Dell 1800MP Projector Owners Manual

							Appendix: Regulatory Notices71
Appendix: Regulatory Notices
FCC Notices (U.S. Only)
Most Dell computer systems are classified by the Federal Communications Commission 
(FCC) as Class B digital devices. To determine which classification applies to your computer 
system, examine all FCC registration labels located on the bottom, side, or back panel of 
your computer, on card-mounting brackets, and on the cards themselves. If any one of the 
labels carries a Class A rating, your entire system is considered to be a Class A digital device. 
If all labels carry an FCC Class B rating as distinguished by either an FCC ID number or the 
FCC logo, ( ), your system is considered to be a Class B digital device.
Once you have determined your system’s FCC classification, read the appropriate FCC 
notice. Note that FCC regulations provide that changes or modifications not expressly 
approved by Dell could void your authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following 
two conditions:
• This device may not cause harmful interference.
• This device must accept any interference received, including interference that may 
cause undesired operation.
Class A
This equipment has been tested and found to comply with the limits for a Class A digital 
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference when the equipment is operated in a commercial 
environment. This equipment generates, uses, and can radiate radio frequency energy and, if 
not installed and used in accordance with the manufacturer’s instruction manual, may cause 
harmful interference with radio communications. Operation of this equipment in a 
residential area is likely to cause harmful interference, in which case you will be required to 
correct the interference at your own expense.
Class B
This equipment has been tested and found to comply with the limits for a Class B digital 
device pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable 
protection against harmful interference in a residential installation. This equipment 
generates, uses, and can radiate radio frequency energy and, if not installed and used in 
accordance with the manufacturer’s instruction manual, may cause interference with radio 
communications. However, there is no guarantee that interference will not occur in a 
particular installation. If this equipment does cause harmful interference to radio or 
television reception, which can be determined by turning the equipment off and on, you are 
encouraged to try to correct the interference by one or more of the following measures: 
						

							72Appendix: Regulatory Notices
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the 
receiver is connected.
• Consult the dealer or an experienced radio/television technician for help.
FCC Identification Information
The following information is provided on the device or devices covered in this document in 
compliance with FCC regulations: 
• Product name: DLP Projector
• Model number: 1800MP/DELL
• Company name: 
Dell Inc.
One Dell Way
Round Rock, Texas 78682 USA
512-338-4400
NOM Information (Mexico Only)
The following information is provided on the device(s) described in this document in 
compliance with the requirements of the official Mexican standards (NOM):
Exporter: Dell Inc.
One Dell Way
Round Rock, TX 78682
Importer: Dell Computer de México, S.A. de C.V. 
Paseo de la Reforma 2620 - 11° Piso 
Col. Lomas Altas 
11950 México, D.F. 
Ship to: Dell Computer de México, S.A. de C.V. 
al Cuidado de Kuehne & Nagel de México S. de R.L.
Avenida Soles No. 55
Col. Peñon de los Baños
15520 México, D.F.
Model Supply Voltage Frequency Current Consumption
1800MP AC 100-240 V 50-60 Hz 2.3 A 
						

							Glossary73
Glossary
ANSI LUMENS —A standard for measuring light output, used for comparing 
projectors.
A
SPECT RATIO —The most popular aspect ratio is 4:3 (4 by 3). Early television and 
computer video formats are in a 4:3 aspect ratio, which means that the width of 
the image is 4/3 times the height.
B
ACKLIT (BACKLIGHT) —Refers to a remote control, or a projector control panel, that 
has buttons and controls that are illuminated. 
Bandwidth— The number of cycles per second (Hertz) expressing the difference 
between the lower and upper limiting frequencies of a frequency band; also, the 
width of a band of frequencies.
Brightness— The amount of light emitting from a display or projection display or 
projection device. The brightness of projector is measured by ANSI lumens.
Color Temperature— A method of measuring the whiteness of a light source. 
Metal halide lamps have a higher temperature compared to halogen or 
incandescent lights.
Component Video—A method of delivering quality video in a format that 
contains all the components of the original image. These components are referred 
to as luma and chroma and are defined as YPbPr for analog component and 
YCbCr for digital component. Component video is available on DVD players and 
projectors.
Composite Video — The combined picture signal, including vertical and 
horizontal blanking and synchronizing signals.
Compression— A function that deletes resolution lines from the image to fit in 
the display area.
Compressed SVGA— To project an 800x600 image to a VGA projector, the 
original 800x600 signal must be compressed down. The data displays all the 
information with only two thirds of the pixels (307,000 vs 480,000). The resulting 
image is SVGA page size but sacrifices some of the image quality. If you are using 
an SVGA computers, connecting VGA to a VGA projector. provide better results.
Compressed SXGA— Found on XGA projectors, compressed SXGA handling 
allows these projectors to handle up to 1280x1024 SXGA resolution. 
Compressed XGA— Found on SVGA projectors, compressed XGA handling 
allows these projectors to handle 1024x768 XGA resolution. 
						

