Xerox Phaser 3200MFP User Manual

							9 Maintenance 
Xerox Phaser 3200MFP9-5
6.Locate the long strip of glass 
(LSU) inside the top of the 
cartridge compartment. Gently 
wipe the glass to remove any 
toner.
7.Re-insert the manual tray, print 
cartridge and close the door.
8.Plug in the power cord and 
switch on the machine.
Cleaning the Scan Unit
Keeping the scan unit clean helps ensure the best possible scanned images. 
We suggest that you clean the scan unit at the start of each day and during 
the day, as needed.
1.Slightly dampen a soft lint-free cloth or paper towel with water.
2.Open the document cover.
3.Wipe the surface of the document glass and ADF glass until it is clean 
and dry.
4.Wipe the underside of the white document cover and white bar until it is 
clean and dry.
5.Close the document cover.
Document cover
Document glass
White bar
ADF glass
Downloaded From ManualsPrinter.com Manuals 
						

							9 Maintenance 
9-6Xerox Phaser 3200MFP
Maintaining the Print Cartridge
Print Cartridge Storage
To get the most from the print cartridge, follow these guidelines:
• Do not remove the print cartridge from its package until you are ready to 
install it. 
• Do not refill the print cartridge. 
The machine warranty does not cover 
damage caused by using a refilled cartridge.
• Store print cartridges in the same environment as your machine.
• To prevent damage to the print cartridge, do not expose it to light for more 
than a few minutes.
Expected Cartridge Life
The life of the Print Cartridge depends on the amount of toner that print jobs 
require. When printing text at ISO 19752 5% coverage, a new print cartridge 
lasts an average of 2,000/3,000 pages. (The original print cartridge supplied 
with the machine lasts an average of 1,500 pages.) The actual number may 
be different depending on the print density of the page you print. If you print a 
lot of graphics, you may need to change the cartridge more often.
Redistributing Print Cartridge Toner
When the print cartridge is near the end of its life, white streaks or light printing 
may occur. The LCD displays the warning message, “Toner Low”. You can 
temporarily recover print quality by redistributing the remaining toner in the 
cartridge. In some case, white streaks or light printing still occurs even after 
you have redistributed the toner.
1.Open the front door.
Downloaded From ManualsPrinter.com Manuals 
						

							9 Maintenance 
Xerox Phaser 3200MFP9-7
2.Pull the print cartridge out and 
remove it from the printer. 
3.Thoroughly shake the print 
cartridge from side to side five or 
six times to redistribute the toner.
NOTE: If toner gets on your 
clothing, wipe it off with a dry cloth 
and wash clothing in cold water. Hot 
water sets toner into fabric.
CAUTION: Do not touch the green 
underside of the print cartridge. 
Use the handle on the cartridge to avoid touching this area. 
4.Reinstall the cartridge and close the front door. Make sure that the cover 
is securely closed. If it is not firmly closed, printing error may occur.
Replacing the Print Cartridge
When the display on the control panel shows the warning message, “Toner 
Empty” the print cartridge has run and the machine stops printing.   At this 
stage, the print cartridges needs to be replaced.
Remove the old print cartridge and install a new print cartridge. See Installing 
the Print Cartridge on page 2-4.
Downloaded From ManualsPrinter.com Manuals 
						

							9 Maintenance 
9-8Xerox Phaser 3200MFP
Printing continuously when the Toner Empty Replace 
Toner message appears
When the toner cartridge is nearly empty, the machine shows the Toner Empty 
Replace Toner message and stops printing. You can set the machine to 
disregard this message when it appears and to continue printing, even though 
print quality is not optimal.
1.Press Menu until “Machine Setup” appears on the top line of the display.
2.Press the scroll button (  or  ) until “Ignore Toner” appears on the bottom 
line of the display.
3.Press the scroll button (  or  ) to display “On” on the bottom line and 
press Enter.
If you select Off, the received fax cannot be printed until you install a new 
toner cartridge. However, faxes can be received into memory as long as 
it allows.
4.To return to Standby mode, press Stop/Clear.
Setting the Notify Toner Option 
If you set the Notify Toner menu option to “On”, your machine automatically 
sends a fax to your service agent or the dealer to notify them. The fax number 
can be preset by your service agent or dealer when the machine is installed.
The machine sends out a notification when:
•  The print cartridge is low.
•  A critical error occurred at your machine.
(Error cases: CRU Fuse Error, Low Heat Error, LSU Error.)
•  Notification day and notification pages that are preset by your dealer have 
passed.
1.Press Menu on the control panel until “Maintenance” appears on the top 
line of the display. 
2.Press the scroll button (  or  ) to display “Notify Toner ” on the bottom 
line and press Enter.
3. Enter a four-digit password you want to use, using the number keypad 
and press Enter.
(If you select this menu, for the first time after purchasing or after clearing 
all memory, re-enter the password to confirm it and press Enter.)
4.Press the scroll button (  or  ) to change the setting. 
Select “On” to enable this feature. 
Selecting “Off” disables this feature.
5.Press Enter to save the selection.
6.To return to Standby mode, press Stop/Clear.
Downloaded From ManualsPrinter.com Manuals 
						

