Vodavi Starplus Triad S Description Manual

System Parameters Programming
Access Codes2-69
Other Codes:
III
6=6# l-=13I$=*2 I#=##III
7 = 
7#‘=14& = *4Table 2-8: Dial Pad Keys
3If an error is made while entering the name, press the BACK SPACE flexible button
(FLASH 23, button 
#4). This button backspaces one character at a time.
4Press HOLD to save the entry. A confirmation tone is heard and the display updates.
NAME -A name up to 24-characters may be entered into each directory dial list entry. The names display
alphabetically when accessed by a...

2-70System Parameters Programming
Hunt Groups
2Press HOLD to save the entry. A confirmation tone is heard and the display updates.
The entry is erased (both the 
BIN/KM assignment and the programmed name).
CLEAR - Entries in the table may be erased and cleared from the table allowing placement of another entry
into the list. When a system speed dial bin is deleted or changed the name associated to the bin must also
be erased. When a multiple table listing is associated to one system speed dial bin it may...

System Parameters Programming
Hunt Groups
2-71HUNT GRP 450HUNT
GRP461HUNTGRP452HUNTGRP453
3&m*aQ13 4814HUNT GRP 454HUNT
GRP455HUNTGRP456HUNTGRP457
%+ms-%8- *mrilHUNT GRP 458HUNTGRP459HUNT
GRP460HUNTGRP461
+%19#l!iorxls:-a#II:,STATION 
/
Station / Pilot Hunting Assignment
Programming Steps
1Press the STATION/PILOT flexible button (FLASH 30, button #13) to indicate Station
Hunting or Pilot Hunting.
LED On = Station Hunting enabled
LED Off = Pilot Hunting enabled
To remove stations from a Hunt group:
1Enter...

2-72System Parameters Programming
Hunt Groups
PILOT HUNTING - Incoming CO, transferred CO, and intercom calls can be directed to a pilot number of
a hunt group. The system searches sequentially (in the order the extensions were entered in the database
programming) for an idle station in the group and rings that station. Calls directly to stations (by calling the
extension number) within the hunt group do not hunt but receive call progress tones from the extension,
Verified Account Codes Table/Traveling...

 I  ..System Parameters Programming
Hunt Groups2-73
CLASS OF
DELETE ACCT
-_-;

2-74System Parameters Programming
Hunt Groups
Local Number / Name Translation Table
Programming StepsIPress FLASH and dial 
[55]. The following message displays:
s - xxx #?Y# ,Where:
XXX = Table Number 600-799
### = Route Number 000-199
2The ROUTE NUMBER LED is lit. Enter the 3-digit Route Number (000-199) from what
was entered in program code, FLASH 
[43].
To erase a current phone number and name entry:
IPress the CLEAR ENTRY flexible button (FLASH 55, button #4) to clear an entire
phone number and name...

System Parameters Programming
Hunt Groups2-75
table, the local translation table rules. 200 entries are provided in this table for the Triad-S System. An option
was added to the Local Number/Name translation table to route an ICLID or Caller Entered ID Digits, based
^%.
v-
on a partial compare with the number entered in the translation table.. .._. -,.i:‘ .:3,.‘_ROUTE NUMBER PHONE NUMBER
NAME
CLEAR ENTRY
%ll %%a%s132#6lT--R-lBACKSPACE
#15#1_6#em##18
*-#lm--Fl*lli%Eizzzl
*- +YenSlzcxIa-NEXT TABLEPREV...

2-76System Parameters Programming
Hunt Groups
number identification. If the ICLID option is selected, digits received before the announcement time-out
are captured and inserted as incoming ICLID number information,
When the ICLID option is selected, 
[#] is recognized as an announcement termination and [SC] is
recognized as an entry error. An entry error causes removal of the ICLID and the incoming caller can re-
enter their phone number.
Example: If 602-443 is entered in the translation table with a...

Page A Introduction
Programming Steps
If the system is in the programming mode, continue using the program codes. If starting to program here,
enter the programming mode. Refer to Chapter 1, 
Figure 2-1: Prog~amning Button Mapping. If any CO line
features must be changed
1Press FLASH and dial [40]. The following message displays:
CO LINE ATTRIBUTES
SELECT A CO LINE RANGE
2Enter a 6-digit number for the range of lines being programmed. If only one line is being
programmed, enter that number twice (001...

3-2CO Line Attributes ProgrammingPage A Introduction
DTMF 
/ DPco I PBXUNADISA T I T
Ykkizm *!lcIKi *Is %+;PRIVACYLOOP 
SUPVDISACO GROUP
*LizEEl *- *ilzz!Il *Is
cosRING ASSIGNCO LINE IDTRUNK DIR
*-4%isEzizl*-:%-DISPLAY RING
*- +k-%115 #-;PAGE APAGE B
1117+%- +n $120PAGE CNEXT (FWD)
NEXT (BACK)NEW RANGE
%- %122%?- *Ifaz3zlI
DTMF / Dial Pulse Programming
Programming Steps
1Press the DTMFIDIAL PULSE flexible button (FLASH 40, Button #I).
2Enter a l-digit value (O-l) that corresponds with the following...