Mitel Voice Processing Solutions Installation And Service Manual

Omni
See the Receptionist II manual for more information about programming for
Receptionist II.
VoiceMemo Template SpecificationsThe Omni templates have a default inter-digit timeout of four seconds and are set to
hangup on an error condition. Without actually editing the templates, you can
change the inter-digit timeout and the error action by using the Omni Edit
Parameters Menu.
The Enhanced In-band Integration optional feature includes 
two template sets for
Omni integration, one for a three-digit...

OmniT9: 08 Xx# d3 0#, T V4, 40, H
Next:
Comment: Trunk call Busy forward
TlO:09 Xx# d3 0#, T V3, 40, H
Next:
Comment:Trunk call 
RNA forward
Tll:lXx# d3 O#, T V3, 40, H
Next:
Comment:Command code 
lo-16 will have the same greeting
B-5i 

Appendix C:System 25 Enhanced In-band IntegrationThis appendix contains supplemental information about integrating an AIP
VoiceMemo system with an AT&T System 25. See the Task List for procedures to
configure the integration.
Features and FunctionsThe System 25 integration operates over standard two-wire circuits from Tip and
Ring cards. The switch routes direct and forwarded calls to the 
VoiceMemoapplication over one group of lines. The 
VoiceMemo system sends message waiting
requests to the switch...

System 250Pager and Message Delivery Message Waiting (Type 5) - uses one or
more 
VoiceMemo line ports to outdial to external paging systems or
telephone numbers.
System 25
Incoming
Trunks
Station
Forwarding
\\\
Y- - ) Queue-
/.
/
Circular
Hunt Group-
ou;Ql;;k;t- _-----_-_t
AIP VoiceMemo System
Integration PortsD
II MODEM
Message Waiting Port(s+----------.
Outdial Ports4Enhanced in-band
and Receptionist II
Applications
W-232
Message Waiting*.
or
DTMF-to-PBX
Message Waiting
Outdials:
Paging, Fax,
Call...

System 25The AT&T System 25 software requirements are:
0R2Vl (Release 2, Version 1)
0R3Vl (recommended)
The System 25 hardware requirements are:
lOne (1) ZTN-78 port per VoiceMemo/Receptionist II port
0One (1) ZTN-78 port for message wait control
Use of Receptionist IIThe System 25 integration allows the optional Receptionist II application to perform
supervised transfers. The switch can recognize a switch-hook 
flagh on the line and
return dial tone. The Receptionist II port then dials the desired DN...

System 25
Comment:External Forwarded call
T6:# 08## dx#, ~30 H, 50, H
Next:
Comment:Port badcall from the switch
c-4 

Appendix D:Norstar Enhanced In-bandlntearationThis appendix contains supplemental information about integrating an AIP
VoiceMemo system with a Northern Telecom Norstar KSU.See the Task List for
procedures to configure the integration.
Features and FunctionsThe 
Norstar integration operates over a group of digital lines that is equipped with
VMI (Voice Mail Interface) modules. The switch routes direct 
&d forwarded calls
to the 
VoiceMemo system over one group of VMI lines. The VoiceMemo system
sends...

Norstai
0Pager and Message Delivery Message Waiting (Type 5) - uses one or
more 
VoiceMemo line ports to outdial to external paging systems or
telephone numbers.
NorstarAIP VoiceMemo System
x VMIEl:integration Ports) Enhanced In-band
)andReceptionist II
* A VMI can also be used for
the Message Waiting interface3009EIE
Figure D- 1Norstar Integration Structure
Hardware and Software RequirementsThe AIP 
VoiceMemo system software requirements are:
0Release 5.02 or later
0Enhanced In-band Integration optional...

Norstar
Feature Interactions and limitationsThe following 
interactons and limitations may affect the integration of a
VoiceMemo system and a Norstar KSU.
The DR2 does not support Call Forward Busy.
The Compact DR2 has no Call Forward No Answer.
The DR3 and DR4 support Call Forward Busy if the station is in use on
any line.Call Forward Busy is a system-level option.
Call Forward No Answer means that the ICM rings several times and
then the call goes to a VMI.
A 
Norstar can support up to ten VMIs.The...

Norstar
lProgram the VoiceMemo system to recognize the extension numbers of
the ports running the Receptionist II application (DP 6034).
l
Program the 
VoiceMemo ports to dial a DTMF # when the system
identifies a call forwarded from one of its own ports.
lSet line exception 9 for ringing timeout to be greater than the Norstar’s
Forward No Answer timer.
See the Receptionist 
IIManual for more information about programming for
Receptionist II.
VoiceMemo Template SpecificationsThe template sets for...