Lexmark T656dne User Manual

							Reading USB drive DO NOT REMOVE
Wait for the message to clear.
Ready
The printer is ready to receive print jobs.
Reattach bin 
Try one or more of the following:
Turn the printer off and then back on.
If the error occurs a second time:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the specified bin.
4Reattach the bin.
5Connect the power cord to a properly grounded outlet.
6Restart the printer.
If the error occurs again:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the specified bin.
4Contact Customer Support.
Touch Continue to clear the message and print without using the specified bin.
Reattach bin  – 
Try one or more of the following:
Turn the printer off and then back on.
If the error occurs a second time:
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the specified bins.
4Reattach the bins.
5Connect the power cord to a properly grounded outlet.
6Restart the printer.
If the error occurs again:
1Turn the printer off.
2Unplug the power cord from the wall outlet. Understanding printer messages151
Downloaded From ManualsPrinter.com Manuals 
						

							3Remove the specified bins.
4Contact Customer Support.
Touch Continue to clear the message and print without using the specified bins.
Remote Management Active DO NOT POWER OFF
The printer settings are being configured. Wait for the message to clear.
Warning—Potential Damage: Do not turn the printer power off while Remote Management Active appears
on the display.
Remove packaging material, check 
Remove any remaining packaging material from the specified location.
Remove paper from all bins
Remove the paper from all of the bins. The printer automatically senses paper removal and resumes printing.
If removing the paper does not clear the message, then touch Continue.
Remove paper from bin 
Remove the paper from the specified bin. The printer automatically senses paper removal and resumes printing.
If removing the paper does not clear the message, then touch Continue.
Remove paper from standard output bin
Remove the stack of paper from the standard exit bin.
Remove paper from 
Remove the paper from the specified bin. The printer automatically senses paper removal and resumes printing.
If removing the paper does not clear the message, then touch Continue.
Replace wiper
Replace the fuser wiper, or try one or more of the following:
Touch Continue to clear the message and continue printing.
Touch Ignore to clear the message, but at the next power-on, the message appears again.
Resetting active bin
Wait for the message to clear. Understanding printer messages152
Downloaded From ManualsPrinter.com Manuals 
						

							Resetting the printer
Wait for the message to clear.
Restoring Factory Defaults
Wait for the message to clear.
When factory default settings are restored:
All downloaded resources in the printer memory are deleted. This includes fonts, macros, and symbol sets.
All settings return to the factory defaults except the Display Language setting in the Setup menu and the custom
settings in the Serial , Network, Infrared, LocalTalk, and USB menus.
Restore Held Jobs?
Try one or more of the following:
Touch Continue to restore all held jobs stored on the printer hard disk.
Touch Do not restore if you do not want any print jobs to be restored.
Routine maintenance needed
The printer needs to have routine maintenance done. Order a maintenance kit, which contains all the items necessary
to replace the pick rollers, the charge roll, the transfer roller, and the fuser.
Securely clearing disk space
The printer hard disk wiping process needs to recover. The message clears when all blocks are cleared.
Serial 
The printer is using a serial cable connection. The serial port is the active communication link.
Some held jobs were not restored
Touch Continue to delete the specified job.
Note: Some held jobs are not restored. They stay on the hard disk and are inaccessible.
Staples  empty or misfed
Load the specified staple cartridge into the finisher to clear the message and continue stapling.
Staples  low or missing
Load the specified staple cartridge in the finisher to clear the message. Understanding printer messages153
Downloaded From ManualsPrinter.com Manuals 
						

