Mitel Voice Processing Solutions Installation And Service Manual

Connect the Chassis Ground to the Rack-
Mount VoiceMemo System
1~3021Page 1 of 1
VoiceMemo Release 5.03 and later
This procedure describes how to connect the chassis ground of a 
telenhone switch to the
rack-mount AIP 
VoiceMemo system.
ADANGER!
1FMake sure that all power to the system has been disconnected
prior to performing this procedure. Failure to do so can cause
injury!
Step
1.Locate the grounding stud on the VoiceMemo cooling assembly.
2..For non-central office applications, connect a single...

DP 5402
Install Optional Feature With System OnlinePage 1 of 2
VoiceMemo Release 5.04A and later
The 
proceduredescribes how to install an optional feature with the system online. Be
sure the Optional Feature Diskette(s) and the Module Enable Diskette contain the serial
number(s) for all disk(s) in the system.
CAUTION!If you are loading a revision support disk (RSD), do it after
completion of this procedure.Loading the RSD first, could create
an incorrect configuration.
WARNING!
This process causes the...

DP 5402
Page 2 of 2VoiceMemo Release 5.04A and later
Step6.Exit the 
VoiceMemo Configuration Offline Menu. The system will perform a
system shutdown.
Prompt: Wait for message waiting queues to be empty?
Response: Y to wait for the queue to clear,
N to continue immediately with the shutdown.
The system then completes the shutdown and activates the 
sofixare, returning to
the System Maintenance 
- Additional Options Menu.
Reference
Dot. Rev. A 

Perform an Online Optional Feature
InstallationDP 5402
Page 1 of 2
VoiceMemo Release 5.04A and later
The 
proceduredescribes how to install an optional feature with the system online. Be
sure the Optional Feature Diskette(s) and the Module Enable Diskette contain the serial
number(s) for all disk(s) in the system.
WARNING!This process causes the system to automatically reboot, resulting in
an interruption to call processing. Centigram recommends that
you perform this procedure during periods of low call...

DP 5402
Page 2 of 2VoiceMemo Release 5.04A and later
SteoReference
6.Exit the VoiceMemo Configuration Offline Menu. The system will perform a
system shutdown.
Prompt: Wait for message waiting queues to be empty?Response: Y to wait for the queue to clear,
N to continue immediately with the shutdown.
The system then completes the shutdown and activates the 
sofixare, returning to
the System Maintenance 
- Additional Options Menu.
, 

DP 6028Define a Line Group for Applications
Page 1 of 2
VoiceMemo Release 5.03 and later
This procedure describes how to define a line group for an application.
Step
1.Reach the VoiceMemo Configuration Offline Menu.
A
CAUTION!
aYou may want to copy the active configuration to ensure that the
inactive configuration reflects the configuration that is currently
operating.
2.If desired, duplicating the configuration.8.
Select:(B) Duplicate Active Configuration
Response: The system copies the current (active)...

DP 6028
Page 2 of 2VoiceMemo Release 5.03 and later
Step6. Add the desired lines.
Select:(A) Add Lines to Current Group
Prompt: Enter lines to add =
Response:In a single-module system, the line card number (O-l 5) and portdesignator (A or B) to add to the line group. Any of the formats shown
in the following examples are valid:
Example 
SpeciJes
1:*All lineso-15
All lines8.o-2Lines OA, OB, lA, lB, 2A, and 2B
lB-4Lines lB, 2A, 2B, 3A, 3B, 4A, and 4B
lA,2A,4A Lines lA, 2A, and 4A
2Lines 2A and 2B
In a...

Assign the Enhanced In-band Integration
Application to a Line GroupDP 7006Page 1 of 1
VoiceMemo Release 5.03 and later
This procedure describes how to assign the Enhanced In-band Integration application to
a line group. You must have first defined a line group (DP 6028).
StepReference
1.Reach the VoiceMemo Configuration Offline Menu.
2.From the Offline Menu, go to the 
LineGroup Only Applications Menu.
3.Assign the Enhanced In-band Integration application to the line group.
Select:(G) Group Selected...

Modify an Enhanced In-band Integration
ApplicationDP7011Page 1 of 3
VoiceMemo Release 5.03 and later
This procedure explains how to modify all of the components of an Enhanced In-band
Integration application.Besides instructions for modifying the individual components
of a template, it includes instructions for changing the inter-digit timeout and the error
action without using the edit templates menu.You can change any or all of the values
for an application or template. The changes will take effect...

DP 7011
Page 2 of 3VoiceMemo Release 5.03 and later
Step
8.Change the default error action.
Select:(B) Error Action if digits missing
Prompt: Error Action =
Response: 1 to cause the system to hang up,2 to play a general greeting.
9.Exit to the Enhanced In-band Menu
Select:(X) Exit
@ED Modify Templates
10. Reach the In-band Edit Template Menu.
11. Select a template to edit.
Select:(A) Current Template
prompt: Current Template =Response: The number of the template to edit.
12. Enter the switch data to...