Cisco 6509 E Installation Manual
Have a look at the manual Cisco 6509 E Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 53 Cisco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
1-25 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 1 Catalyst 6500 Series Switch Chassis Overview Catalyst 6509 Switch Supervisor enginesSupports Supervisor Engine 2, Supervisor Engine 32, Supervisor Engine 32 PISA, Supervisor Engine 720, and Supervisor Engine 720-10GE. –Supervisor Engine 2 is installed in slot 1 and slot 2. –Supervisor Engine 32, Supervisor Engine 32 PISA, Supervisor Engine 720, and Supervisor Engine 720-10GE are installed in slot 5 and slot 6. –Supervisor Engine 32, Supervisor Engine 32 PISA, Supervisor Engine 720, and Supervisor Engine 720-10GE require that the high-speed fan tray be installed in the chassis. You must also install a 2500 W or higher capacity power supply in the chassis to power the high-speed fan tray. NoteThe 2500 W power supply, when supporting the high-speed fan tray, can be powered from either 120 VAC or 220 VAC. –Supervisor Engine 720 and Supervisor Engine 720-10GE have built-in switching fabric. Switch Fabric Modules (WS-C6500-SFM and WS-X6500-SFM2) are not supported by Supervisor Engine 720 and Supervisor Engine 720-10GE and cannot be installed in the same chassis. –Supervisor Engine 32 and Supervisor Engine 32 PISA do not support the Switch Fabric Modules (WS-C6500-SFM and WS-X6500-SFM2). The uplink ports are fully functional on all redundant supervisor engine models when they are in standby mode. NoteIn systems with redundant supervisor engines, both supervisor engines must be the same model and have the same daughter card configurations. Each supervisor engine must have the resources to run the switch on its own, which means all supervisor engine resources are duplicated. Identical supervisor engine memory configurations are recommended, but are not required as long as the supervisor engine with the smaller memory configuration is sufficient to run the configured features of the switch. Additionally, each supervisor engine must have its own flash device and console port connections. Table 1-11 Catalyst 6509 Switch Features (continued) Feature Description
1-26 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 1 Catalyst 6500 Series Switch Chassis Overview Catalyst 6509 Switch ModulesChassis supports up to eight Catalyst 6500 series modules. WS-C6500-SFM and WS-X6500-SFM2 Switch Fabric Modules must be installed in slot 5 or slot 6. Some Catalyst 6500 series modules: –Are not supported –Require that you install a Supervisor Engine 720 –Have chassis slot restrictions –Require a specific software release level Check your software release notes for specific information on supported modules. Table 1-11 Catalyst 6509 Switch Features (continued) Feature Description
1-27 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 1 Catalyst 6500 Series Switch Chassis Overview Catalyst 6509 Switch Table 1-12 Catalyst 6509 Switch Specifications Item Specification Environmental Temperature, operating Certified for operation: 32° to 104°F (0° to 40°C) Designed and tested for operation: 32° to 130°F (0° to 55°C) NoteThe Catalyst 6500 series switches are equipped with internal air temperature sensors that are triggered at 104°F (40°C) generating a minor alarm and at 131°F (55°C) generating a major alarm. Temperature, ambient nonoperating and storage–20° to 65°C (–4° to 149°F) Thermal transition 0.5°C per minute (hot to cold) 0.33°C per minute (cold to hot) Humidity (RH), ambient (noncondensing) operating 10% to 90% Humidity (RH), ambient (noncondensing) nonoperating and storage 5% to 95% Altitude, operating Certified for operation: 0 to 6500 feet (0 to 2000 m) Designed and tested for operation: –200 to 10,000 feet (–60 to 3000 m) Physical Characteristics Dimensions (H x W x D)25.2 x 17.2 x 18.4 in. (64.0 x 43.7 x 46.7 cm). Chassis depth including cable guide is 21.64 in. (55.0 cm). Chassis requires 15 RU. Chassis can be mounted in equipment racks that meet ANSI/EIA 310-D and ETS 300-119 standards. Weight Chassis only: 55 lb (24.9 kg). Chassis fully configured with 1 supervisor engine, 8 switching modules, and 2 power supplies: 194.5 lb (88.2 kg). Airflow WS-C6K-9SLOT-FAN (Standard fan tray)—340 CFM WS-C6K-9SLOT-FAN2 (Optional high-speed fan tray)—630 CFM NoteTo maintain proper air circulation through the Catalyst switch chassis, we recommend that you maintain a minimum 6-inch (15 cm) separation between a wall and the chassis air intake or a wall and the chassis air exhaust. You should also allow a minimum separation of 12 inches (30.5 cm) between the hot air exhaust on one chassis and the air intake on another chassis. Failure to maintain adequate air space can cause the chassis to overheat and the system to fail. On Catalyst chassis in which the airflow is from front to back, the chassis may be placed side-by-side.
