Brother HL 7050N User Manual

							3 - 27 CONTROL PANEL
HL7050_US_UG_FM5.5
PRINT MENU
Display ShowsDescription
MEDIA TYPE=PLAIN PAPER/TRANSPARENCIES/THICK PAPER/
THICKER PAPER/BOND PAPER/ENVELOPES/THIN 
PAPER
PAPERSet the paper size to LETTER, LEGAL, A4, EXECUTIVE, 
COM-10, DL, JIS B5, B5, A5, B6, A6, MONARCH, C5 and 
A4 LONG.
COPIESYou can check the total number of printed pages.
Shows the number of printed pages (1 to 999).
ORIENTATIONThis printer can print pages in portrait or landscape 
orientation.
PORTRAIT or LANDSCAPE
PRINT POSITIONThis printer can be adjusted to align the page format.
Subsetting Description
X OFFSET=0=-500:+500
Move the print start position (at the 
top-left corner of pages) horizontally 
up to -500 (left) to +500 (right) dots in 
300 dpi.
Y OFFSET=0=-500:+500
Move the print start position (at the 
top-left corner of pages) vertically up 
to -500 (up) to +500 (down) dots in 
300 dpi.
AUTO FF TIME=OFF/1:99 (sec)
Allows you to print the remaining data without pressing the 
Go button.
FF SUPPRESS=OFF/ON
Turns the feed suppress (PAUSE) setting ON or OFF.
HP LASERJETSubsetting Description
FONT NO.=I000:####
FONT PITCH=##.##
SYMBOL SETPC-8/...
Set the symbol set or the character set.
TABLE PRINTPrint code table.
AUTO LF=OFF/ON
ON: CR→CR+LF,
OFF: CR→CR
 
						

							CONTROL PANEL 3 - 28
HL7050_US_UG_FM5.5
HP LASERJET
(continued)Subsetting Description
AUTO CR=OFF/ON
ON: LF LF+CR, FF+CR, or 
VT→VT+CR
OFF: LF→LF, FF→FF, or VT→VT
AUTO WRAP=OFF/ON
Select whether a line feed and 
carriage return will happen when the 
printer reaches the right margin.
AUTO SKIP=ON/OFF
Select whether a line feed and 
carriage return will happen when the 
printer position reaches the bottom 
margin.
LEFT MARGIN=##
Set the left margin at column 0 to 70 
columns at 10 cpi.
RIGHT MARGIN=##
Set the right margin at column 10 to 
80 columns at 10 cpi.
TOP MARGIN=#.##
Set the top margin at a distance from 
the top edge of the paper: 0, 0.33, 
0.5, 1.0, 1.5 or 2.0. The factory 
setting is 0.5.
BOTTOM MARGIN=#.##
Set the bottom margin at a distance 
from the bottom edge of the paper - 
0, 0.33, 0.5, 1.0, 1.5 or 2.0. The 
factory setting is 0.33(None-HP), 
0.5(HP).
LINES=###
Set the number of lines on each page 
from 5 to 128 lines.
EPSON FX-850 FONT NO.=I000:####
FONT PITCH=##.##
CHARACTER SETPC-8/...
Set the symbol set or the character set.
TABLE PRINTPrint code table.
PRINT MENU (continued)
Display ShowsDescription
 
						

							3 - 29 CONTROL PANEL
HL7050_US_UG_FM5.5
EPSON FX-850
(continued)Subsetting Description
AUTO LF=OFF/ON
ON: CR→CR+LF
OFF: CR→CR
AUTO MASK=OFF/ON 
LEFT MARGINSet the left margin at column 0 to 70 
columns at 10 cpi.
RIGHT MARGINSet the right margin at column 10 to 
80 columns at 10 cpi.
TOP MARGINSet the top margin at a distance from 
the top edge of the paper - 0, 0.33, 
0.5, 1.0, 1.5 or 2.0. The factory 
setting is 0.33.
BOTTOM MARGINSet the bottom margin at a distance 
from the bottom edge of the paper - 
0, 0.33, 0.5, 1.0, 1.5 or 2.0. The 
factory setting is 0.33.
LINESSet the number of lines on each page 
from 5 to 128 lines.
IBM PROPRINTER FONT NO.=I000:####
FONT PITCH=##.##
CHARACTER SETPC-8/...
Set the symbol set or the character set.
TABLE PRINTPrint code table.
AUTO LF=OFF/ON
ON: CR→CR+LF,
OFF: CR→CR
AUTO CR=OFF/ON
AUTO MASK=OFF/ON
LEFT MARGINSet the left margin at column 0 to 70 
columns at 10 cpi.
RIGHT MARGINSet the right margin at column 10 to 
80 columns at 10 cpi.
PRINT MENU (continued)
Display ShowsDescription
 
