Cisco 6509 E Installation Manual

							C-1
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-04
APPENDIXC
ESD Precautions
Revised: July 2011
This appendix provides information on preventing ESD when removing and installing modules in a 
chassis.
Attaching Your ESD Grounding Strap
Electrostatic discharge (ESD) damage, which can occur when modules or other FRUs are improperly 
handled, results in intermittent or complete failures. Modules consist of printed circuit boards that are 
fixed in metal carriers. Electromagnetic interference (EMI) shielding and connectors are integral 
components of the carrier. Although the metal carrier helps to protect the board from ESD, always use 
an ESD grounding strap when handling modules.
For preventing ESD damage, follow these guidelines:
Always use an ESD wrist strap and ensure that it makes maximum contact with bare skin. ESD 
grounding straps are available with banana plugs, metal spring clips, or alligator clips. All 
Catalyst 6500 series chassis are equipped with a banana plug connector (identified by the ground 
symbol next to the connector) somewhere on the front panel. 
 –If you have an older Catalyst  6500 series chassis equipped with a plastic banana plug connector, 
we recommend that you use either the supplied ESD grounding wrist strap (with a metal clip) 
or an ESD grounding wrist strap equipped with an alligator clip. 
 –If you have a newer Catalyst 6500 series chassis that has a bare metal hole as the banana plug 
connector (also identified by the ground symbol next to the hole), we recommend that you use 
a personal ESD grounding strap equipped with a banana plug. 
If you choose to use the disposable ESD wrist strap supplied with most FRUs or an ESD wrist strap 
equipped with an alligator clip, you must attach the system ground lug to the chassis in order to 
provide a proper grounding point for the ESD wrist strap.
NoteThis system ground is also referred to as the network equipment building system (NEBS) 
ground.
If your chassis does not have the NEBS system ground attached, you must install the system ground 
lug and a ground wire. Refer to the online Catalyst 6500 Series Switches Installation Guide for the 
procedure. 
						

							C-2
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-04
Appendix C      ESD Precautions
  Attaching Your ESD Grounding Strap
After you install the system ground lug, follow these steps to correctly attach the ESD wrist strap:
Step 1Attach the ESD wrist strap to bare skin as follows:
a.If you are using the ESD wrist strap supplied with the FRUs, open the wrist strap package and 
unwrap the ESD wrist strap. Place the black conductive loop over your wrist and tighten the strap 
so that it makes good contact with your bare skin.
b.If you are using an ESD wrist strap equipped with an alligator clip, open the package and remove 
the ESD wrist strap. Locate the end of the wrist strap that attaches to your body and secure it to your 
bare skin.
Step 2Grasp the spring or alligator clip on the ESD wrist strap and momentarily touch the clip to a bare metal 
spot (unpainted surface) on the rack. 
We recommend that you touch the clip to an unpainted rack rail so that any built-up static charge is then 
safely dissipated to the entire rack.
Step 3Attach either the spring clip or the alligator clip to the ground lug screw as follows (See Figure C-1):
a.If you are using the ESD wrist strap that is supplied with the FRUs, squeeze the spring clip jaws 
open, position the spring clip to one side of the system ground lug screw head, and slide the spring 
clip over the lug screw head so that the spring clip jaws close behind the lug screw head.
NoteThe spring clip jaws do not open wide enough to fit directly over the head of the lug screw 
or the lug barrel.
b.If you are using an ESD wrist strap that is equipped with an alligator clip, attach the alligator clip 
directly over the head of the system ground lug screw or to the system ground lug barrel. 
						