							Standard Bin Full
Remove the stack of paper from the standard exit bin to clear the message.
Submitting selection
Wait for the message to clear.
Too many failed panel logins
The printer is now in a lockout mode because:
You attempted to log in too many times with an incorrect PIN
You attempted to log in using an incorrect password number for access to a printer feature, setting, or menu that
you do not have access to.
Note: There is a defined limit on the number of login attempts. Once the limit is reached, this message appears and
the printer enters a lockout mode. The message remains on the printer control panel, and any further attempts to
enter menus is denied until the defined time out expires. The time out duration is set by your system support
person.
Wait for the message to clear once the time out expires, and then:
Enter the correct PIN to access any held jobs
See your system support person if you need a password number to enter a specific printer feature, setting, or menu
that is blocked from your use without the number.
Tray  Empty
Load paper in the tray to clear the message.
Tray  Low
Load paper in the specified tray to clear the message.
Tray  Missing
Insert the specified tray into the printer.
Unsupported disk
An unsupported printer hard disk has been installed. Remove the unsupported device, and then install a supported
one.
Unsupported USB device, please remove
Remove the unrecognized USB device. Understanding printer messages154
Downloaded From ManualsPrinter.com Manuals 
						

							Unsupported USB hub, please remove
Remove the unrecognized USB hub.
USB/USB 
The printer is using a USB cable connection. The USB port is the active communication link.
USB drive removed
Try one or more of the following:
Wait for the message to clear.
Insert the flash drive.
View supplies
This message shows the current level of supplies.
30 Invalid refill, change cartridge
Remove the print cartridge, and then install a supported one.
31 Replace defective cartridge
Remove the defective print cartridge, and then install a new one.
32 Cartridge part number unsupported by device
Remove the print cartridge, and then install a supported one.
34 Short paper
Try one or more of the following:
Load the appropriate paper or other specialty media in the proper tray.
Touch Continue to clear the message and print the job using a different paper tray.
Check tray length and width guides and make sure the paper is properly loaded in the tray.
Check the Print Properties or Print dialog settings to make sure the print job is requesting the correct paper size
and type.
Check that the paper size is correctly set. For example, if the MP Feeder Size is set to Universal, make sure the paper
is large enough for the data being printed.
Cancel the current print job. Understanding printer messages155
Downloaded From ManualsPrinter.com Manuals 
						

							37 Insufficient memory for Flash Memory Defragment operation
Try one or more of the following:
Touch Continue to stop the defragment operation and continue printing.
Delete fonts, macros, and other data in printer memory.
Install additional printer memory.
35 Insufficient memory to support Resource Save feature
Try one or more of the following:
Touch Continue to disable Resource Save and continue printing.
To enable Resource Save after receiving this message, make sure the link buffers are set to Auto, and then exit the
menus to activate the link buffer changes. When Ready appears, enable Resource Save.
Install additional memory.
37 Insufficient memory to collate job
Try one or more of the following:
Touch Continue to print the portion of the job already stored and begin collating the rest of the print job.
Cancel the current print job.
37 Insufficient memory, some Held Jobs were deleted
The printer deleted some held jobs in order to process current jobs.
Touch Continue to clear the message.
37 Insufficient memory, some held jobs will not be restored
The printer was unable to restore some or all of the confidential or held jobs on the printer hard disk.
Touch Continue to clear the message.
38 Memory full
Try one or more of the following:
Touch Continue to clear the message.
Cancel the current print job.
Install additional printer memory.
39 Complex page, some data may not have printed
Try one or more of the following:
Touch Continue to clear the message and continue printing.
Cancel the current print job. Understanding printer messages156
Downloaded From ManualsPrinter.com Manuals 
						

							Install additional printer memory.
42.xy Cartridge region mismatch
Install a print cartridge that matches the region number of the printer. x indicates the value of the printer region. y
indicates the value of the cartridge region. x and y can have the following values:
1US
2 Europe, the Middle East, and Africa
3Asia
4Latin America
9Invalid region
50 PPDS font error
Try one or more of the following:
Touch Continue to clear the message and continue printing.
The printer cannot find a requested font. From the PPDS menu, select Best Fit, and then select On. The printer will
find a similar font and reformat the affected text.
Cancel the current print job.
51 Defective flash detected
Try one or more of the following:
Touch Continue to clear the message and continue printing.
Cancel the current print job.
52 Not enough free space in flash memory for resources
Try one or more of the following:
Touch Continue to clear the message and continue printing.
Downloaded fonts and macros not previously stored in flash memory are deleted.
Delete fonts, macros, and other data stored in flash memory.
Upgrade to a larger capacity flash memory card.
53 Unformatted flash detected
Try one or more of the following:
Touch Continue to stop the defragment operation and continue printing.
Format the flash memory. If the error message remains, the flash memory may be defective and require replacing. Understanding printer messages157
Downloaded From ManualsPrinter.com Manuals 
						

