Epson Xp 202 Manual

							Removing Jammed Paper from the Front Cover (A)
1. Open the front cover.
2. Remove the jammed paper.
cImportant:
Do not touch the parts inside the printer. Doing so may cause a malfunction.
3. Close the front cover.
Note:
If any torn pieces of paper remain, select Setup > Maintenance > Remove Paper after clearing the paper jam error.
This helps you to remove the remaining pieces of paper.
Removing Jammed Paper from the Rear Paper Feed (B1)
Remove the jammed paper.
User's Guide
Solving Problems
171 
						

							Removing Jammed Paper from the Front Paper Feed Slot (B2)
1. Remove the output tray and pull out the paper cassette.
2. Pull the lever.
The cover comes 
off.
3. Remove the jammed paper.
User's Guide
Solving Problems
172 
						

							4. Reattach the cover.
5. Insert the paper cassette, and then set the output tray.
Removing Jammed Paper from the Paper Cassette (C1/C2/C3/C4)
Note:
If the optional cabinet and the paper cassette units are installed, do not pull out two or more paper cassettes at the same
time.
1. Pull out the paper cassette.
User's Guide
Solving Problems
173 
						

							2. Remove the jammed paper.
3.
Insert the paper cassette.
Removing Jammed Paper from Rear Cover 1 (D1) and Rear Cover 2
(D2)
1. Open rear cover 1.
2. Remove the jammed paper.
User's Guide
Solving Problems
174 
						

							Note:
If you cannot remove the paper, pull rear cover 2 a little.
3. Pull out rear cover 2.
4.
Remove the jammed paper.
5. Insert rear cover 2.
6. Close rear cover 1. User's Guide
Solving Problems
175 
						

							Removing Jammed Paper from the Rear Cover (E)
1. Open the rear cover.
2. Remove the jammed paper.
3.
Close the rear cover.
Removing Jammed Paper from the ADF (F)
!Caution:
Be careful not to trap your hand or 
fingers when opening or closing the document cover. Otherwise you may be
injured.
User's Guide
Solving Problems
176 
						

							1. Raise the lever and open the ADF cover.
2. Remove the jammed paper.
3. Close the ADF cover. User's Guide
Solving Problems
177 
						

							4. Open the document cover.
5. Remove the jammed paper.
6.
Close the document cover. User's Guide
Solving Problems
178 
						

							7. Raise the ADF input tray, and then remove the jammed paper.
Paper Does Not Feed Correctly
Check the following if the paper jams, paper feeds at a slant, several sheets of paper feed at a time, no paper feeds,
or paper is ejected.
❏Place the printer on a flat surface and operate in the recommended environmental conditions.
❏Use paper supported by this printer.
❏Follow the paper handling precautions.
❏Load paper in the correct direction, and slide the edge guides against the edges of the paper.
❏Do not load more than the maximum number of sheets 
specified for the paper. For plain paper, do not load
above the line just under the 
d symbol inside the edge guide.
❏Insert the paper cassette all the way.
❏When paper does not feed after replacing the maintenance rollers, the rollers may not have been replaced
correctly. Check if they have been replaced correctly.
❏If you have added optional paper cassette units, you need to make settings in the printer driver.
❏When a no-paper error occurs although paper is loaded in the rear paper feed, load paper again in the center of
the rear paper feed.
❏When multiple sheets of paper feed at once during manual 2-sided printing, remove any paper which is loaded
in the paper source before you reload the paper.
❏Load and eject paper without printing to clean the paper path.
❏Close the ink case immediately if you opened it during printing. Keeping the ink case open during printing
pauses the print job.
❏Do not open the rear cover while printing. This causes a paper jam.
❏
The maintenance rollers may be at the end of their service life. Select Setup > Maintenance > Maintenance
Roller Information > Maintenance Roller Status, and then replace the maintenance rollers as necessary.
❏Make sure the paper size and paper type settings of the paper source are correct. User's Guide
Solving Problems
179 
						

							Related Information
&“Environmental Specifications” on page 203
&“Available Paper and Capacities” on page 42
&“Paper Handling Precautions” on page 42
&“Loading Paper in the Paper Cassette” on page 46
&“Loading Paper in the Rear Paper Feed” on page 48
&“Loading Paper in the Front Paper Feed Slot” on page 50
&“Replacing Maintenance Rollers in Paper Cassette 1” on page 130
&“Replacing Maintenance Rollers in Paper Cassette 2 to 4” on page 133
&“Setting the Optional Paper Cassette Unit in the Printer Driver” on page 228
&“Cleaning the Paper Path for Paper Feeding Problems” on page 145
&“Setting the Paper Size and Paper Type for Each Paper Source” on page 52
Original Does Not Feed in the ADF
❏Use originals supported by the ADF.
❏Load originals in the correct direction, and slide the ADF edge guides against the edges of the originals.
❏Clean the inside of the ADF.
❏Do not load above the line just under the 
d symbol inside the ADF edge guide.
❏Check that the ADF icon appears on the control panel. If it does not appear, place the originals again.
Related Information
&“Available Originals for the ADF” on page 54
&“Placing Originals on the ADF” on page 54
&“Cleaning the ADF” on page 146
Power and Control Panel Problems
Power Does Not Turn On
❏Hold down the P button for a little longer.
❏Make sure the power cord is securely plugged in.
Power Does Not Turn Off
Hold down the P button for a little longer. If you still cannot turn off the printer, unplug the power cord. To
prevent the print head from drying out, turn the printer back on and turn it 
off by pressing the 
P button.
LCD Screen Gets Dark
The printer is in sleep mode. Press any button on the control panel to return the LCD screen to its former state. User's Guide
Solving Problems
180