							C-3
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-04
Appendix C      ESD Precautions
  Attaching Your ESD Grounding Strap
Figure C-1 Attaching the ESD Wrist Strap Clip to the System Ground Lug Screw
In addition, follow these guidelines when handling modules:
Handle carriers by available handles or edges only; avoid touching the printed circuit boards or 
connectors.
Place a removed component board-side-up on an antistatic surface or in a static-shielding container. 
If you plan to return the component to the factory, immediately place it in a static-shielding 
container.
Never attempt to remove the printed circuit board from the metal carrier.
CautionFor safety, periodically check the resistance value of the antistatic strap. The measurement should be 
between 1 and 10 megohm (Mohm).
SUPERVISOR2 WS-X6K-SUP2-2GESTATUSSYSTEMCONSOLEPWR MGMTRESETC
O
N
S
O
LEC
ON
SO
LE
PO
R
T
M
O
DEP
C
M
C
IA EJE
CTP
O
R
T
 1PO
R
T 2S
w
itch
    Loa
d   
100%
1
%
LINK
LINKO
S
M
-4
O
C
1
2
 P
O
S
-S
I
4
 P
O
R
T
 O
C
-1
2
 P
O
S
 S
M
 IRS
T
A
T
U
S
1
1 2
23
3 4
4R
E
S
E
T L
I
N
K
L
IN
KL
I
N
K
L
I
N
K
C
A
R
R
I
E
R
A
L
A
R
M
C
A
R
R
I
E
R
A
L
A
R
M
C
A
R
R
I
E
R
A
L
A
R
M
C
A
R
R
I
E
R
A
L
A
R
M A
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
 
1 R
X
A
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
 
2 R
XA
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
 3 R
XA
C
T
IV
E
T
X
R
X
T
X
P
O
R
T
4 R
X
O
S
M
-
4
O
C
1
2
 P
O
S
-S
I
4
 P
O
R
T
 O
C
-1
2
 P
O
S
 S
M
 IR
S
T
A
T
U
S
1
1 2
23
3 4
4R
E
S
E
T L
I
N
K
L
I
N
KL
I
N
K
L
I
N
K
C
A
R
R
I
E
R
A
L
A
R
M
C
A
R
R
I
E
R
A
L
A
R
M
C
A
R
R
I
E
R
A
L
A
R
M
C
A
R
R
I
E
R
A
L
A
R
M A
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
 
1 R
X
A
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
 
2 R
XA
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
 3 R
XA
C
T
I
V
E
T
X
R
X
T
X
P
O
R
T
4 R
X
144607
System ground
connector Grounding lug
Side view of
grounding lug
ESD ground
strap
Slide clip
behind screw
Clip installed
behind screwClip
Screw 
						

							C-4
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-04
Appendix C      ESD Precautions
  Attaching Your ESD Grounding Strap 
						

							IN-1
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-04
INDEX
Numerics
10/100 and 10/100/1000BASE modules
WS-X6148A-GE-TX     2-14 to 2-19
WS-X6148E-GE-45AT     2-29 to 2-31
WS-X6148-GE-TX     2-14 to 2-19
WS-X6148-RJ21     2-19 to 2-22
WS-X6148-RJ-45     2-23 to 2-28
WS-X6148X2-RJ-45     2-32 to 2-36
WS-X6196-RJ-21     2-37 to 2-40
WS-X6348-RJ21V     2-41 to 2-43
WS-X6348-RJ45     2-43 to 2-46
WS-X6516-GE-TX     2-47 to 2-49
WS-X6548-GE-TX     2-50 to 2-53
WS-X6548-RJ-21     2-54 to 2-57
WS-X6548-RJ-45     2-57 to 2-60
WS-X6748-GE-TX     2-61 to 2-66
WS-X6848-TX-2T/-2TXL     2-61 to 2-66
100-MB SFP transceivers     B-1 to B-3
10 and 10/100 fiber-based modules
See WS-X6024-10FL-MT
See WS-X6148-FE-SFP
See WS-X6324-100FX-MM
See WS-X6324-100FX-SM
See WS-X6524-100FX-MM
10-GB modules
WS-X6704-10GE     2-93 to 2-97
WS-X6708-10G-3C     2-98 to 2-101
WS-X6708-10G-3CXL     2-98 to 2-101
WS-X6716-10G-3C     2-102 to 2-108
WS-X6716-10G-3CXL     2-102 to 2-108
WS-X6716-10T-3C     2-108 to 2-114
WS-X6716-10T-3CXL     2-108 to 2-114
WS-X6816-10G-2T/-2TXL     2-102 to 2-108
WS-X6816-10T-2T/-2TXL     2-108 to 2-114
WS-X6908-10G     2-114 to 2-117
10-GB transceivers     B-8 to B-15
X2 transceivers     B-8 to B-15
modules supported on     B-8
optical transmit and receive specifications     B-15
physical and environmental specifications 
table
     B-15
XENPAK transceivers     B-8 to B-11
modules supported on     B-8
physical form (figure)     B-9
polish face types supported     B-9
specifications and cabling distances table     B-10
1-GB modules
WS-X6408A-GBIC     2-67 to 2-69
WS-X6416-GBIC     2-70 to 2-72
WS-X6516A-GBIC     2-73 to 2-77
WS-X6516-GBIC     2-73 to 2-77
WS-X6724-SFP     2-78 to 2-83
WS-X6748-SFP     2-83 to 2-89
WS-X6816-GBIC     2-89 to 2-92
WS-X6824-SFP-2T/-2TXL     2-78 to 2-83
WS-X6848-SFP-2T/-2TXL     2-83 to 2-89
1-GB transceivers
See either GBIC transceivers or SFP transceivers
40-GB modules
WS-X6904-40G     2-118 to 2-122
A
attenuators, using with 1000BASE-ZX GBIC     B-5
audience, document     1-v 
						

