Mitel Voice Processing Solutions Installation And Service Manual

Dual El Offline ConfigurationPage 1 of 4VoiceMemo Release 6.OA and later
Though typically a factory-installed standard feature, the El digital trunk connectivity
feature may be retrofitted to a system in the field.Use this procedure if you are adding a
Dual El Digital Trunk Interface card to a Series 6 server that you already have.
This procedure gives you the instructions for configuring the feature software to support
a El digital trunk. El trunk configuration is done offline using the Resource...

a? 3151
Page 2 of 4
VoiceMemo Release 6.OA and later
Step
4.Exit back to the Resource Configuration Menu when done.
5.At the Resource Configuration Menu, identify the logical number of the module.
This number is either 
1, 2, 3 or 4.
Select:(M) set Module number
P~-ompt: Input Module #:
Response: 1, 2, 3, or 4.
6.At the Resource Configuration Menu, configure the Dual El Digital Trunk
Interface card.*.
Select:(C) Card Configuration
Prompt: Occupied slots are:. .SlotCard---- ----
---- ----
xxDUAL El
Input...

cl? 3151
Page 3 of 4VoiceMemo Release 6.OA and later
Step13. At the Configure Frame Format for [DUAL El] in AT slot x Trunk y (where “y” is
the trunk number you entered in step 1 I), select the framing format you want for
the trunk. You can set the trunk for CEPT framing or for CRC framing.
Because you have not yet set the trunk coding format, the default HDB3 coding
appears in the confirmation.
Also, because CCS is the only signaling 
tyPe available
for El trunk connectivity, CCS appears in the...

cl? 3151Page 4 of 4
VoiceMemo Release 6.OA and later
Step
El/El Carrier configuration:
Trunk: 0Configuration: CEPT CRC, HDB3, CCS
Trunk: 1Configuration: CEPT CRC, HDB3, CCS
----------Trunk Type for each channel:
Chnl:000102030405 06 0708091011121314Type: CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS
Chnl:151617181920 21 2223242526272829Type: CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS
Chnl:303132333435 36 3738394041424344Type: CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS CCS...

Change the Digital Trunk Connectivity ClockReference
CP 3152
Page 1 of 1
VoiceMemo Release 6.OA and later
In addition to the clock reference selection in the offline digital trunk configuration, the
clock reference can be changed through the Digital Connectivity Maintenance Menu.
Step
1.Reach the Digital Connectivity Status/Maintenance Menu.
2.Change the module clock reference.
Select:(C) Change module clock reference
Prompt: Module Holding digital board(s):Response: The number of the module in which the...

CP 3153Monitor Digital Trunk StatisticsPage 1 of 2
VoiceMemo Release 6OA and later
The ability to monitor digital trunks gives statistical data on trunk operation as it affects
voice messaging. This data is valuable for network management and for Series 6 server
maintenance.The trunk monitor display gives performance statistics totals for the period current the
most recent second as indicated by the time and date stamp on the display. The display
The trunk information presented and the statistics...

CP 3153
Page 2 of 2
VoiceMemo Release 6.OA and later
StepReference
3.Press Q to return to the Digital Connectivity Status/ Maintenance Menu.
4. Monitor all digital trunks.
Select:(A) Monitor all trunks.
Prompt Host holding digital board(s):
Response:The number of the module.
Prompt: Reset counters (Y/N):
Response: As required, Y
The system presents the information shown in Step 2.
5.When done monitoring the trunks, exit to the Main Menu. 

cl? 3154Put Digital Trunk Out of Service
Page 1 of 1
VoiceMemo Release 6.OA and later
Digital trunks can be placed into and out-of-service 
(00s) for maintenance purposes.
When a trunk is placed OOS, the digital trunk interface card automatically sends an 
AISto the far end to indicate the 
00s state of the trunk.
SteDReference
1.Reach the Digital Connectivity Status/Maintenance Menu.
2.Place a trunk out-of-service.
Select:(D) Place trunk out-of-service
Prompt.- Module holding digital board(s) :...

CP 3155Place a Digital Trunk Into ServicePage 1 of 1
VoiceMemo Release 6.OA and later
Digital trunks can be placed into and out-of-service 
(00s) for maintenance purposes.
When a trunk is placed OOS, the 
digital trunk interface card automatically turns off the
1.Reach the Digital Connectivity Status/Maintenance Menu.
2.Place a trunk into service.
Select:(E) Place trunk out-of-service
Prompt: Host holding digital board(s):
Response:The number of the module.
Prompt:Trunk number:I
Response:The number of...

Tl/El Menu,Map 13
Physical Resource Configuration Menu
(A) Add resource card
Add Board to Database Menu
(A) Dual 
Tl
(B) AG (24/30)
(C) AG 8
CD) A?-‘I
(E) CGRM 2
(F) DUAL El
(G) MTP Processing
(H) Analog FAX
(I) M-VIP FAX (2/4/8)
(X) exit
(C) Card configuration
Configuration Menu for Board [ 
] in AT slot xx
(A) IO Port Address change
Select IO Port Address Menu
(A) 0x300
(B) 0x2300
(T) set Trunk signalling type
Select Trunk Type Menu(0) 
Analog-E&M(1) 
Analog-E&M Type 1A(2) 
Analog_Loopstart(3)...