Vodavi Starplus Triad S Description Manual

Station Attributes Programming
Page A Introduction
Lihe Queuing
Programming Steps
IPress the QUEUING flexible button (FLASH 50, Page A, button #7). The following
message displays:
.
LINE QUEUINGO-lENABLEDl
zEnter a l-digit value on the dial pad to enable/disable the Line Queuing feature.
[0] = Disabled
[I] = Enabled
3Press HOLD to save the entry. Confirmation tone is heard.
Description
‘\.
Stations can be allowed or denied the ability to manually queue for a busy group of CO lines. Even when
disabled,...

Station Attributes Programming
Page A IntroductionOff-Hook Voice Over (OHVO)
Programming Steps
1Press the OHVO flexible button (FLASH 50, Page A, button #g). The following
message displays:
OFF HOOK VOICE OVERO-1
DISABLED
.2Enter a l-digit value on the dial pad to enable/disable the Off-Hook Voice Over
feature.
[0] = Disabled
[I] = Enabled
3Press HOLD to save the entry. Confirmation tone is heard.
Description
When enabled, this feature allows a digital station to receive OHVO while on a call. A station...

Station Attributes Programming
Page A introduction
Description
Stations can be allowed or denied the ability to forward incoming CO calls, intercom calls, or transferred
.F.-.+---. iz:--63_ ..--. >.outside lines to another station or group. By default, Call Forwarding is enabled at all stations.
Forced Least Cost Routing (LCR)
Programming Steps
1Press the FORCED LCR flexible button (FLASH 50, Page A, button #II). The following
message displays:
FORCE LCRo-1DISABLED
2Enter a l-digit value on the dial pad...

4-10Station Attributes Programming
Page A Introduction
3Press HOLD to save the entry. Confirmation tone is heard,
The use of Supervisor Monitor with Barge-In is limited by 
federal low and
mayalso belimitedorprohibitedbystote orlocallaw, so check fherelevant,.laws in your area before employing these features._,1‘,;;-;;: ,,A change in volume may occur on the CO line or intercom call offer the
barge-in occurs.
Description
Eh%feature k avadable with optiomzlsoftware. The ACD Supervisor Monitor with Barge-In...

Station Attributes Programming
Page A Introduction
Description
The Executive Override Feature has a separate condition added to it that allows or disallows an Executive to
+,-7.
c.-;
; _,.:,.Goverride an extension. This prevents an extension with override capability from overriding an Executive’s
.‘.2station. By default, Executive Override is enabled at all stations.The Executive Override blocking feature also blocks an 
AC0 Supervisor
Monitor with Barge-/n.
CO Line Ringing Options
Programming Steps...

4-12Station Attributes Programming
Page Blntroduction
Name / Number Display at Idle
Programming Steps
IPress the NAME/NUMBER DISPLAY flexible button (FLASH 50, Page A, button #is).The following message displays:
NAME AT IDLE ICDO-lNAME
2Enter a l-digit value on the dial pad to enable/disable the Name/Number feature.
[0] = Name
[I] = Station Number
3Press HOLD to save the entry. Confirmation tone is heard.
Description
This feature displays the standard idle LCD showing the programmed 7-digit name and...

Station Attributes Programming
Page B IntroductionIf HOLD is pressed without entering a station range, all stations 
(100-131)are selected.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Flexible button 
#24 (New Range) is lit.
4Press [PG B] button. The current programming for those features displays as:
I
XXX-XXX PAGE B
ENTER BUTTON NUMBER
IWhere:
XXX = Station Range (100-131)
Description
This section describes the steps and procedures necessary to program station...

.
Station Attributes Programming
Page B Introduction
Station ldentif ication
Programming Steps
1Press the STATION ID flexible button (FLASH 50, Page B, button #l).
STATION IDo-7
KEYSET
1Enter a 1, 2, 3 or 4-digit value on the dial pad to identify the type of terminal:
[000] or [0] = 24-Button Terminal
[I] = DSS Console
[6] = SLT without Message Wait
[7] = SLT with Message Wait
[007] = 12-Button Terminal
[008] = g-Button Terminal
2Press HOLD to save the entry. A confirmation tone is heard and the display...

Station Attributes Programming
Page B Introduction
STATION IDo-7
DSS MAP X ASSOC XXX
1Where:
x 
=IXXX = Station Range (100-131)
MAP #l by default has all 12 CO Lines and all 32 Stations, 100-131. This provides
12x32 configuration. Station/Feature buttons are flexible and can be changed by the
buttons are NOT changeable.1  128 1
a default layout for a
station user. CO Line
STARPLUS Triad-S System Programming Manualissue I- December 1998 

 I4-16Station Attributes Programming
Page B IntroductionSLT Station ID
Programming Steps
1Dial [6] on the dial pad.
2Press HOLD to save the entry. A confirmation tone is heard and the display updates.
STATION IDo-7SLT
Description
The STARPLUS Triad-ST”’ system supports industry standard 2500-type (DTMF) single line instruments.
When the CSIB is installed in the system, a maximum of 24 single line telephones are supported,
SLT with Message Waiting Lamp Station ID
Programming Steps
1Dial [7] on the dial...