1-28 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 1 Catalyst 6500 Series Switch Chassis Overview Catalyst 6509-E Switch Catalyst 6509-E Switch The Catalyst 6509-E switch is an enhanced version of the Catalyst 6509 chassis. Figure 1-10 shows a front view of the chassis. Table 1-13 provides a description of the major switch features. Table 1-14 lists the specifications of the Catalyst 6509-E switch chassis. Figure 1-10 Catalyst 6509-E Switch 113676 FA N STA TUS INPUT OKFA N OKOUTPUT FA I L o INPUT OKFA N OKOUTPUT FA I L o 1 2 3 4 5 6 7 8 9 Power supply 2 (redundant)Power supply 1 ESD ground strap connector 8 PORT GIGABIT ETHER NET WS-X64081LINKSTATUS2 3 4 5 6 7 8LIN KLINKLIN KLINKLINKLINKLINK 8 PORT GIGABIT ETHER NET WS-X64081LIN KSTATUS2 3 4 5 6 7 8LINKLINKLINKLINKLINKLINKLINK 8 PORT GIGABIT ETHER NET WS-X64081LINKSTATUS2 3 4 5 6 7 8LIN KLINKLINKLIN KL INKLINKLINK 8 PORT GIGABIT ETHERNET WS-X64081L INKSTATUS2 3 4 5 6 7 8LINKLIN KLIN KLINKLINKLIN KLINK 8 P OR T G IG ABIT E THE R N ET W S -X 6 4 0 81LINKS T AT U S2 34 56 7 8LINKLINKLINKLINKLINKLINKLINK 24 PORT 1 00FX WS- X6224STATUS 2 4 P O R T 1 0 0 F X W S -X 6 2 2 4S T AT U S 1LINK2LINK3LINK4LINK5LINK6LINK7LINK8LINK9LINK10LINK11LINK12LINK13LINK14LINK15LINK16LINK17LINK18LINK19LINK20LINK21LINK22LINK23LINK24LINK 1LINK2LINK3LINK4LINK5LINK6LINK7LINK8LINK9LINK1 0LINK1 1LINK1 2LINK1 3LINK1 4LINK1 5LINK1 6LINK1 7LINK1 8LINK1 9LINK2 0LINK2 1LINK2 2LINK2 3LINK2 4LINK WS-SUP32-G E-3BSTA TUS SYSTEM ACTIVE PWR MGMT RESETCATALYST 6500 SUPERVIS OR ENGINE 32CONSOLE EJECTDISK 0PORT 1 PORT 2 PORT 3 PORT 4PORT 5 PORT 6 PORT 7PORT 8PORT 9 USB 2.0 LINK LINK LINK LINK LINK LINK LINK LINK LINKWS-SUP32-G E-3BSTA TUS SYSTEM ACTIVE PWR MGMT RESETCATALYST 6500 SUPERVIS OR ENGINE 32 CONSOLE EJECTDISK 0PORT 1 PORT 2 PORT 3 PORT 4PORT 5 PORT 6 PORT 7PORT 8PORT 9 USB 2.0 LINK LINK LINK LINK LINK LINK LINK LINK LINK Switching modules Switching modules Fan assembly Supervisor engine Redundant supervisor engine
1-29 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 1 Catalyst 6500 Series Switch Chassis Overview Catalyst 6509-E Switch Table 1-13 Catalyst 6509-E Switch Features Feature Description Chassis Nine horizontal slots. Slots are numbered from (1) top to (9) bottom. Power supplies Supports one or two power supplies. The following power supplies are supported: –WS-CAC-2500W (2500 W AC-input power supply) –WS-CDC-2500W (2500 W DC-input power supply) –WS-CAC-3000W (3000 W AC-input power supply) –WS-CAC-4000W-US (4000 W AC-input power supply) –WS-CAC-4000W-INT (4000 W AC-input power supply) –PWR-4000-DC (4000 W DC-input power supply) –WS-CAC-6000W (6000 W AC-input power supply) –WS-CAC-8700W-E (8700 W AC-input power supply) NoteFor information and specifications for each of the supported power supplies, refer to Appendix A, “Power Supply Specifications,” in the Catalyst 6500 Series Switches Installation Guide. Installed power supplies can be of different wattage ratings. Installed power supplies can also be both AC-input, both DC-input, or one AC-input and one DC-input. Power supplies can be configured in either redundant or nonredundant mode. Supervisor Engine 2T requires a 3000 W or greater power supply to operate. All Catalyst 6500 series AC-input power supplies require single-phase source AC. Source AC can be out of phase between multiple power supplies or multiple AC-power plugs on the same power supply because all AC power supply inputs are isolated.
