Mitel Voice Processing Solutions Installation And Service Manual

Configure Fujitsu Starlog IntegrationPage 1 of 3VoiceMemo Release 5.03 and later
This procedure summarizes the steps required to install and configure the Enhanced 
In-band Integration feature to work with the Fujitsu 
Starlog PBX. Refer to the appendixes
for reference information about this integration.
There are two sections to installing this integration: installing and configuring the
VoiceMemo software, and configuring the Fujitsu Starlog PBX. Refer to your Starlogdocumentation for help when...

GP 505
Page 2 of 3VoiceMemo Release 5.03 and later
Step
7.Set the following phone line exceptions for each line in the line group:
Exception Value 
Descriotion3 2 Dial Tone Detect Time
9 20 Ringing Timeout
25 Y Enable DTMF Column 3
14040 Loop Break Detect Time
14490 In-ring Off Time
148 3In-ring On Time Low
152 1500In-ring Minimum Power
1648 DTMF Output Duration
1762 DTMF Output Level
Note:If the VoiceMemo system has the Receptionist II optional feature, the
Ringing Timeout (line exception 9) must be 3...

GP 505
Page 3 of 3VoiceMemo Release 5.03 and later
Step
3.CMC 102:
FLGN
2
15
49
109
110
111
112
136Set the following system parameter flags to the indicated values:
Value
Descrintion
1OPS ring pattern = station ringing (1s on, 3s off)
1Enable message waiting for all 500/2500 sets
10Send filler digit (0) to VoiceMemo when required
1Enable called party auto-disconnect on hangup
1Enable stutter dial tone if no message waiting lamp
0Set voice mail integration pattern zero (0)
3 or4Set to extension length on...

Configure AT&T System 25 IntegrationPage 1 of 1VoiceMemo Release 5.03 and later
This procedure summarizes the steps required to install and configure the Enhanced 
In-band Integration optional feature to work with the AT&T System 25 PBX. Refer to the
appendixes for reference information about this integration.
After completing the steps below, you will need to program your switch to pass in-band
call information to the 
AIP VoiceMemo system. Refer to your PBX manual for
additional information.
SteD...

Configure Northern Telecom NorstarIntegrationGP 507Page 1 of 4
VoiceMemo Release 5.03 and later
This procedure summarizes the steps required to install and configure the Enhanced 
In-band Integration feature to work with the Northern Telecom 
Norstar KSU. Refer to the
appendixes for reference information about this integration.
There are two sections to installing this integration: installing and configuring the
VoiceMemo software, and configuring the Norstar. Refer to your Norstardocumentation for help...

GP 507
Page 2 of 4VoiceMemo Release 5.03 and latei
step
I7.Refer to the Task List in your 
VoiceMemo Reference and Corzfguration Manual to
find procedures to configure any of the options below for the integration line group.
You can reach these options by selecting Other Features from the online Enhanced
In-band Menu.
lSchedule Company Greetings
lEnable Call Placement Message Delivery
lConfigure for Transfer to System Attendant
lDefine an Administrator’s Mailbox
lDefine an Attendant’s Mailbox
l Configure...

GP 507
Page 3 of 4VoiceMemo Release 5.03 and later
Step
GD Configure the Northern Telecom Norstar
1.Install VMI modules for all integration lines as instructed in the Norstar Voice Mail
Inte$zce Installation Gzriu’e. Connect lines from the Line Jacks on the VMIs to
available telephone ports on the KSU. Connect lines from the Terminal Jacks on
the 
VMIs to line card ports on the VoiceMemo system. Plug in the power supplies
for the 
VMIs. Mount the VMIs on the wall after connecting them to both the KSU
and...

GP 507
Page 4 of 4VoiceMemo Release 5.03 and later
Step
6.For Modular DR3 and DR4 systems, ensure that each VMI DN is configured as
follows:
Under Permissions/Capabilities:Set Lock =NONE
Full Handsfree =NO
Handsfree Answerback 
=NO
Pick Up Group =NO
Page Zone =
NO
Auxiliary Ringer =
NO
*.Hotline 
=NO
Priority Call =NO
Under Line Access:
Answer DN =
NO
Line Pool Access =NO(If a line will be used for outdialing, set to YES.)
Two intercom lines are assigned, with one assigned as the prime line.
7.Program...

Configure AT&T Legend IntegrationGP508Page 1 of 1
VoiceMemo Release 5.03 and later
This procedure summarizes the steps required to install and configure the Enhanced 
In-band Integration optional feature to work with the AT&T Legend PBX.
After completing the steps below, you will need to program your switch to pass in-band
call information to the 
AU? VoiceMemo system.Refer to your PBX manual for
additional information.
smReference
1.Install the Enhanced In-band Integration optional feature diskette....

GP 509Configure Northern Telecom MTX IntegrationPage 1 of 1
voiceMemoRelease 5.03 and later
This procedure summarizes the steps required to install and configure the Enhanced 
In-band Integration optional feature to work with the Northern Telecom MTX switch.
After completing the steps below, you will need to program your switch to pass in-band
call information to the AIP 
VoiceMemo system. Refer to your PBX manual for
additional information.
SteD
1.Install the Enhanced In-band Integration optional...