						

							CONTROL PANEL 3 - 30
HL7050_US_UG_FM5.5
IBM PROPRINTER
(continued)Subsetting Description
TOP MARGINSet the top margin at a distance from 
the top edge of the paper - 0, 0.33, 
0.5, 1.0, 1.5 or 2.0. The factory 
setting is 0.33.
BOTTOM MARGINSet the bottom margin at a distance 
from the bottom edge of the paper - 
0, 0.33, 0.5, 1.0, 1.5 or 2.0. The 
factory setting is 0.33.  
LINESSet the number of lines on each page 
from 5 to 128 lines.
HP-GL CHAR SET(STD)=####
CHAR SET(ALT)=####
PEN # SIZEPEN1 to 6
(Set size and gray percentage for the 
selected pen.)
PEN # GRAYPEN1 to 6
15, 30, 45, 75, 90 or 100 %
(# is the selected pen number)
BR-SCRIPT3 ERROR PRINT=OFF/ON
PRINT MENU (continued)
Display ShowsDescription
 
						

							3 - 31 CONTROL PANEL
HL7050_US_UG_FM5.5   
NETWORK (only on a Network)
Display ShowsDescription
TCP/IPSubsetting Description
TCP/IP ENABLE=ON/OFF
IP ADDRESS=###.###.###.###
SUBNET MASK=###.###.###.###
GATEWAY=###.###.###.###
IP BOOT TRIES=#
IP METHOD
=AUTO/STATIC/RARP/BOOTP/DHCP
NETWARE NETWARE ENABLE=ON/OFF
NET FRAME=AUTO/8023/ENET/8022/SNAP
APPLETALK=ON/OFF
NETBEUI=ON/OFF
DLC/LLC=ON/OFF
BANYAN=ON/OFF
LAT=ON/OFF
NETBIOS/IP=ON/OFF
APIPA=ON/OFF
ENET
=AUTO/100B-FD/100B-HD/10B-FD/10B-HD
 
						

							CONTROL PANEL 3 - 32
HL7050_US_UG_FM5.5
INTERFACE
Display ShowsDescription
SELECT=AUTO/PARALLEL/RS-232C/USB/NETWORK
AUTO IF TIME= 1:99 (sec)
You need to set the time-out period for the auto interface 
selection. 
INPUT BUFFER= Level1:15
Increase or 
decrease the input 
buffer capacity.RESTART PRINTER?
PARALLELWhen using the parallel interface
Sub-setting Menu Description
HIGH SPEED=ON/OFF
Turns high-speed parallel 
communications on or off.  
BI-DIR=ON/OFF
Turns bi-directional parallel 
communications on or off.  
RS-232CWhen using the serial interface
Sub-setting Menu Description
FAX MODE=OFF/ON RESTART PRINTER?
BAUDRATE 
*1Data transfer speed can be set to 
150/300/600/1200/2400/4800/9600/
19200/38400/57600/115200 baud.
CODETYPE 
*1=8 BITS/7 BITS
The data length can be set to 7 or 8 
bits.
PARITY 
*1=NONE/ODD/EVEN
The data error check can be set to 
NONE, ODD or EVEN.
STOP BIT 
*1=1 BITS/2 BITS
The data separator can be set to 1 or 
2 stop bits.
XON/XOFF 
*1=ON/OFF 
Handshake protocol can be set to on 
or off.  
 