							Index
IN-2
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-04
B
blank module carriers     3-6
C
Catalyst 6503-E switches
airflow     1-9
altitude, operating     1-9
chassis, dimensions     1-9
environmental specifications     1-9
fantrays supported     1-9
features table     1-6
form factor, front view (figure)     1-6
form factor, rear view (figure)     1-6
humidity, operating     1-9
physical characteristics     1-9
slot numbering     1-7
specifications table     1-6
supervisor engines supported     1-8
temperature, operating     1-9
weight     1-9
Catalyst 6503 switches
airflow     1-5
altitude, operating     1-5
chassis, dimensions     1-5
environmental specifications     1-5
fan trays supported     1-5
features table     1-2
form factor, front view (figure)     1-2
form factor, rear view (figure)     1-2
humidity, operating     1-5
physical characteristics     1-5
slot numbering     1-3
specifications table     1-2
supervisor engines supported     1-4
temperature, operating     1-5
weight     1-5
Catalyst 6504-E switches
airflow     1-13
altitude, operating     1-13
chassis, dimensions     1-13
environmental specifications     1-13
fan trays supported     1-13
features table     1-10
form factor, front view (figure)     1-10
form factor, rear view (figure)     1-10
humidity, operating     1-13
physical characteristics     1-13
slot numbering     1-11
specifications table     1-10
supervisor engines supported     1-12
temperature, operating     1-13
weight     1-13
Catalyst 6506-E switches
airflow     1-22
altitude, operating     1-22
chassis dimensions     1-22
environmental specifications     1-22
fan trays supported     1-22
features table     1-19
form factor (figure)     1-19
humidity, operating     1-22
physical characteristics     1-22
slot numbering     1-20
specifications table     1-19
supervisor engines     1-21
temperature, operating     1-22
weight     1-22
Catalyst 6506 switches
airflow     1-18
altitude, operating     1-17
chassis, dimensions     1-18
environmental specifications     1-17
fan trays supported     1-18
features table     1-14
form factor (figure)     1-14
humidity, operating     1-17 
						

							Index
IN-3
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-04
physical characteristics     1-18
slot numbering     1-15
specifications     1-14
supervisor engines supported     1-16
temperature, operating     1-17
weight     1-18
Catalyst 6509-E switches
airflow     1-31
altitude, operating     1-31
chassis dimensions     1-31
environmental specifications     1-31
fan trays supported     1-31
features table     1-28
form factor (figure)     1-28
humidity, operating     1-31
physical characteristics     1-31
slot numbering     1-29
specifications table     1-28
supervisor engines     1-30
temperature, operating     1-31
weight     1-31
Catalyst 6509-NEB-A switches
airflow     1-39
altitude, operating     1-39
chassis dimensions     1-39
environmental specifications     1-39
fan trays supported     1-39
features table     1-36
form factor (figure)     1-36
humidity, operating     1-39
physical characteristics     1-39
specifications table     1-36
supervisor engines supported     1-38
temperature, operating     1-39
weight     1-39
Catalyst 6509-NEB switches
airflow     1-35
altitude, operating     1-35
chassis dimensions     1-35
environmental specifications     1-35
fan trays supported     1-35
features table     1-32
form factor (figure)     1-32
humidity, operating     1-35
physical characteristics     1-35
slot numbering     1-33
specifications     1-32
supervisor engines supported     1-34
temperature, operating     1-35
weight     1-35
Catalyst 6509 switches
airflow     1-27
altitude, operating     1-27
chassis, dimensions     1-27
environmental specifications     1-27
fan trays supported     1-27
features table     1-23
form factor (figure)     1-23
humidity, operating     1-27
physical characteristics     1-27
slot numbering     1-24
specifications table     1-23
supervisor engines supported     1-25
temperature, operating     1-27
weight     1-27
Catalyst 6509-V-E switches
airflow     1-43
altitude, operating     1-43
chassis dimensions     1-43
environmental specifications     1-43
fan trays supported     1-43
features table     1-40
form factor (figure)     1-40
humidity, operating     1-43
physical characteristics     1-43
specifications table     1-40
supervisor engines supported     1-42
temperature, operating     1-43 
						

