Cisco 6509 E Installation Manual
Have a look at the manual Cisco 6509 E Installation Manual online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 53 Cisco manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
2-111 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 2 Ethernet Switching Modules 10-Gigabit Ethernet Modules Chassis/slot restrictionsNot supported in the Catalyst 6503 chassis or the Catalyst 6509-NEB chassis Supported only in slots 9–13 in the Catalyst 6513 chassis and does not power up in slots 1–8. When the WS-X6716-10T module is installed in a Catalyst 6500-E series chassis or a Catalyst 6509-NEB-A chassis, the configuration is NEBS 3 compliant (chassis supports operating temperatures up to 55°C). When the WS-X6716-10T module is installed in a Catalyst 6500 non-E series chassis that is equipped with a fan tray 2 and a 2500 W or larger power supply, the configuration is not NEBS 3 compliant (chassis supports operating temperatures up to 40°C only). Support in the Catalyst 6509-NEB-A chassis requires two FAN-MOD-09 fan trays be installed. The WS-X6816-10T-2T/-2TXL Ethernet module is only supported on the Catalyst 6500 E-series switches equipped with Supervisor Engine 2T. Requires that modules be installed in adjacent slots or, if either adjacent slot is unused, you must install a switching-module filler plate (Cisco part numbers WS-X6K-SLOT-CVR-E or SLOTBLANK-09) rather than a blank slot cover (WS-X6K-SLOT-CVR) to maintain an adequate air flow through the chassis. Fabric connection Dual switch-fabric connections: –Fabric channel 1: Ports 1–8 –Fabric channel 2: Ports 9–16 Fabric channel speed 20 Gb/sec (40Gb/sec total) Table 2-60 WS-X6716-10T and WS-X6816-10T-2T/-2TXL Ethernet Module Features (continued) Feature Description
2-112 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 2 Ethernet Switching Modules 10-Gigabit Ethernet Modules Module upgrades available PoE support Not supported. Distributed forwarding support WS-X6716-10T-3C comes factory-equipped with a DFC3C daughter card. WS-X6716-10T-3CXL comes factory-equipped with a DFC3CXL daughter card. NoteThe WS-X6716-10T can be upgraded with the DFC4-E or DFC4-EXL daughter card to operate with the Supervisor Engine 2T. WS-X6816 -10T-2T comes factory-equipped with a DFC4-E daughter card. WS-X6816-10T-2TXL comes factory-equipped with a DFC4-EXL Pluggable transceivers supportNo Digital Optical Monitoring (DOM) supportNo Module front panel LEDsSTATUS Green—All diagnostics pass; the module is operational. Orange—The module is booting or running diagnostics; an overtemperature condition has occurred. LINK Green—The port is active (the link is connected and operational). Flashing orange—The port failed diagnostics and is disabled. Orange—The port is disabled. Red—The module is resetting; an overtemperature condition has occurred. NoteIf the module fails to download code and configuration information successfully during the initial reset, the LED stays red; the module does not come online. Off—The port is not active or the link is not connected. Table 2-61 WS-X6716-10T and WS-X6816-10T-2T/-2TXL Ethernet Module Physical and Environmental Specifications Item Specification Dimensions 1.2 x 14.4 x 16 in. (3.0 x 35.6 x 40.6 cm). Occupies one slot in the chassis. Weight 17.71 lb (8.03 kg) Table 2-60 WS-X6716-10T and WS-X6816-10T-2T/-2TXL Ethernet Module Features (continued) Feature Description
2-113 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 2 Ethernet Switching Modules 10-Gigabit Ethernet Modules Power and heat numbersWS-X6716-10T-3C (base module + the DFC3C daughter card)—11.53 A –Module power—484.26 W –AC-input power—605.33 W –AC heat dissipation—2067.18 BTU/hour –DC-input power—650.89 W –DC heat dissipation—2222.78 BTU/hour WS-X6716-10T-3CXL (base module + the DFC3CXL daughter card)—12.23 A –Module power—513.66 W –AC-input power—642.08 W –AC heat dissipation—2192.69 BTU/hour –DC-input power—690.40 W –DC heat dissipation—2357.73 BTU/hour WS-X6816-10T-2T (base module + the DFC4-E daughter card)—12.26 A –Module power—514.96 W –AC-input power—643.65 W –AC heat dissipation—2198.06 BTU/hour –DC-input power—692.10 W –DC heat dissipation—2363.51 BTU/hour WS-X6816-10T-2TXL (base module + the DFC4-EXL daughter card)—12.62 A –Module power—529.96 W –AC-input power—662.55 W –AC heat dissipation—2262.61 BTU/hour –DC-input power—712.42 W –DC heat dissipation—2432.91 BTU/hour Table 2-61 WS-X6716-10T and WS-X6816-10T-2T/-2TXL Ethernet Module Physical and Environmental Specifications (continued) Item Specification
