Mitel Voice Processing Solutions Installation And Service Manual

Dual Tl Digital Trunk Connectivity
1--811Model 70 and Model 
1201 supports only one digital trunk for a maximum system
capacity of 24 
KM voice channels. The Model 120s and the Model 640 module
each supports up to 60 PCM voice channels between two digital trunk interface
cards.You assign the slot at the Physical Resource Configuration Menu for the card you are
configuring.
Module NumberThe module number is the Series 6 server module in which the digital trunk interface
card is installed. A four-module...

Dual T1 Digital Trunk Connectivity
l Loop start
l Ground start
lDirect Inward Dial (DID)
. E&M
You set the trunk signaling in the Select Trunk Type Menu. The menu has options
for both analog and digital trunks. However, when you are configuring a digital
trunk interface card, the configuration manager accepts only the digital trunk
options.
Trunk ConfigurationTrunk configuration includes the trunk number, framing format, and coding format.
Trunk Sequence NumberThe trunk number is the logical number of...

Dual T1 Digital Trunk ConnectivityThen, if the trunk to which the clock reference is derived, the Series 
G server will
automatically switch over to the second trunk on the Dual 
Tl card.
Note:This clock source switchover feature does not work if digital trunk
connectivity is split between two Dual 
Tl cards.
When configuring the system, use the network clock as the system clock reference to
prevent frame slips (Figure 
2-6). However, use the internal clock reference when the
trunks are connected to...

Configuration Task list
Page 1 of 1
VoiceMemo Release 6.OA and later
Procedure
E 1 /Tl ConfigurationChangethe Digital Trunk Connectivity Clock Reference...........................CP
3 152Dual El Offline Configuration...................................................................cl? 3151
Dual T 1 Offline Configuration..................................................................
cl? 3150
Monitor Digital Trunk Statistics................................................................
CP 3153
Place...

cl? 3150
Dual 
Tl Offline ConfigurationPage 
1 of 6
VoiceMemo Release 6.OA and later
Though typically a factory-installed standard feature, the Dual 
Tl digital trunk
connectivity feature can be retrofitted to a Series 6 server in the field. Use this procedure
if you are adding a Dual 
Tl Digital Trunk Interface card to a Series 6 server that you
already have. This procedure presumes that you have already set the card jumpers and
switches and installed it in the Series 6 server.
This procedure gives you...

cl? 3150
Page 2 of 6VoiceMemo Release 6.OA and later
Step
1.Reach the offline Resource Configuration Menu.
2.Add a resource card number.
Select:(A) Add resource card
Prompt: Available slots are: x x x 9 x 11 x x x
Input your choice:
Response: The card number according to the Model of the Series 6 server (refer to
the following Series 6 server matrix for Model 640 and Model 
120.9.For Model 1201, type 6. For Model 70, type 3.
Slot No.
8
9
10
11
12
13
14
15Slot No.
4
5
-
6
7
8
9
10
11Model 640 (60...

cl? 3150
Page 3 of 6
VoiceMemo Release 6.OA and later
Step
*DSPS modules installed only if DSP24-1 not present. Cards can e a mix of DSP8/24s and
LC8s so long as total ports per module does not exceed GO.Only count number of Tl channels
enabled (Fractional 
Tl). Fax ports are not included n the total port count. The confirmationmessage Board [DUAL 
Tll is added to slot x,where “x istheslot
number you added in Step 1 above.
3.At the Add Board to Database Menu, add the digital trunk interface card. Exit...

. . .
CP 3150
Page 4 of 6
VoiceMemo Release 6.OA and lat’er
Step9.At the Configuration Menu for 
Tl /El Carrier at trunk 0, set the logical number of
the trunk.Trunk configuration consists of setting the trunk number, framing, and
coding.
Select:(T) set Trunk number
Prompts Input your choice, ? for help
(T/F/C/D/?):
Response: 0 or 1
10. From the Configuration Menu for 
Tl/El Carrier at trunk 0, reach the Configure
Frame Format for Board [DUAL 
Tl] in AT slot x Trunk 0 Menu.0.11. At the Configure Frame...

cl? 3150
Page 5 of 6VoiceMemo Release 6.OA and later
Step16. At the Select Trunk Type Menu, select the signaling associated with the PCM
channels you selected in Step 15. You can select only the options for digital trunks.
If you select signaling for analog signaling, you get the error message “Can not set
Analog trunk 
type to Digital Trunk.”
Select:(4) Digital-E&M, (5) Digital-Loopstart, (6) Digital-DID, or (7)
Digital-Groundstart
PT-0FZp t:Input your choice, ? for help...

CP 3150Page 6 of 6
VoiceMemo Release 6.OA and later
Card: DUAL Tl
IO Port Address: OX300
Resources: (48) Net-Dat; (48) Net-Sig;
---____---
Tl/El Carrier configuration:
Trunk: 0Configuration: 
D3/D4, BBZS, CAS
Trunk: 1Configuration: D3/D4, AM1 ZCS, CAS----------
Trunk Type for each channel:
Chnl:
0001020304 05 060708091011
Type:E&M E&M E&M E&ME&M LS LS LS LS LS LS LSs.
Chnl:1213141516 17 181920212223
Type: LSLS LS LS LS LSLS LSLS LS LS LS
Chnl:24
25262728 29 303132333435
Type: LSLS LS LS LS LS LS LSLS LS...