1-30 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 1 Catalyst 6500 Series Switch Chassis Overview Catalyst 6509-E Switch Supervisor enginesSupports Supervisor Engine 2, Supervisor Engine 32, Supervisor Engine 32 PISA, Supervisor Engine 720, Supervisor Engine 720-10GE, and Supervisor Engine 2T. –Supervisor Engine 2 is installed in slot 1 and slot 2. –Supervisor Engine 32, Supervisor Engine 32 PISA, Supervisor Engine 720, Supervisor Engine 720-10GE, and Supervisor Engine 2T are installed in slot 5 and slot 6. –Supervisor Engine 720, Supervisor Engine 720-10GE, and Supervisor Engine 2T have built-in switching fabric; Switch Fabric Modules (WS-C6500-SFM and WS-X6500-SFM2) are not supported. –Supervisor Engine 32 and Supervisor Engine 32 PISA do not support the Switch Fabric Modules (WS-C6500-SFM and WS-X6500-SFM2). The uplink ports are fully functional on all redundant supervisor engine models when they are in standby mode. NoteIn systems with redundant supervisor engines, both supervisor engines must be the same model and have the same daughter card configurations. Each supervisor engine must have the resources to run the switch on its own, which means all supervisor engine resources are duplicated. Identical supervisor engine memory configurations are recommended, but are not required as long as the supervisor engine with the smaller memory configuration is sufficient to run the configured features of the switch. Additionally, each supervisor engine must have its own flash device and console port connections. Modules Chassis supports up to eight Catalyst 6500 series modules. WS-C6500-SFM and WS-X6500-SFM2 Switch Fabric Modules must be installed in slot 5 or slot 6. Some Catalyst 6500 series modules: –Are not supported –Require that you install a Supervisor Engine 720 or Supervisor Engine 2T –Have chassis slot restrictions –Require a specific software release level NoteCheck your software release notes for specific information on module support and restrictions. Table 1-13 Catalyst 6509-E Switch Features (continued) Feature Description
1-31 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 1 Catalyst 6500 Series Switch Chassis Overview Catalyst 6509-E Switch Table 1-14 Catalyst 6509-E Switch Specifications Item Specification Environmental Temperature, operating Certified for operation: 32° to 104°F (0° to 40°C) Designed and tested for operation: 32° to 130°F (0° to 55°C) NoteThe Catalyst 6500 series switches are equipped with internal air temperature sensors that are triggered at 104°F (40°C) generating a minor alarm and at 131°F (55°C) generating a major alarm. Temperature, nonoperating and storage–4° to 149°F (–20° to 65°C) Thermal transition 0.5°C per minute (hot to cold) 0.33°C per minute (cold to hot) Humidity (RH), ambient (noncondensing) operating 10% to 90% Humidity (RH), ambient (noncondensing) nonoperating and storage 5% to 95% Altitude, operating Certified for operation: 0 to 6500 feet (0 to 2000 m) Designed and tested for operation: –200 to 10,000 feet (–60 to 3000 m) Physical Characteristics Dimensions (H x W x D)24.5 x 17.5 x 18.2 in. (62.2 x 44.5 x 46.0 cm). Chassis depth including cable guide is 21.64 in. (55.0 cm). Chassis requires 15 RU. Chassis can be mounted in equipment racks that meet ANSI/EIA 310-D and ETS 300-119 standards. Weight Chassis only: 55 lb (24.9 kg). Chassis fully configured with 1 supervisor engine, 8 switching modules, and 2 power supplies: 135 lb (61.2 kg). AirflowWS-C6509-E-FAN—846 CFM NoteTo maintain proper air circulation through the Catalyst switch chassis, we recommend that you maintain a minimum 6-inch (15 cm) separation between a wall and the chassis air intake or a wall and the chassis air exhaust. You should also allow a minimum separation of 12 inches (30.5 cm) between the hot air exhaust on one chassis and the air intake on another chassis. Failure to maintain adequate air space can cause the chassis to overheat and the system to fail. On Catalyst chassis in which the airflow is from front to back, the chassis may be placed side-by-side.