							74Glossary
Contrast Ratio— Range of light and dark values in a picture, or the ratio between 
their maximum and minimum values. There are two methods used by the 
projection industry to measure the ratio:
1Full  On/Off — measures the ratio of the light output of an all white image (full 
on) and the light output of an all black (full off) image. 
2ANSI — measures a pattern of 16 alternating black and white rectangles. The 
average light output from the white rectangles is divided by the average light 
output of the black rectangles to determine the 
ANSI contrast ratio. 
Full On/Off contrast is always a larger number than ANSI contrast for the same 
projector.
dB— decibel—A unit used to express relative difference in power or intensity, 
usually between two acoustic or electric signals, equal to ten times the common 
logarithm of the ratio of the two levels. 
Diagonal Screen— A method of measuring the size of a screen or a projected 
image. It measures from one corner to the opposite corner. A 9FT high, 12FT 
wide, screen has a diagonal of 15FT. This document assumes that the diagonal 
dimensions are for the traditional 4:3 ratio of a computer image as per the example 
above. 
DLP— Digital Light Processing—Reflective display technology developed by 
Texas Instruments, using small manipulated mirrors. Light passes through a color 
filter is sent to the DLP mirrors which arrange the RGB colors into a picture 
projected onto screen, also known as DMD.
DMD— digital Micro- Mirror Device— Each DMD consists of thousands of 
tilting, microscopic aluminum alloy mirrors mounted on a hidden yoke.  
DVI— Digital Visual Interface— Defines the digital interface between digital 
devices such as projectors and personal computers. For devices that support DVI, a 
digital to digital connection can be made that eliminates the conversion to analog 
and thereby delivers an unblemished image. 
Focal Length— The distance from the surface of a lens to its focal point.
Frequency— It is the rate of repetition in cycles per seconds of electrical signals. 
Measured in Hz. 
Hz — Frequency of an alternating signal. See Frequency. 
Keystone Correction— Device that will correct an image of the distortion 
(usually a wide-top narrow-bottom effect) of a projected image caused by 
improper projector to screen angle.
Laser Pointer— A small pen or cigar sized pointer that contains a small battery 
powered laser, which can project a small, red (typically), high intensity beam of 
light that is immediately very visible on the screen. 
						

							Glossary75
Maximum Distance— The distance from a screen the projector can be to cast an 
image that is useable (bright enough) in a fully darkened room. 
Maximum Image Size— The largest image a projector can throw in a darkened 
room. This is usually limited by focal range of the optics. 
Metal Halide Lamp— The type of lamp used in many medium and all high end 
portable projectors. These lamps typically have a half-life of 1000-2000 hours. 
That is they slowly lose intensity (brightness) as they are used, and at the half-life 
point, they are half as bright as when new. These lamps output a very hot 
temperature light, similar to mercury vapor lamps used in streetlights.. Their 
whites are extremely white (with slight bluish cast.) and make Halogen lamps 
whites look very yellowish by comparison.
Minimum Distance— The closest position that a projector can focus an image 
onto a screen.
NTSC— The United States broadcast standard for video and broadcasting.
PAL— A European and international broadcast standard for video and 
broadcasting. Higher resolution than NTSC.
Power Zoom— A zoom lens with the zoom in and out controlled by a motor, 
usually adjusted from the projectors control panel and also the remote control.
Reverse Image— Feature that allows you to flip the image horizontally. When 
used in a normal forward projection environment text, graphics, etc, are 
backwards. Reverse image is used for rear projection.
RGB— Red, Green, Blue— typically used to describe a monitor that requires 
separate signals for each of the three colors.
S-Video—A video transmission standard that uses a 4-pin mini-DIN connector to 
send video information on two signal wires called luminance (brightness, Y) and 
chrominance (color, C). S-Video is also referred to as Y/C.
SECAM— A French and international broadcast standard for video and 
broadcasting. Higher resolution than NTSC.
SVGA— Super Video Graphics Array— 800 x 600 pixels count.
SXGA— Super Ultra Graphics Array,—1280 x 1024 pixels count.
UXGA— Ultra Extended Graphics Array—1600 x 1200 pixels count.
VGA— Video Graphics Array—640 x 480 pixels count.
XGA— Extra Video Graphics Array— 1024 x 768 pixels count. 
						

							76Glossary
Zoom Lens— Lens with a variable focal length that allows operator to move the 
view in or out making the image smaller or larger. 
Zoom Lens Ratio— Is the ratio between the smallest and largest image a lens can 
projector from a fixed distance. For example, a 1.4:1 zoom lens ratio means that a 
10 foot image without zoom would be a 14 foot image with full zoom.  
						