						

							3 - 33 CONTROL PANEL
HL7050_US_UG_FM5.5
*1Appears when FAX MODE is off.
*2Appears when FAX MODE is on.
RS-232C
(continued)Sub-setting Menu Description
DTR(ER)
*1=ON/OFF
ROBUST XON 
*1=OFF/ON
RING DELAY 
*2=0/1/2/3/4
REDUCTION 
*2=AUTO/OFF/90%
RAM SIZE 
*2=1:##MBYTE
RECEIVE 
*2=ON/OFF
INTERVAL 
*2=OFF/6H/12H/24H/2D/4D/7D
RESET MENU
Display ShowsDescription
RESET PRINTERResets the printer and restores all printer settings (including 
command settings) to settings you have previously made 
with the control panel buttons.
FACTORY RESETResets the printer and restores all printer settings (including 
command settings) to the factory settings. See 
List of 
factory settings
 in this chapter.
INTERFACE (continued)
Display ShowsDescription
 
						

							CONTROL PANEL 3 - 34
HL7050_US_UG_FM5.5
Set date and time
Press the + or - button until the SETUP mode 
appears (and to display each setting shown below).
Press the Set button, and then press the 
+or - button until DATE & TIME appears.
Press the Set button, and then press the 
+or - button until YEAR appears.
Press the Set button.
Press the + button.
Press the Set button.
Press the Set button.
Press the Set button.
--MENU--
INFORMATION
--MENU--
SETUP
SETUP 
DATE & TIME
DATE & TIME
YEAR
YEAR
=1999          *
YEAR
=2000
YEAR
=2000          *
DATE & TIME
YEAR
DATE & TIME
MONTH
DATE & TIME
2000/04/25 10:22
 
						

							3 - 35 CONTROL PANEL
HL7050_US_UG_FM5.5
Set IP Address
Press the + or - button until the NETWORK mode 
appears (and to display each setting shown below).
Press the Set button.
Press the Set button.
Press the + button.
Press the Set button.
The last digit in the first part of the number 
is blinking.
Press the + or - button to increase or 
decrease the number.
Press the Set button to go to the next 
number. 
Repeat this process until you have set your 
IP address.
Press the Set button to complete the IP 
address.
An asterisk appears at the end of the 
display.
--MENU--
INFORMATION
--MENU--
NETWORK
NETWORK
TCP/IP
TCP/IP 
TCP/IP ENABLE
TCP/IP
IP ADDRESS=
IP ADDRESS=
192.0.0.192     *
IP ADDRESS=
123.0.0.192
IP ADDRESS=
123.45.67.89 
IP ADDRESS=
123.45.67.89   *
 
						

							CONTROL PANEL 3 - 36
HL7050_US_UG_FM5.5
About emulation modes
This printer has the following emulation modes.  
HP LaserJet Mode
The HP LaserJet mode (or HP mode) is the emulation mode in which 
this printer supports the PCL6 language of the Hewlett-Packard 
LaserJet laser printer.  Many software applications support this type 
of laser printer.  Using this mode will allow your printer to operate at 
its best with those applications. 
BR-Script 3 Mode
BR-Script is an original Brother page description language and a 
PostScript
® language emulation interpreter. This printer supports 
level 3. The BR-Script interpreter of this printer allows you to control 
text and graphics on pages. 
For technical information about PostScript commands, see the 
following manuals:   
■Adobe Systems Incorporated. PostScript Language Reference 
Manual, 3rd Edition. Menlo Park: Addison-Wesley Publishing 
Company, Inc., 1999.
■Adobe Systems Incorporated. PostScript Language Program 
Design. 
Menlo Park: Addison-Wesley Publishing Company, Inc., 1988.
■Adobe Systems Incorporated. PostScript Language Reference 
Manual. Menlo Park: Addison-Wesley Publishing Company, Inc., 
1985.
■Adobe Systems Incorporated. PostScript Language Tutorial and 
Cookbook. Menlo Park: Addison-Wesley Publishing Company, 
Inc., 1985. 
■Adobe Systems Incorporated. PostScript Language Reference 
Manual, third Edition. Addison-Wesley Longman, Inc., 1999.