Home > Comdial > Communications System > Comdial Digital Telephone System Instructions Manual

Comdial Digital Telephone System Instructions Manual

    Download as PDF Print this page Share this page

    Have a look at the manual Comdial Digital Telephone System Instructions Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 133 Comdial manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.

    							InstallationIMl66-107Power Failure Station Connections
    The system provides a tip and ring pair connected to
    line 1 as an emergency power failure circuit. This
    circuit is active during a commercial AC power failure if
    an external battery assembly is not installed to provide
    battery back-up power to the system. Connect an
    industry standard, single-line telephone, such as a
    model 2500, to a power failure pair.and use it toprovide communications capability until the 
    AC power
    to the system is restored.
    The power 
    failure.pair is located as follows and as
    detailed in 
    Figure 3-7 below.
    NOTE: The system also provides one power failure
    connection with each add-on expansion
    module.POWER FAILURE TERMINALS ON
    STATION CONNECTOR BLOCK
    I4-LINE, 8-STATION AND 8-LINE, I6-STATION BASE UNITS1TYPICAL INDUSTRY STANDARD
    NON-ELECTRIC TELEPHONE
    (POWER FAILURE INTERFACE1
    --
    GfPJ/
    gj--1-w34--l--
    35--l--
    36--l--
    37--i--
    36
    --1--39--l--
    40--l--
    41----c-
    42--t--
    43---I--
    44--I--
    45--l--
    46--l--
    47--I--
    46--I--
    49--l--
    SO--l--
    CLIP TERMINALS
    -OR-
    POWER FAILURE JACKlI6-LINE, 32-STATION BASE UN111
    Figure 3-7. Power Failure Connection
    3-22 
    						
    							IMl66-107
    Installation
    Auxiliary Equipment Interface
    You can connect an industry-standard telephone or
    data device on a line ahead of the common equipment
    if you wish.If you do so, the system can detect an
    off-hook condition in the connected device and turn on
    the line status light at the system telephones to
    indicate that the line is busy. 
    Table 3-1 (on page 7)
    and 
    Figure 3-8 below detail the auxiliary interface
    connections.
    NOTE: When you are employing this auxiliary
    interface feature, the line-to-line port
    reassignment as discussed previously and in
    Chapter 4 works as described except in regard
    to line 2 and line 4.Line 2 can only be
    reassigned to line port 4 and line 4 can only be
    reassigned to line port 2
    0 Connection is across tip and ring of lines 2 and 4.
    The system provides the auxiliary interface
    connections at terminals 
    1 and 6 of common
    equipment line jacks 1 and 2.
    Figure 3-8. Auxiliary Interface Connections 
    						
    							installationIM166-107Common Audible And
    Auxiliary Ringing Interface
    You can use he relay closure dry-contact points for
    controlling external audible equipment. These contact
    closures track the pattern of the ringing for incoming
    calls. The contacts are closed during the ringing
    period and are open during the silent period.
    A typical common audible connection is illustrated
    on 
    Figure 3-9 .
    piifq
    Do not exceed a 1 amp at 24 volts (0.5 amp
    at 48 volts) load on these control terminals.
    If the load requirements exceed this limit,
    connect the load through an external slave
    relay. DO NOT CONNECT THESE
    CONTROL TERMINALS DIRECTLY TO THE
    117VAC LINE.
    Outside Lines
    0 Common audible terminals provide a dry-contact
    closure whenever any of the outside lines that you
    have connected to the common equipment ring 
    with
    an incoming call.
    Selected Ports
    0 Station 7 7 audible terminals provide a dry-contact
    relay closure whenever ringing is sent to station 17
    or to a programmable destination. Use class of
    service programming to choose either station 
    17 or
    the paging port as the ringing destination. Refer to
    Chapter 4 for details.
    When you have programmed for station port 
    17
    ringing, it is a common practice to use a
    customer-supplied external device to provide loud
    ringing and connected in a manner similar to the
    common audible arrangement shown in 
    Figure 3-9.
    1CAUTION 1
    Do not connect a external paging amplifier
    or any external ringing device to the
    station port 17 connections.
    0 When you have programmed forpaging port
    tinging, it is a common practice to use a
    customer-supplied external paging amplifier
    connected to the paring port to amplify and
    broadcast the ringing tones sent to, the paging port
    by the system . You can employ the relay closures
    that appear at the ringing terminals to energize the
    external paging amplifier during the periods when
    the ringing tones are being sent if necessary.
    NOTE: Refer to the following paragraph headed
    m for a discussion of
    external paging amplifier connections and
    infotma tion for using the paging port ringing
    tem?ina/s in an alternate paging eriable
    function.
    3-24 
    						