1-32 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 1 Catalyst 6500 Series Switch Chassis Overview Catalyst 6509-NEB Switch Catalyst 6509-NEB Switch The Catalyst 6509-NEB switch is a 9-slot vertical chassis. Figure 1-11 shows a front view of the chassis. Table 1-15 provides a description of the major switch features. Table 1-16 lists the specifications of the Catalyst 6509-NEB switch chassis. Figure 1-11 Catalyst 6509-NEB Switch INPUT OKFA N OKOUTPUT FA I L o INPUT OKFA N OKOUTPUT FA I L o FA N STATUS 30695 8 PORT GIGABIT ETHER NETWS-X6408 1LINKSTA TUS 2 3 45 6 7 8LINK LINK LINK LINK LINK LINK LINK 8 PORT GIGABIT ETHER NETWS-X6408 1LINKSTA TUS 2 3 45 6 7 8LINK LINK LINK LINK LINK LINK LINK 8 PORT GIGABIT ETHER NETWS-X6408 1LINKSTATUS 2 3 45 6 7 8LINK LINK LINK LINK LINK LINK LINK 8 PORT GIGABIT ETHER NETWS-X6408 1LINKSTATUS 2 3 45 6 7 8LINK LINK LINK LINK LINK LINK LINK 24 PORT 100FXWS-X6224STA TUS1LIN K2LIN K3LINK4LINK5LIN K6LIN K7LINK8LIN K9LINK1 0LINK1 1LIN K1 2L IN K1 3LINK1 4LINK1 5LIN K1 6LIN K1 7LIN K1 8LIN K1 9LINK2 0LIN K2 1L IN K2 2LINK2 3LIN K2 4LINK Slots 1-9 (right to left) Power supply 1Power supply 2 (redundant) ESD ground strap connection W S -S U P32 -GE -3 BSTATUS SYST EM ACT IVE PWR MG MT RES ETC A T A L YS T 6 500 S U P E RV IS O R E N G IN E 32 C O N S O L E E J EC TD IS K 0P O R T 1 P O R T 2 P O R T 3 P O R T 4P O R T 5 P O R T 6 P O R T 7P O R T 8P O R T 9 U S B 2 .0 LIN K LINK LINK LINK LINK LINK LINK LIN K LINK W S -S U P32 -G E -3 BSTA TUS SYST EM ACT IVE PWR MG MT RES ETC A T A L YS T 6 500 SU P E RV IS O R E N G IN E 32 C O N S O L E E J EC TD IS K 0P O R T 1 P O R T 2 P O R T 3 P O R T 4P O R T 5 P O R T 6 P O R T 7P O R T 8P O R T 9 U S B 2 .0 LIN K LIN K LIN K LINK LINK LINK LINK LINK LINK 8 PORT GIGABIT ETHER NETWS-X6408 1LINKSTA TUS 2 3 45 6 7 8LINK LINK LINK LINK LINK LINK LINK 24 PORT 100FXWS-X6224STATUS1LIN K2LIN K3LINK4LI NK5L INK6LIN K7L INK8LINK9LIN K1 0LIN K1 1LINK1 2LINK1 3LIN K1 4LIN K1 5LINK1 6LINK1 7L IN K1 8LINK1 9LINK2 0LIN K2 1LINK2 2LINK2 3LINK2 4LIN K Switching modules Fan assembly Supervisor engine Redundant supervisor engine
1-33 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 1 Catalyst 6500 Series Switch Chassis Overview Catalyst 6509-NEB Switch Table 1-15 Catalyst 6509-NEB Switch Features Feature Features Chassis Nine vertical slots. Slots are numbered from 1 (right) to 9 (left). Power supplies Supports one or two power supplies. The following power supplies are supported: –WS-CAC-2500W (2500 W AC-input power supply) –WS-CDC-2500W (2500 W DC-input power supply) –WS-CAC-3000W (3000 W AC-input power supply) –WS-CAC-4000W-US (4000 W AC-input power supply) –WS-CAC-4000W-INT (4000 W AC-input power supply) –PWR-4000-DC (4000 W DC-input power supply) –WS-CAC-6000W (6000 W AC-input power supply) –WS-CAC-8700W-E (8700 W AC-input power supply) NoteThe 6000 W and the 8700 W AC-input power supplies are limited to 4500 W maximum output when installed in the Catalyst 6509-NEB chassis. NoteFor information and specifications for