Mitel Voice Processing Solutions Installation And Service Manual

Task List
Page 1 of 1
VoiceMemo Release 5.03 and 5.04A and later
TuskProcedure
Enhanced In-band Integration
Configure an Enhanced In-baud Integration......................................GP502
Configure AT&T Legend Integration.................................................GP508
Configure AT&T System 25Integration.............................................Gl? 506
Configure Fujitsu Omni Integration...................................................GP504
Configure Fujitsu Starlog...

Configure an Enhanced In-band IntegrationPage 1 of 1VoiceMemo Release 5.03 and later
This procedure describes the steps required to configure your AIP 
VoiceMemo system
with Enhanced In-band Integration. These steps include a Detailed Procedure that is a
sample for reference when creating in-band templates for use with your particular switch.
Use this procedure if there is no default template set available for your switch.
Step
1.
2.
3.
4.
5.
6.
7.
8.Install the Enhanced In-band Integration optional...

GP504Configure Omni IntegrationPage 1 of 8
VoiceMemo Release 5.03 and later
This procedure summarizes the steps required to install and configure the Enhanced 
In-band Integration to work with the Omni PBX. Refer to the appendixes for reference
information about this integration.
There are two sections to installing this integration: installing and configuring the
software on the 
VoiceMemo system, and configuring the Omni PBX. Refer to your
Omni documentation for help when configuring the PBX, if...

GP 504
Page 2 of 8VoiceMemo Release 5.03 and later
step
9.If your VoiceMemo system has Release 5.03 software, set the number of in-band
tasks per module to 20% of the number of in-band ports in each module.If your
system has Release 5.04 software, the system automatically configures the required
number of tasks.
10. Set the following phone 
line exceptions for each line in the line group:
Excention Value Descriution08 10 Dead Line Time-out
24 YEnable Wink Start signaling
32 20 Received DTMF 
Debounce35...

GJ? 504
Page 3 of 8VoiceMemo Release 5.03 and later
Stev
5.Use the following RC transactions to add the hardware to the system data base.
Select double-height slots to accommodate the EMT cards.
RC 221Add a Card
CARD
CARDTYPEFB NUMBER
---- ---------
EMTFB-17201RC 153Add a Trunk
*.
VoiceMemoMessage Wait
TrunksTrunk
Physical Trunk Type
E&ME&M
Supervisory IncomingWinkID
Supervisory Outgoing
Wink--
@D Configure Trunks for the Enhanced In-band line Group
6.Use the following RC transactions to add the Enhanced...

GP 504
Page 4 of 8VoiceMemo Release 5.03 and later
SteDRC 212
H
OF
OLKA
s sWH
---
YRC211
STA
AC
TC
IE
0 sNS
---
YChange/Show Non-Displayable Class of Service 1
R
ECD AP
EI DH
ID MO
vIN
ENE
--- ---
YN
Change/Show Displayable Class of Service 1
A
0TCN
OC M M
LE E EN
LS R RE
s s ST
--- --- ---
Y
YY
7.Use RC 218 to assign a directory number for the Enhanced In-band trunk group.
This DN is the destination for all forwarded calls. If your system has the
Receptionist II application, it is also the termination...

GP 504
Page 5 of 8VoiceMemo Release 5.03 and later
Step
8.Use RC 113 to create a “dummy” extension, and then forward that extension to the
DN for the Enhanced In-band trunk group with RC 
141. This extension is the
number that users must dial to retrieve their messages. You should select an 
easy-to-remember number for this extension.
DIR
--cos--DIV DIV
DIV
NUMDNCND DST ID-_------_____---~_--------~~~~~~~YY zzDA VM
WhereXXX is the DN for message retrieval from step 7
YY/ZZ is the Basic Class of...

G-l? 504
Page 6 of 8
VoiceMemo Release 5.03 and later
StepReferenceRC 212Change/Show Non-Displayable Class of Service 1
RH
EOF CD AP 00
OL EI DH RN
KA ID MO IL
ss vIN GY
WH ENE
--- --- --- ---
NNYYRC 211
Change/Show Displayable Class of Service 1
STAA
0AC TCN
TC OC M M
IE LE E EN
OS LS R RE
NSS S ST
--- --- --- ---
NNNN10. Set the following values for the E 
& M trunk groups. These fields are not accessible
through RC transactions.
T5841Trunk Group outpulsing delay value = 0
T575 1Trunk Group AIOD...

GP 504
Page 7 of 8VoiceMemo Release 5.03 and later
step
ED Configure User Stations11. 
Allow user stations to forward to the VoiceMemo system and receive message
waiting indication with the following RC transactions.
RC 212Change/Show Non-Displayable Class of Service 1
CVM
AAA
LR
ILI
LFA VB
WB MO
DL SX
-__ ---
YY
RC 214Change/Show Non-Displayable Class of Service 2
MESSAGE
WAITING
LAMP---_---
Y12. Change all user 
COSs with RC 211 to ahow access to the Enhanced In-band trunk
group.
13. Use the following...

GP 504Page 8 of 8
VoiceMemo Release 5.03 and later
Step15. Forward POTS telephones to the 
VoiceMemo directory number with RC 141.
lSelect the condition for forwarding, most likely “Divert if Busy or No Answer.”
lSelect “VMS” as the Destination Type.
16. Tell users with 
FeaturePhones to forward their phones to the VoiceMemo DN.
17. Force the E 
& M trunks out of service and put them back into service using
Maintenance mode.
Reference18. Instruct users to dial the “dummy” extension and enter their...