2-114 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 2 Ethernet Switching Modules 10-Gigabit Ethernet Modules WS-X6908-10G Ethernet Module The WS-X6908-10G Ethernet module (Figure 2-29) provides 8 10-Gbps full- or half-duplex copper ports. Table 2-62 lists the module features, and Table 2-63 lists the module physical and environmental specifications. Figure 2-29 WS-X6908-10GEthernet Module Front Panel NoteThe WS-X6908-10G is the product identifier on the module front panel. The two orderable product IDs for the module are WS-X6908-10G-2T (equipped with a WS-F6K-DFC4-E daughter card) and WS-X6908-10G-2TXL (equipped with WS-F6K-DFC4-EXL daughter card). Environment Operating temperature Certified for operation: 32° to 104°F (0° to 40°C) Designed and tested for operation: 32° to 130°F (0° to 55°C) Humidity (RH) ambient (noncondensing)10 to 90% Operating altitude Certified for operation: 0 to 6500 ft (0 to 2000 m) Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m) Table 2-61 WS-X6716-10T and WS-X6816-10T-2T/-2TXL Ethernet Module Physical and Environmental Specifications (continued) Item Specification Table 2-62 WS-X6908-10G Ethernet Module Features Feature Description Ports per module 8 ports 1 port group Port ranges per port group: 1–8 Port connector type Either SC, RJ45, or InfiniBand depending on the type of X2 transceiver installed in the module port. Cabling distance Dependent on the type of X2 transceiver installed in the module port. For cabling distances, refer to the transceiver installation guides at the following url: http://www.cisco.com/en/US/products/hw/modules/ps5455/prod_insta llation_guides_list.html Maximum frame size Up to 9216 bytes 330213
2-115 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 2 Ethernet Switching Modules 10-Gigabit Ethernet Modules Module oversubscription rate 1:1 Supervisor engine support Supervisor Engine 2T Software support 12.2(50)SY Queues per port Tx—1p7q4t per port Rx—8q4t per port Chassis/slot restrictions Not supported in non E-series Catalyst 6500 switches Requires that modules be installed in adjacent slots or, if either adjacent slot is unused, you must install a switching-module filler plate (Cisco part numbers WS-X6K-SLOT-CVR-E or SLOTBLANK-09) rather than a blank slot cover (WS-X6K-SLOT-CVR) to maintain an adequate air flow through the chassis. Fabric connection Dual 40 Gbps switch-fabric connections Fabric Channel 1: Ports 2, 3, 6, 8 Fabric Channel 2: Ports 1, 4, 5, 7 Fabric channel speed 80 Gb/sec full duplex Module upgrades available PoE support Not supported. Distributed forwarding support Supports either the WS-F6K-DFC4-E or WS-F6K-DFC4-EXL Pluggable transceivers support10GBASE-X X2 transceivers Table 2-62 WS-X6908-10G Ethernet Module Features (continued) Feature Description
2-116 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 2 Ethernet Switching Modules 10-Gigabit Ethernet Modules Digital Optical Monitoring (DOM) supportNo Module front panel LEDsSTATUS Green—All diagnostics pass; the module is operational. Orange—The module is booting or running diagnostics; an overtemperature condition has occurred. LINK Green—The port is active (the link is connected and operational). Flashing orange—The port failed diagnostics and is disabled. Orange—The port is disabled. Red—The module is resetting; an overtemperature condition has occurred. NoteIf the module fails to download code and configuration information successfully during the initial reset, the LED stays red; the module does not come online. Off—The port is not active or the link is not connected. ID Blinking blue—The module is being identified for attention. The LED is turned on by the user to aid servicing personnel in identifying the module. Off—The module is not being identified. Table 2-63 WS-X6908-10G Ethernet Module Physical and Environmental Specifications Item Specification Dimensions 1.73 x 14.4 x 16 in. (4.4 x 36.6 x 40.6 cm). Occupies one slot in the chassis. Weight 12.6 lb (5.72 kg) Table 2-62 WS-X6908-10G Ethernet Module Features (continued) Feature Description