    							IM166-107Installation
    (Wiring shown for low current application - see caution text)
    Power
    Source for
    - AGorY,.....a+ .-,J”
    Signallingl-0
    IllpuL as
    bvimRequiredw-.,1-I
    (Wiring shown with slave relay connection for high current application - see caution text)Wire to 
    o
    EE:
    - Power
    24V Q lAMax.%tF for
    4 ACorDC
    48V 0.5A Max.Input as
    Interface
    -II- RelayRequired
    Relay
    VcltaKmta;ng Diode
    Slave
    RelayPower
    Syrc~ for4 ACorDC
    ;;wtwInput asRequired
    ,
    Station Connector Block
    (4-Line, b-station and
    E-Line, 1 E-Station Base Units)
    cAJsw7
    Station 17 Audible
    Common Audible
    Barrier Strip
    (lbline, 32Station Base Unit)
    Figure 3-9. Typical Common Audible Interface Wiring3-25 
    						
    							InstallationExternal Paging Interface
    The system provides a special transformer-isolated
    paging port that you can use to couple the system to a
    customer-supplied external paging amplifier. This
    external paging port does not provide a talk-back path
    nor will it recognize DTMF dial tones.
    You can use the relay closure dry-contact points that
    the system makes available at the ringing port terminal
    for controlling the external paging amplifier during a
    paging operation. These contacts close 
    and stay
    closed during the time that a paging operation is active
    to provide a constant enable signal path for the paging
    amplifier.
    IMl66-107NOTE: This paging enable constant closure function
    overrides the ring pattern closure provided
    when ringing is sent to the paging port.See
    the previous paragraph titled 
    -on Au&&
    0 Connect the audio input of a customer-supplied
    external paging amplifier to the paging port as
    shown below in 
    Figure 3-10.
    0 If the paging amplifier requires an enable signal,
    connect the enable leads to the station 17 audible
    terminals as shown in 
    Figure 3-10.PA SYSTEM
    coyI) EOUlPYllTOil@& l6-sTAfloN 8UEIJMIT mom,
    46-+-
    +,-+-----w-46 -+- --B--M.
    t:-=r-- -
    alp 7mw1~~6TO RINGING PORT
    /TERMINALS IF ENABLE IS
    REOU IRE 
    0.STATION 
    17 AUDIBLE
    BARRIER STR IP
    l16-LINE. 32-STATION BASE UNIT1STATION CONNECTOR BLOCK
    I4-LINE. 8-STATION AND 8-LINE. IG-STATION BASE UNITS1
    Figure 3-10. Typical External Paging Connection3-26 
    						
    							IM166-107External Paging Interface 
    - Line Port
    You can use class of service programming to convert
    a line port to be an AUXILIARY port. As an
    AUXILIARY port, a user can use it to couple a
    telephone to an external paging device that you have
    wired to the line port. He or she does this from any
    station with that line presence by pressing the proper
    line button to select the AUXILIARY port. The user
    can 
    dial DTMF tones or dial pulses through the
    AUXILIARY port as needed. The paging enable relayInstallation
    closure feature discussed previously is not available
    for use with this installation.
    0 Connect the audio input of a customer-supplied
    external paging amplifier to the tip and ring leads of
    the AUXILIARY port as shown in 
    Figure 3-l 1 below.
    0 You can install a DTMF tone select, zone-paging
    amplifier if you wish.If do you install this type of
    amplifier, the user must dial the zone-select code
    after he or she presses the AUXILIARY port line
    select button.
    Program line port as Program line port as
    auxiliary port and connectauxiliary port and connect
    PA system to tip and ring
    PA system to tip and ring
    that port.
    PA SystemRING 3
    w ! TIP3LTIP 4
    LINETERMINATION‘TYPE 
    66MXX CONNECTOR BLOCKOR‘INDIVIDUAL 6-POSITIONMDDULAR JACKS________I______-____----------------CM01
    Figure 3-11. Typical External Paging Connection - Line Port
    ii3-27 
    						
    							InstallationIMl66-107Data Device Connections
    The system provides two RS232 Data Ports for use.
    0 When you use a video display terminal (VDT) to
    perform class of service programming, connect it to
    RS232 Data Port A.
    0 When you use a serial data printer for SMDR,
    SMDA, and COS printout, connect it to the RS232
    Data Port B.
    0 When you use a Caller ID Interface (product code
    CID08) to identify incoming calls, connect it to
    RS232 Data Port B using the special cable provided
    with the CID08. Refer to the paragraph titled 
    C&r
    Identification Service Support (located on page
    4-40) for installation details associated with this
    feature.
    The distance between a data device and the common
    equipment can be up to 500 feet in a quiet electrical
    environment. Some sites may require shielded cable
    for long runs. For longer distances, you must install
    limited distance modems to relay the data
    communications between the common equipment and
    a data device.
    When preparing a cable for connection to a data
    device, refer to the manufacturer’s manual for the
    equipment being interfaced and make the following
    wiring connections:
    0 Wire the common equipment RD (data from device
    to common equipment) connection to the device TD
    (transmit data) connection.
    0 Wire the common equipment TD (data to device
    from common equipment) connection to the device
    RD (receive data) connection.
    0 Wire the common equipment SG (signal ground)
    connection to the device SG (signal ground)
    connection.
    0 If required for proper operation, wire the common
    equipment CTS (clear-to-send status from device to
    common equipment) connection to the device RTS
    (request-to-send) connection.
    NOTE: The common equipment requires a positive
    voltage, with respect to signal ground, in order
    to send data.
    The default data communications format is as follows:
    0 7-bit data with 2 stop bits and no parity
    0 Baud rate of 300 baud
    Configure a data device to match Jhis format for initial
    operation or reprogram the system’s data format to
    match those of a data device.
    The system’s data ports are located as follows and are
    connected as illustrated in 
    Figure 3-12 on the next
    we.
    rbLine, &Station And &Line, 164tation Base Units
    lClip terminals 37 - 40 (dataport A) and 41 -44
    (data port B) on station connector block.
    SuLPoRTPORT RTD = TERMINAL 37
    TERMINAL 41RD = TERMINAL 38
    TERMINAL 42CTS 
    = TERMINAL 39TERMINAL 43SG = TERMINAL 40TERMINAL 44
    l&Line, 32-Station Base Unit
    0 Special modular jacks are available as data ports
    SIGJACKNone1
    CTS
    2
    RD
    3
    TD4
    SG5
    None6 
    						