							Index
IN-4
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-04
weight     1-43
Catalyst 6513-E switches
airflow     1-53
altitude, operating     1-52
chassis dimensions     1-53
environmental specifications     1-52
fan trays supported     1-53
features table     1-49
form factor (figure)     1-49
humidity, operating     1-52
physical characteristics     1-53
slot numbering     1-50
specifications table     1-49
supervisor engines supported     1-51
temperature, operating     1-52
weight     1-53
Catalyst 6513 switches
airflow     1-48
altitude, operating     1-48
chassis dimensions     1-48
environmental specifications     1-48
fan trays supported     1-48
features table     1-44
form factor (figure)     1-44
humidity, operating     1-48
physical characteristics     1-48
slot numbering     1-45
specifications table     1-44
supervisor engines supported     1-46
temperature, operating     1-48
weight     1-48
chassis
Catalyst 6509-E switches     1-31
commands
show module     3-16
show port     3-16
connectivity
checking     3-17
conventions, documentation     1-vi
CWDM GBIC transceivers
description     B-17
modules supported on     B-17
physical form (figure)     B-19
wavelength table     B-19
CWDM SFP transceivers
description     B-18
modules supported on     B-18
physical form (figure)     B-21
product numbers and color codes     B-21
D
dimensions, chassis
Catalyst 6503-E switches     1-9
Catalyst 6503 switches     1-5
Catalyst 6504-E switches     1-13
Catalyst 6506-E switches     1-22
Catalyst 6506 switches
     1-18
Catalyst 6509-NEB-A switches     1-39
Catalyst 6509-NEB switches     1-35
Catalyst 6509 switches     1-27
Catalyst 6509-V-E switches     1-43
Catalyst 6513-E switches     1-53
Catalyst 6513 switches     1-48
documentation
audience     1-v
conventions     1-vi
organization     1-v
related     1-xiii
DWDM GBIC transceivers
description     B-17
modules supported on     B-17
physical form (figure)     B-19
product numbers and ITU channel numbers     B-20
DWDM XENPAK transceivers
description     B-18
modules supported on     B-18 
						

							Index
IN-5
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-04
physical form (figure)     B-23
product numbers and ITU channel numbers     B-21
E
environmental specifications
Catalyst 6503-E switches     1-9
Catalyst 6503 switches     1-5
Catalyst 6504-E switches     1-13
Catalyst 6506-E switches     1-22
Catalyst 6506 switches     1-17
Catalyst 6509-E switches     1-31
Catalyst 6509-NEB-A switches     1-39
Catalyst 6509-NEB switches     1-35
Catalyst 6509 switches     1-27
Catalyst 6509-V-E switches     1-43
Catalyst 6513-E switches     1-52
Catalyst 6513 switches     1-48
environmental specifications tables
WS-X6516-GE-TX     2-49
WS-X6548-GE-TX     2-53
F
features tables
WS-X6024-10FL-MT     2-2
WS-X6148A-GE-TX     2-15
WS-X6148E-GE-45AT     2-29
WS-X6148-FE-SFP     2-4
WS-X6148-GE-TX     2-15
WS-X6148-RJ21     2-19
WS-X6148-RJ-45     2-24
WS-X6148X2-RJ-45     2-33
WS-X6196-RJ-21     2-37
WS-X6324-100FX-MM     2-7
WS-X6324-100FX-SM     2-7
WS-X6348-RJ21V     2-41
WS-X6348-RJ45     2-44
WS-X6408A-GBIC     2-67
WS-X6416-GBIC     2-70
WS-X6516A-GBIC     2-73
WS-X6516-GBIC     2-73
WS-X6516-GE-TX     2-47
WS-X6524-100FX-MM     2-10
WS-X6548-GE-TX     2-50
WS-X6548-RJ-21     2-54
WS-X6548-RJ-45     2-57
WS-X6704-10GE     2-93
WS-X6708-10G-3C     2-98
WS-X6708-10G-3CXL     2-98
WS-X6716-10G-3C     2-102
WS-X6716-10G-3CXL     2-102
WS-X6716-10T-3C     2-109
WS-X6716-10T-3CXL     2-109
WS-X6724-SFP     2-78
WS-X6748-GE-TX     2-61
WS-X6748-SFP     2-83
WS-X6816-10G-2T/-2TXL     2-102
WS-X6816-10T-2T/-2TXL     2-109
WS-X6816-GBIC     2-89
WS-X6824-SFP-2T/-2TXL     2-78
WS-X6848-SFP-2T/-2TXL     2-83
WS-X6848-TX-2T/-2TXL     2-61
WS-X6904-40G     2-119
WS-X6908-10G     2-114
fiber modules
WS-X6024-10FL-MT     2-2 to 2-4
WS-X6148-FE-SFP     2-4 to 2-7
WS-X6324-100FX-MM     2-7 to 2-9
WS-X6324-100FX-SM     2-7 to 2-9
WS-X6524-100FX-MM     2-10 to 2-13
filler plate, module     3-6
G
GBIC transceivers     B-3 to B-8
attenuators     B-5 
						

