HP Deskjet F735 User Manual

							c. Select the appropriate check boxes to remove the unnecessary components. 
More information about the Disk Cleanup utility 
The Disk Cleanup utility frees hard disk space on your computer by doing the 
following: 
• Deleting temporary Internet files 
• Deleting downloaded program files
• Emptying the Recycle Bin 
• Deleting files from your temporary folder 
• Deleting files created by other Windows tools 
• Removing optional Windows components that you do not use 
d . After selecting the components to remove, click OK. 
5. Install the software. 
To install the software 
a . Insert software CD into the CD-ROM drive of the computer. 
The software installation will start automatically.
NOTE: If the installation does not run automatically, from the Windows 
Start  menu, click Start Search (or Run). In the Start Search (or Run 
dialog box), type  d:\setup.exe, and then press Enter. (If your CD-ROM 
drive is not assigned to drive letter D, enter the appropriate drive letter.)
b . Follow the prompts on the computer screen to install the software. 
6. Try to scan. 
Cause: The software needed to be completely uninstalled and reinstalled.
Unable to print 
Try the following solutions to resolve the issue. Solutions are listed in order, with the most 
likely solution first. If the first solution does not solve the problem, continue trying the 
remaining solutions until the issue is resolved. 
•Solution 1: Print a self-test report 
•Solution 2: Clear the print queue 
•Solution 3: Disconnect and reconnect the USB cable 
•Solution 4: Verify the driver configuration
•Solution 5: Check if the printer is paused or offline 
•Solution 6: Clear the print queue manually 
•Solution 7: Restart the print spooler
•Solution 8: Check the software application
Chapter 12 
158 Troubleshooting
Troubleshooting
 
						

							Solution 1: Print a self-test report 
Solution: Print a self-test report to see if the product can print and is communicating 
with the computer. 
To print a self-test report 
1. Load letter or A4 unused plain white paper into the input tray. 
2. Press and hold the Cancel button and then press the Start Copy Color button. 
The product prints a self-test report, which might indicate the source of the printing 
problem. A sample of the ink test area of the report is shown below.
3. Make sure the test patterns show a complete grid and the thick color lines are 
complete. 
• If more than a few lines in a pattern are broken, this might indicate a problem 
with the nozzles. You might need to clean the print cartridges. 
• If the black line is missing, faded, streaked, or shows lines, this might indicate 
a problem with the black print cartridge in the right slot. 
• If any of the color lines are missing, faded, streaked, or show lines, this might 
indicate a problem with the tri-color print cartridge in the left slot. 
If the self-test report fails to print, make  sure you set up the product properly. See the 
Start Here guide that came with the product for information about setting it up. 
Cause: The product was not set up properly. 
If this did not solve the issue, try the next solution.
Errors 159
Troubleshooting
 
						

							Solution 2: Clear the print queue 
Solution: Restart your computer to clear the print queue. 
To clear the print queue 
1. Restart your computer. 
2. After the computer has restarted, check the print queue. 
a . Depending upon your operating system, do one of the following: 
• Windows Vista: On the  Windows taskbar, click Start, click Control 
Panel , and then click Printers. 
• Windows XP: On the  Windows taskbar, click Start, click Control Panel, 
and then click  Printers and Faxes. 
• Windows 2000: On the Windows taskbar, click  Start, point to Settings, 
and then click  Printers. 
b . Double-click the icon for your product to open the print queue. 
If there are no print jobs pending, the issue might have been resolved. 
3. Try to print again. 
Cause: The computer needed to be restarted to clear the print queue. 
If this did not solve the issue, try the next solution.
Solution 3: Disconnect and reconnect the USB cable
Solution: Disconnect the USB cable from the computer and product, and then 
reconnect it. 
To disconnect and reconnect the USB cable 
1. Disconnect the USB cable from the product. 
2. Disconnect the USB cable from the computer. 
3. Leave the USB cable disconnected for 5-6 seconds. 
4. Reconnect the USB cable to the product and the computer.
Chapter 12 
160 Troubleshooting
Troubleshooting
 
						

