‘.,:;‘.;,” ;..:: ,:.’ ..:.:.: s,;. ‘::. j/ :;. .’:. ..’
: ‘:
.::: ::., ;j: ,, .:ii:: :..: .,
:‘- 

Contents1.OVERVIEW . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
2.GENERAL . . . . . . . . . . . . . . . . . .._.........._......._.............-............................................................... 3
3.REQUIREMENTS/LIMITATIONS. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ....

MITEL MAILTM Enhanced In-Band Integration
(Software Rev. 6.OB) on
SX-200@ DIGITAL and SX-200 LIGHT Systems
1.OVERVIEW
This document is intended to show the necessary hardware connectivity to the MITEL SX-200@DIGITAL PABX and the SX-200 LIGHT PABX, as well as to define the Customer Data Entry
(CDE) requirements to integrate the MITEL MAILTM Enhanced In-band application with the PBX.
2.GENERAL
Full integration between the M/TEL MA/L system and the SX-200 is achieved through the use of
the “Enhanced...

4.HARDWARE INTERFACE
(Refer to Figure 1)l
The M/TEL MA/L system interfaces to the SX-,200 family of PABXs via ONS lines.l
Receptionist II ports use shared ONS lines which are programmed in the same Hunt Group
on the PABX.l
Message Waiting port(s) require a dedicated ONS line that is a member of a hunt group. This
hunt group is NOT the same as 
VoiceMemo ONS lines hunt group.l
Pager Notification and FaxMemo also have separate line port(s).SX-200 
DIGITAULIGHTONS Voice Mail Hunt Group 4
Access Code...