each of the supported power supplies, refer to Appendix A, “Power Supply Specifications,” in the Catalyst 6500 Series Switches Installation Guide. Installed power supplies can be of different wattage ratings. Installed power supplies can also be both AC-input, both DC-input, or one AC-input and one DC-input. Power supplies can be configured in either redundant or nonredundant mode. All Catalyst 6500 series AC-input power supplies require single-phase source AC. Source AC can be out of phase between multiple power supplies or multiple AC-power plugs on the same power supply because all AC power supply inputs are isolated. Single power supplies are installed in the left power supply bay. The second power supply is installed in the right power supply bay.
1-34 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 1 Catalyst 6500 Series Switch Chassis Overview Catalyst 6509-NEB Switch Supervisor enginesSupports Supervisor Engine 2, Supervisor Engine 32, Supervisor Engine 32 PISA, Supervisor Engine 720, and Supervisor Engine 720-10GE. –Supervisor Engine 2 is installed in slot 1 or slot 2. –Supervisor Engine 32 is installed in slot 5 or slot 6. Supervisor Engine 32, Supervisor Engine 32 PISA, Supervisor Engine 720, and Supervisor Engine 720-10GE are supported if the WS-6509-NEB-UPGRD kit is installed. –Supervisor Engine 32, Supervisor Engine 32 PISA, Supervisor Engine 720, and Supervisor Engine 720-10GE. are installed in slot 5 or slot 6. –Supervisor Engine 720 and Supervisor Engine 720-10GE have built-in switching fabric. Switch Fabric Modules (WS-C6500-SFM and WS-X6500-SFM2) are not supported by Supervisor Engine 720 and cannot be installed in the same chassis. –Supervisor Engine 32 and Supervisor Engine 32 PISA do not support the Switch Fabric Modules ((WS-C6500-SFM and WS-X6500-SFM2). The uplink ports are fully functional on all redundant supervisor engine models when they are in standby mode. NoteIn systems with redundant supervisor engines, both supervisor engines must be the same model and have the same daughter card configurations. Each supervisor engine must have the resources to run the switch on its own, which means all supervisor engine resources are duplicated. Identical supervisor engine memory configurations are recommended, but are not required as long as the supervisor engine with the smaller memory configuration is sufficient to run the configured features of the switch. Additionally, each supervisor engine must have its own flash device and console port connections. Modules Chassis supports up to eight Catalyst 6500 series modules. WS-C6500-SFM and WS-X6500-SFM2 Switch Fabric Modules must be installed in slot 5 or slot 6. Some Catalyst 6500 series modules: –Are not supported –Require that you install a Supervisor Engine 720 –Have chassis slot restrictions –Require a specific software release level NoteCheck your software release notes for specific information on module support and restrictions. Table 1-15 Catalyst 6509-NEB Switch Features (continued) Feature Features