							After reconnecting the USB cable, the product should start printing the jobs in 
queue.
NOTE: If you are connecting the product through a USB hub, make sure the 
hub is turned on. If the hub is on, try connecting directly to your computer.
5. If the product does not start printing automatically, start another print job. 
Cause: The USB cable needed to be disconnected. 
If this did not solve the issue, try the next solution.
Solution 4: Verify the driver configuration
Solution: Check to make sure the product is set as the default printer and it is using 
the correct printer driver. 
To verify that the product is  set as the default printer 
1. Depending upon your operating system, do one of the following: 
• W i n d o w s  V i s t a :  O n  t he Windows taskbar, click Start, click Control Panel, and 
then click  Printers. 
• Windows XP: On the Windows taskbar, click  Start, click Control Panel, and 
then click  Printers and Faxes. 
• Windows 2000: On the Windows taskbar, click  Start, point to Settings, and 
then click  Printers. 
2. Make sure the correct product is set as the default printer. 
The default printer has a check mark in a black circle next to it. 
3. If the wrong product is set as the default printer, right-click the correct product and 
select  Set as Default. 
To verify the print driver 
1. Depending upon your operating system, do one of the following: 
• W i n d o w s  V i s t a :  O n  t he Windows taskbar, click Start, click Control Panel, and 
then click  Printers. 
• Windows XP: On the Windows taskbar, click  Start, click Control Panel, and 
then click  Printers and Faxes. 
• Windows 2000: On the Windows taskbar, click  Start, point to Settings, and 
then click  Printers. 
2. Right-click the icon next to the product, and select Properties. 
3. Click the Ports tab to verify that the product is using the correct port. 
The port that the product is using is highlighted and has a check mark next to it. 
The product should be set to use a DOT4 or the USB00X (where X is replaced 
by a number) port. 
4. If the product is using the wrong port, click the correct port to select it. 
The port that the product is now using is highlighted and has a check mark next 
to it. 
5. Click the Advanced tab.
Errors 161
Troubleshooting
 
						

							6.Check the driver listed in the Driver drop-down menu to verify that the product is 
using the correct driver. 
The name of your product should be listed as the driver. 
7. If the wrong driver is selected, select the correct driver from the Driver drop-down 
menu. 
8. Click OK to save your changes. 
Cause: If there was more than one product configured on the same computer, the 
product in use was not be set as the default printer, or the wrong driver might have 
been configured. 
If this did not solve the issue, try the next solution.
Solution 5: Check if the printer is paused or offline 
Solution: Check to make sure the product is not paused or offline. 
To check if the printer is paused or offline 
1. Depending upon your operating system, do one of the following: 
• Windows Vista: On the  Windows taskbar, click Start, click Control Panel, and 
then click  Printers. 
• Windows XP: On the Windows taskbar, click  Start, click Control Panel, and 
then click  Printers and Faxes. 
• Windows 2000: On the Windows taskbar, click  Start, point to Settings, and 
then click  Printers 
2. Double-click the icon for your product to open the print queue. 
3. On the Printer menu, make sure there are no check marks next to Pause 
Printing  or Use Printer Offline. 
On the  Printer menu, make sure there are no check marks next to Pause 
Printing  or Use Printer Offline. If a check mark is present on either option, click 
the menu option to remove it. If the menu has the  Use Printer Online option, 
select that option to put  a check mark next to it. 
4. If you made any changes, try to print again. 
Cause: The product was paused or offline. 
If this did not solve the issue, try the next solution.
Chapter 12 
162 Troubleshooting
Troubleshooting
 
						

							Solution 6: Clear the print queue manually 
Solution: Manually clear the print queue. 
To clear the print queue manually 
1. Depending upon your operating system, do one of the following: 
• W i n d o w s  V i s t a :  O n  t he Windows taskbar, click Start, click Control Panel, and 
then click  Printers. 
• Windows XP: On the Windows taskbar, click  Start, click Control Panel, and 
then click  Printers and Faxes. 
• Windows 2000: On the Windows taskbar, click  Start, point to Settings, and 
then click  Printers. 
2. Double-click the icon for your product to open the print queue. 
3. On the Printer menu, click Cancel all documents or Purge Print Document, 
and then click  Yes to confirm. 
4. If there are still documents in the queue, restart the computer and try printing 
again after the computer has restarted. 
5. Check the print queue again to make sure it is clear, and then try to print again. 
If the print queue is not clear, or if it is cl ear but jobs are still failing to print, proceed 
to the next solution. 
Cause: The print queue needed to be manually cleared. 
If this did not solve the issue, try the next solution.
Solution 7: Restar t the print spooler 
Solution: Restart the print spooler. 
To stop and restart the print spooler 
1. On the Windows taskbar, click Start, and then click Control Panel. 
2. Double-click Administrative Tools, and then double-click Services. 
3. Scroll down the list and click Print Spooler, and then click Stop to stop the 
service. 
4. Click Start to restart the service, and then click OK. 
5. Restart the computer and try printing again after the computer has restarted. 
Cause: The print spooler needed to be restarted. 
If this did not solve the issue, try the next solution.
Errors 163
Troubleshooting
 
						