							54 Network  software error
 is the number of the network connection.
Try one or more of the following:
Touch Continue to continue printing.
Turn the printer off and then back on to reset the printer.
Upgrade (flash) the network firmware in the printer or print server.
54 Serial option  error
 is the number of the serial option.
Try one or more of the following:
Check that the serial cable is connected correctly and is the proper one for the serial port.
Check that the serial interface parameters (protocol, baud, parity, and data bits) are set correctly on the printer
and host computer.
Touch Continue to continue printing.
Turn the printer power off and then back on to reset the printer.
54 Standard network software error
Try one or more of the following:
Touch Continue to continue printing.
Turn the printer off and then back on to reset the printer.
Upgrade (flash) the network firmware in the printer or print server.
55 Unsupported option in slot 
 is a slot on the printer system board.
Try one or more of the following:
1Turn the printer power off.
2Unplug the power cord from the wall outlet.
3Remove the unsupported option card from the printer system board.
4Connect the power cord to a properly grounded outlet.
5Turn the printer power back on. Understanding printer messages158
Downloaded From ManualsPrinter.com Manuals 
						

							56 Parallel port  disabled
 is the number of the parallel port.
Try one or more of the following:
Touch Continue to clear the message.
The printer discards any data received through the parallel port.
Make sure the Parallel Buffer menu item is not set to Disabled.
56 Serial port  disabled
 is the number of the serial port.
Try one or more of the following:
Touch Continue to clear the message.
The printer discards any data received through the serial port.
Make sure the Serial Buffer menu item is not set to Disabled.
56 Standard parallel port disabled
Try one or more of the following:
Touch Continue to clear the message.
The printer discards any data received through the parallel port.
Make sure the Parallel Buffer menu item is not set to Disabled.
56 Standard USB port disabled
Try one or more of the following:
Touch Continue to clear the message.
The printer discards any data received through the USB port.
Make sure the USB Buffer menu item is not set to Disabled.
57 Configuration change, held jobs were not restored
Since the time the jobs were stored on the printer hard disk something has changed in the printer to invalidate the
held jobs. Possible changes include:
The printer firmware has been updated.
Paper input, output, or duplex options needed for the print job were removed.
The print job was created using data from a device in the USB port and the device is no longer in the port.
The printer hard disk contains jobs that were stored while installed in a different printer model.
Touch Continue to clear the message. Understanding printer messages159
Downloaded From ManualsPrinter.com Manuals 
						

							58 Too many bins attached
1Turn the printer power off.
2Unplug the power cord from the wall outlet.
3Remove the additional bins.
4Connect the power cord to a properly grounded outlet.
5Turn the printer power back on.
58 Too many disks installed
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the extra disks.
4Connect the power cord to a properly grounded outlet.
5Turn the printer back on.
58 Too many flash options installed
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the excess flash memory.
4Connect the power cord to a properly grounded outlet.
5Turn the printer back on.
58 Too many trays attached
1Turn the printer off.
2Unplug the power cord from the wall outlet.
3Remove the additional trays.
4Connect the power cord to a properly grounded outlet.
5Turn the printer back on.
59 Incompatible output bin 
Try one or more of the following:
Remove the specified output bin.
Touch Continue to clear the message and continue printing without using the specified output bin. Understanding printer messages160
Downloaded From ManualsPrinter.com Manuals