							FILE LOCATION:  C:\Documents and Settings\Mikan\Ƈ¦±\Coretronic\1800MP\SRC\IX.fm
DELL CONFIDENTIAL – PRELIMINARY 9/12/06
FOR PROOF ONLY
Index77
Index
A
Adjusting Projection Image Size 16
Adjusting the Projected Image
 14
Lowering the Projector Height
 
14
Elevator button
 14
Elevator foot
 14
Tilt adjustment wheel
 14
Raising the Projector Height
 14
Adjusting the Projector Zoom and 
Focus
 15
Focus ring
 15
Zoom tab
 15
C
Changing the Lamp 35
Connecting a Computer with a 
RS232 cable
 12
Connecting the Projector
Composite video cable
 10
Connecting to a computer
 8
Connecting with a Component 
Cable
 11
Connecting with a Composite 
Cable
 10
Connecting with an S-video Ca-
ble
 9
VGA to YPbPr cable
 11
Power cord
 8, 9, 10, 11, 12RS232 cable
 12
S-video cable
 9
USB cable
 8
VGA to VGA cable
 8
Connection Ports
Audio input connector
 7
Audio output connector
 7
Kensington lock hole
 7
RS232 connector
 7
S-video connector
 7
USB remote connector
 7
VGA-A In connector
 7
VGA-A out connector
 7
VGA-B In connector
 7
Video input connector
 7
Contact Dell
 5, 18, 33, 34, 35
Control Panel
 17
D
Dell
Contacting
 43
M
Main Unit 6
Elevator button
 6
Focus ring
 6
Lens
 6
Power cord connector
 6 
						

							78Index
Remote control receiver 6
Zoom tab
 6
O
On-Screen Display 20
Auto-Adjust
 21
DISPLAY (in PC Mode)
 24
DISPLAY (in Video Mode)
 25
Input Select
 21
LAMP
 25
LANGUAGE
 26
Main Menu
 21
PICTURE (in PC Mode)
 23
PICTURE (in Video Mode)
 23
Preferences
 27
Set Up
 22
P
Powering On/Off the Projector
Powering Off the Projector
 13
Powering On the Projector
 13
R
Remote Control 19
S
Specifications
Audio
 38
Brightness
 37
Color Wheel Speed
 37Compatibility Modes
 40
Contrast Ratio
 37
Dimensions
 38
Displayable Color
 37
Environmental
 38
H. Frequency
 37
I/O Connectors
 38
Lamp
 37
Light Valve
 37
Noise Level
 38
Number of Pixels
 37
Power Consumption
 37
Power Supply
 37
Projection Distance
 37
Projection Lens
 37
Projection Screen Size
 37
Regulatory
 38
RS232 Protocol
 39
Uniformity
 37
V. Frequency
 37
Video Compatibility
 37
Weight
 38
Support
Contacting Dell
 43
T
Troubleshooting 31
Contact Dell
 31 
						

							www.dell.com | support.dell.com
Projecteur Dell™ 1800MP
Manuel de lutilisateur 
						

							Remarques, Notices, et 
Avertissements
 REMARQUE : Une REMARQUE indique une information 
importante qui vous permettra de mieux utiliser votre projecteur.
 
REMARQUE : Une NOTICE indique soit une détérioration 
potentielle du matériel ou une perte de données et vous indique 
comment éviter le problème.
 
ATTENTION : Un AVERTISSEMENT indique des risques 
potentiels de détérioration de propriétés, de blessures 
corporelles ou de mort.
____________________
Les informations contenues dans ce document peuvent être modifiées sans 
avertissement préalable.
© 2006 Dell Inc. Tous droits réservés.
Toute reproduction sans la permission écrite de Dell Inc. est strictement interdite.
Les marques utilisées dans ce texte : Dell , le logo DELL, Dimension, OptiPlex, 
Dell Precision, Latitude, Inspiron, DellNet, PowerApp, PowerEdge, 
PowerConnect et PowerVault sont des marques commerciales de Dell Inc. ; 
DLP
® et le logo DLP sont des marques déposées de Texas Instruments ; 
Microsoft et Windows sont des marques déposées de Microsoft Corporation ; 
Macintosh est une marque déposée dApple Computer, Inc.
D’autres marques et appellations commerciales peuvent être utilisées dans le 
présent document pour désigner soit les entités revendiquant les marques et les 
noms, soit leurs produits. Dell Inc. rejette tout intérêt de propriété dans les 
marques et noms autres que les siens.
Restrictions et limites de responsabilité
Les informations contenues dans ce document, y compris toutes les 
instructions, les précautions, et les règlements dapprobation et de certification, 
sont basés sur les déclarations fournies à Dell par le fabricant et nont pas été 
indépendamment vérifiés ou testés par Dell. Dell rejette toute responsabilité 
concernant les anomalies pouvant apparaître dans ces informations.
Toutes les déclarations et revendications concernant les propriétés, capacités, 
vitesses ou qualifications des parties référencées dans ce document sont faites 
par le fournisseur et non par Dell. Dell démentit avoir la connaissance de 
lexactitude, perfection ou la vérification de telles déclarations.
Modèle 1800MP
Septembre 2006 Rev. A00