							Solution 8: Check the software application 
Solution: Verify whether the software application is the problem. 
To verify the software application 
1. Close the software application and reopen it. 
2. Try to print again from the software application.
NOTE:The printer might not support printing from a DOS application. 
Determine if the software application is Windows-based or DOS-based by 
checking the system requirem ents of the application.
3.Try printing from Notepad to see if the issue is the software application or the 
driver. 
To print fr om Notepad 
a . On the Windows taskbar, click Start, and then click Programs or All 
Programs . 
b . Click Accessories, and then click Notepad. 
c . Type a few characters of text into Notepad. 
d . Click File, and then click Print. 
4. If printing is successful from Notepad but not the software application, contact the 
manufacturer of that application for support. 
Cause: The software application was be failing or could not interface with the print 
driver incorrectly.
Product might not be  correctly installed 
Try the following solutions to resolve the issue. Solutions are listed in order, with the most 
likely solution first. If the first solution does not solve the problem, continue trying the
remaining solutions until the issue is resolved. 
•Solution 1: Reset the product 
•Solution 2: Check the power cord and USB cable
•Solution 3: Restart the computer 
•Solution 4: Uninstall and reinstall the product 
•Solution 5: Uninstall and reinstall the HP Photosmart Software 
Solution 1: Reset the product 
Solution: Turn off the product and reset it by disconnecting the power cord. Wait 
60 seconds, and then plug in the power cord. Turn on the product. 
Cause: You needed to reset the product. 
If this did not solve the issue, try the next solution.
Chapter 12 
164 Troubleshooting
Troubleshooting
 
						

							Solution 2: Check the power cord and USB cable 
Solution: Make sure that the power cord and USB cable are properly attached and 
plugged in. Also, make sure that the product is turned on. 
To check the power supply 
1. Make sure the power cord is firmly connected to both the product and the power 
adaptor. Plug the power cord into a power outlet, surge protector, or power strip.
1Power connection
2Power cord and adaptor
3Power outlet
2. Make sure the product is turned on. 
3. If the product is not receiving electrical power, connect it to another power outlet. 
4. Turn off the product and reset it by disconnecting the power cord. 
5. Wait 5 seconds, and plug in the power cord. 
6. Turn on the product. 
7. Try to scan again.
Errors 165
Troubleshooting
 
						

							To check the USB connection 
1. Verify that the USB cable is securely plugged into the USB port on the back of 
the product. 
2. Make sure the other end of the USB cable is plugged into a USB port on your 
computer.
3. Try to scan again. 
If the scan fails, continue to the next step. 
4. Do one of the following, depending upon how the product is connected to the 
computer: 
• If the USB cable is connected to a USB hub, try unplugging and replugging 
the USB cable into the hub. If that does not work, try turning off the hub and 
then turning it on again. Finally, try disconnecting the cable from the hub and 
connecting it directly to the computer. 
• If the USB cable is connected to a docking station for a laptop, disconnect the 
cable from the docking station and connect it directly to the computer. 
• If the USB cable is directly connected to the computer, try plugging it into 
another USB port on the computer. 
5. If there are other USB devices connected to the computer, disconnect the other 
devices, except for the  keyboard and the mouse. 
6. Check the USB cable to make sure it is functioning properly.
NOTE:If you are using an older cable, it might not be working properly. Try 
connecting it to another product to see if the USB cable works. If you
experience problems, the USB cable might need to be replaced. Also verify 
that the cable does not exceed 3 meters (9.8 feet) in length.
7. If another USB cable is available, try using that one instead. 
8. Restart the computer. 
9. After the computer restarts, try to scan again. 
Cause: The power cord or USB cable was not attached properly. 
If this did not solve the issue, try the next solution.
Chapter 12 
166 Troubleshooting
Troubleshooting
 
						

							Solution 3: Restart the computer 
Solution: Restart the computer. 
Cause: You might not have restarted the computer after installing the product 
software. Or, there might have been another problem with the computer. 
If this did not solve the issue, try the next solution.
Solution 4: Uninstall and reinstall the product 
Solution: Uninstall the product from the Printers and Faxes control panel and then 
reinstall it. 
To uninstall and reinstall the product 
1. Disconnect the USB cable between the product and the computer. 
2. On the Windows taskbar, click Start, Printers and Faxes. 
3. Right-click the product and select Delete. 
4. Wait several seconds, and then reconnect the product to the computer with the 
USB cable. 
5. Follow any onscreen prompts to reinstall the product. 
Cause: There might have been a problem when you originally installed the product. 
If this did not solve the issue, try the next solution.
Solution 5: Uninstall and reinstall the HP Photosmart Software 
Solution: Uninstall the complete HP Photosmart Software from the computer and 
then reinstall it using the CD that came with your product. 
To uninstall and reinstall the software 
1. On the Windows taskbar, click Start, Settings, Control Panel. 
2. Double-click Add/Remove Programs. 
3. Remove all the items that are related to the HP scanning software. 
A message appears on the computer to restart after removing some programs 
from the  Add/Remove Programs list. 
4. Select Click here to restart later. 
5. Disconnect the product from your computer and then restart your computer.
NOTE:It is important that you disconnect the product before restarting your 
computer. Do not connect the product to your computer until after you have 
reinstalled the software.
6. Insert the HP Photosmart CD-ROM into your computer’s CD-ROM drive and then 
start the Setup program.
NOTE: If the Setup program does not appear, locate the setup.exe file on 
the CD-ROM drive and double-click it.
Errors 167
Troubleshooting