    							4
    c
    IiF’
    TO RS232
    DATA PORT ATYPICAL 
    VDTINTERFACE
    INOUSTRY STANDARDUOOULAR LINE CORDI4-CONDUCTOR)INDUSTRY STANDARD
    MODULAR LINE CORD
    I4-CONWCTOR)
    TYPICN UOUJLAR TO EIA ADAPTERWIRlN6 SHOWN FOR REFERENCE ONLY.
    TYPEN 
    MODULAR TO EIA ADAPT6RWlRlN6 SHOWN FOR REFERENCE ONLY.MODULAR JACK DATA PORTS
    ll6-LINE. 32-STATION BASE UNITI
    Figure 3-i2. Typical Data Device ConnectionsRS232
    DATA PORT 
    0
    hifzii65431 I
    RS232DATA PORT A
    IFRONT VIEW OF J&KS1
    = NO CONNECTION: =CTS3 -RD4 = Tb5 = so6 : NO CONNECTION
    ST~NJI CormcmR aocK DATA KRTS
    %B-STATICN BAB LNIT Ml8-LIIGSTATICN M INIT)
    NOTES :I. MAXIMUM DISTANCE BETWEEN COMMON EQUIPMENT
    CABINET AND PRINTER OR VDT TYPICALLY LIMITED
    TO 500 FEET. LONGER DISTANCES 
    REWIRE LIMITED
    DISTANCE MODEMS AT EITHER END OF RUN.
    2. SOME DATA 
    OEVICES REQUIRE CTS SIGNAL FORVROPER OPERATION. ROUTE TO DEVICE AS NEECED. 
    						
    							InstallationIMl66-107Music Interfaceimpedance of this input is approximately 500 ohms.
    If music is to be part of the system, connect aUse the volume control on the music source to adjust
    customer-provided music source to the commonthe audio level of the music as required.
    equipment music interface jack (phono jack) provided
    for this purpose as shown below in Figure 3-13. The
    MUSIC INTERFACE
    MUSIC SOURCE
    (FOR MUSIC ON
    HOLD AND BACKGROUND
    MUS IC 1
    Figure 3-13. Music Interface 
    						
    							IMl66-107InstallationAdd-On Expansion Module
    Introduction
    You can install one or two optional add-on expansion
    modules on the common equipment base unit to
    increase the line and station capacity of an installed
    system. The add-on module is as follows:
    0 408 Expansion Module - A four-line by eight-station
    expansion unit
    The expansion capabilities provided by the add-on
    module are shown in 
    Figure 3-14 on the next page.
    The default numbering of the expanded lines and
    stations begin with the next higher line or station 
    port
    number from that provided by the host base unit. The
    numbering continues sequentially from top module to
    bottom module if two modules are installed. For
    example: The defaulted 
    8-line, 16-station base unitprovides station ports 10 through 25 and lines 1
    through 8. When installed, a 408 Expansion module
    will provide station ports 26 through 33 and lines 9
    through 12 thus creating a twelve line by twenty-four
    station system.
    Each expansion module provides a tip and ring pair as
    an emergency power failure circuit. This circuit is
    connected to the first module-provided line.
    The line connections of the expansion module are
    available at two modular jacks. When facing the jack
    openings, lines 1 and 2 are provided by the jack on the
    right and lines 3 and 4 are provided by the jack on the
    left. Line connections are detailed in 
    Table 3-5,
    below.
    The station connections are available at a 
    50-pin
    connector. 
    Table 3-6 detail these station connections.
    Table 3-5. Line Connections - 408 Expansion Module
    Add-On Expansion Module - continued on next page . . .
    3-31 
    						
    All Comdial manuals Comments (0)

    Related Manuals for Comdial Digital Telephone System Instructions Manual