							9 Maintenance 
Xerox Phaser 3200MFP9-9
Cleaning the Drum
You can clean the OPC drum in the print cartridge manually or automatically.
If there are streaks or spots on your prints, the OPC drum in the print cartridge 
may require manual cleaning.
1.Before starting the cleaning procedure, make sure that paper is loaded in 
the machine. 
2.Press Menu on the control panel until “Maintenance” appears on the top 
line of the display. The first available menu item, “Clean Drum”, displays 
on the bottom line.
3.Press Enter. The first available menu item, “Yes” displays on the bottom 
line.
4.Press Enter. The machine prints out a cleaning page. Toner particles on 
the drum surface adhere to the paper. 
5.If the problem remains, repeat steps 1 through 4.
6.To return to Standby mode, press Stop/Clear.
Downloaded From ManualsPrinter.com Manuals 
						

							9 Maintenance 
9-10Xerox Phaser 3200MFP
Consumables Parts
From time to time, you need to replace the Print Cartridge to maintain optimum 
performance and to avoid print quality problems.
The following items should be replaced after you have printed the specified 
number of pages:
To purchase consumables parts, contact your Dealer or Service Agent or the 
Retailer where you bought your machine. We strongly recommend that these 
items are installed by a trained service professional, except for the print 
cartridge.
For the print cartridge refer to Replacing the Print Cartridge on page 9-7.
Replacement Parts
From time to time, you need to replace the ADF Rubber Pad to maintain 
optimum performance and to avoid print quality problems and paper feed 
problems resulting from worn parts.
The following item should be replaced after you have printed the specified 
number of pages:
NOTE: If a ADF rubber pad is required, please contact your dealer or Xerox 
representative.
For the ADF rubber pad refer to Replacing the ADF Rubber Pad on page 9-11.
ItemsYield (Average)
Print Cartridge (initial) Approx. 1,500 pages
Print Cartridge (replacement)Approx. 2,000 pages
Approx. 3,000 pages
ItemsYield (Average)
ADF rubber pad Approx. 20,000 pages
Downloaded From ManualsPrinter.com Manuals 
						

							9 Maintenance 
Xerox Phaser 3200MFP9-11
Replacing the ADF Rubber Pad
You can purchase an ADF rubber pad from your Service Agent or the Retailer 
where you bought your machine.
1.Open the ADF cover.
2.Remove the ADF rubber pad 
from the ADF, as shown.
3.Install a new ADF rubber pad.
4.Close the ADF cover.
Downloaded From ManualsPrinter.com Manuals 
						

							9 Maintenance 
9-12Xerox Phaser 3200MFP
Downloaded From ManualsPrinter.com Manuals 
						

							10 Troubleshooting 
Xerox Phaser 3200MFP10-1
10 Troubleshooting
This chapter gives helpful information for what to do if you encounter an error.
This chapter includes:
• Clearing Document Jams – page 10-2
• Clearing Paper Jams – page 10-4
• Solving Other Problems – page 10-14
Downloaded From ManualsPrinter.com Manuals 
						

							10 Troubleshooting 
10-2Xerox Phaser 3200MFP
Clearing Document Jams
When a document jams while passing through the ADF (Automatic Document 
Feeder), “Document Jam/Remove&Reload” appears on the display.
Input Misfeed
1.Remove any remaining page(s) from the ADF and input tray.
2.Open the ADF cover.
3.Pull the document gently out of the 
ADF.
4.Close the ADF cover. Then load the 
removed page(s), if any, back into the 
ADF.
NOTE: To prevent document jams, use 
the document glass for thick, thin, or 
mixed paper-type documents.
Downloaded From ManualsPrinter.com Manuals