							Index
IN-6
Catalyst 6500 Series Ethernet Modules Installation Guide
OL-6265-04
cabling specifications (table)     B-4
modules supported on     B-3
optical GBICs physical form (figure)     B-4
WS-G5483 copper GBICs physical form (figure)     B-4
M
modules
blank module carriers     3-6
O
organization, document     1-v
P
physical and enviromental specifications tables
transceivers
1-GB SFP transceivers     B-8
physical and environmental specifications tables
fiber modules
WS-X6024-10FL-MT     2-4
transceivers
100-MB SFP transceivers     B-3
GBIC transceivers     B-6
X2 transceivers     B-15
WS-X6148A-GE-TX     2-17
WS-X6148E-GE-45AT     2-31
WS-X6148-FE-SFP     2-6
WS-X6148-GE-TX     2-17
WS-X6148-RJ21     2-22
WS-X6148-RJ-45     2-27
WS-X6148X2-RJ-45     2-36
WS-X6196-RJ-21     2-40
WS-X6324-100FX-MM     2-9
WS-X6324-100FX-SM     2-9
WS-X6348-RJ21V     2-43
WS-X6348-RJ45     2-46
WS-X6408A-GBIC     2-69
WS-X6416-GBIC     2-72
WS-X6516A-GBIC     2-75
WS-X6516-GBIC     2-75
WS-X6524-100FX-MM
     2-12
WS-X6548-RJ-21     2-56
WS-X6548-RJ-45     2-59
WS-X6704-10GE     2-96
WS-X6708-10G-3C     2-101
WS-X6708-10G-3CXL     2-101
WS-X6716-10G-3C     2-107
WS-X6716-10G-3CXL     2-107
WS-X6716-10T-3C     2-112
WS-X6716-10T-3CXL     2-112
WS-X6724-SFP     2-81
WS-X6748-GE-TX     2-64
WS-X6748-SFP     2-87
WS-X6816-10G-2T/-2TXL     2-107
WS-X6816-10T-2T/-2TXL     2-112
WS-X6816-GBIC     2-92
WS-X6824-SFP-2T/-2TXL     2-81
WS-X6848-SFP-2T/-2TXL     2-87
WS-X6848-TX-2T/-2TXL     2-64
WS-X6904-40G     2-121
WS-X6908-10G     2-116
physical characteristics
Catalyst 6503-E switches     1-9
Catalyst 6503 switches     1-5
Catalyst 6504-E switches     1-13
Catalyst 6506-E switches     1-22
Catalyst 6506 switches     1-18
Catalyst 6509-E switches     1-31
Catalyst 6509-NEB-A switches     1-39
Catalyst 6509-NEB switches     1-35
Catalyst 6509 switches     1-27
Catalyst 6509-V-E switches     1-43
Catalyst 6513-E switches     1-53
Catalyst 6513 switches     1-48