2-117 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 2 Ethernet Switching Modules 10-Gigabit Ethernet Modules Power and heat numbersWS-X6908-10G-2T (base module + the DFC4-E daughter card)—14.00 A –Module power—488.0 W –AC-input power—610.05 W –AC heat dissipation—2083.32 BTU/hour –DC-input power—655.97 W –DC heat dissipation—2240.13 BTU/hour WS-X6908-10G-2TXL (base module + the DFC4-EXL daughter card)—14.36 A –Module power—603.0 W –AC-input power—753.90 W –AC heat dissipation—2574.57 BTU/hour –DC-input power—810.65 W –DC heat dissipation—2768.35 BTU/hour Environment Operating temperature Certified for operation: 32° to 104°F (0° to 40°C) Designed and tested for operation: 32° to 130°F (0° to 55°C) Humidity (RH) ambient (noncondensing)10 to 90% Operating altitude Certified for operation: 0 to 6500 ft (0 to 2000 m) Designed and tested for operation: –200 to 10,000 ft (–60 to 3000 m) Table 2-63 WS-X6908-10G Ethernet Module Physical and Environmental Specifications (continued) Item Specification
2-118 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 2 Ethernet Switching Modules 40-Gigabit Ethernet Modules 40-Gigabit Ethernet Modules This section describes the following 40-Gigabit Ethernet modules: WS-X6904-40G Ethernet Module, page 2-118 WS-X6904-40G Ethernet Module The WS-X6904-40G Ethernet module (Figure 2-30) has four optics bays that can accept four 40-Gigabit Ethernet CFP optics modules or four FourX adapters each providing four 10-Gigabit ports (using SFP+ transceivers). The ports can also be mixed between 40-Gigabit and 10-Gigabit transceivers. Table 2-64 lists the module features, and Table 2-65 lists the module physical and environmental specifications. Figure 2-30 WS-X6904-40GEthernet Module Front Panel NoteThe WS-X6904-40G is the product identifier on the module front panel. The two orderable product IDs for the module are WS-X6904-40G-2T (equipped with a WS-F6K-DFC4-E daughter card) and WS-X6904-40G-2TXL (equipped with WS-F6K-DFC4-EXL daughter card). 332886
2-119 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 2 Ethernet Switching Modules 40-Gigabit Ethernet Modules Table 2-64 WS-X6904-40G Ethernet Module Features Feature Description Ports per module 4 ports—four 40-Gigabit CFP optics modules (ports 1 through 4) 16 ports—four 10-Gigabit FourX adapters (ports 5 through 20) NoteEach of the four optics bays on the module front panel can accept either one CFP transceiver module (one 40-Gigabit port) or a FourX converter and up to four SFP+ transceivers (four 10-Gigabit ports). The module can also support a mix of both 40-Gigabit CFP optics modules and 10-Gigabit SFP+ transceivers (two 40-Gigabit ports and 16 10-Gigabit ports). Port connector type MPO/MTP connector for the 40-Gigabit CFP transceiver module. LC connector for the 10- Gigabit SFP+ transceiver. Cabling distance Dependent on the type of transceiver installed. See the transceiver data sheets or the transceiver installation notes for specific information on cabling distances with the each transceiver type. Maximum frame size Up to 9216 bytes Supervisor engine support Supervisor Engine 2T-10GE only Software support 15.0(1)SY1 or higher Queues per port 40-Gigabit Ethernet ports: –Tx—1p7q4t –Rx—1p7q4t 10-Gigabit Ethernet ports: –Tx—1p7q4t –Rx—8q4t Chassis/slot restrictions Not supported in non E-series Catalyst 6500 switches Supported in a WS-C6503-E chassis with a hardware revision 1.3 or higher Requires that modules be installed in adjacent chassis slots or, if either adjacent slot is unused, you must install a switching-module filler plate (Cisco part numbers WS-X6K-SLOT-CVR-E or SLOTBLANK-09) rather than a blank slot cover (WS-X6K-SLOT-CVR) to maintain an adequate air flow through the chassis.
2-120 Catalyst 6500 Series Ethernet Modules Installation Guide OL-6265-04 Chapter 2 Ethernet Switching Modules 40-Gigabit Ethernet Modules Fabric connection Dual 40 Gbps switch-fabric connections Fabric Channel 1: Ports 1 and 2 (40-Gigabit ports) or 5 through 12 (10-Gigabit ports) Fabric Channel 2: Ports 3 and 4 (40-Gigabit ports) or 13 through 20 (10-Gigabit ports) Fabric channel speed 80 Gb/sec full duplex Module upgrades available PoE support Not supported. Distributed forwarding support Supports only the WS-F6K-DFC4-E or the WS-F6K-DFC4-EXL Pluggable transceivers support Supports 40-Gigabit CFP optical modules Supports 10-Gigabit SFP+ transceivers using FourX converters NoteNot all 40-Gigabit CFP optical modules or SFP+ transceivers may be supported. For an up-to-date list of supported CFP optical modules and SFP+ transceivers along with software requirements, refer to either the 40-Gigabit Ethernet Transceivers Compatibility Matrix or the 10-Gigabit Ethernet Transceivers Compatibility Matrix both available on cisco.com. Table 2-64 WS-X6904-40G Ethernet Module Features (continued) Feature Description