Vodavi Starplus Triad S Description Manual

CO Line Attributes ProgrammingPage A introduction
3Press HOLD to save the entry. A confirmation tone is heard.
Description
Each individual outside line connected to the system may be programmed as a CO or PBX line. Use the PBX
mark when identifying 
Centrex lines. By default, all lines are assigned as CO lines.
Universal Night Answer (UNA)
Programming Steps
1Press the UNA flexible button (FLASH 40. Button #3).
2Enter a l-digit value (O-l) which corresponds with the following entries:
[0] = Disabled
[I] =...

CO Line Attributes ProgrammingPage A Introduction
[I] = Enabled
DISA CO TO COO-l
ENABLED
I
3Press HOLD to save the entry. A confirmation tone is heard.
Description
The DISA Trunk-to-Trunk (or Conference) mark on the CO line governs a DISA caller’s ability to access
other outside lines. CO lines must have DISA Trunk-to-Trunk enabled to allow a DISA caller to establish an
outgoing trunk-to-trunk connection. This allows for specific CO line access restriction on DISA calls. A
station with Conference enabled...

CO Line Attributes Programming
Page A Introduction
3Press HOLD to save the entry. A confirmation tone is heard.
Disabling the privacy feature may be limited by federal, state or local law,
so check the relevant laws in your area before disabling privacy.
If desired, the system can be programmed to eliminate CO Line privacy, allowing another station to join
existing outside line conversations.
+Stations must have a direct CO line appearance to join CO line conversations in progress.
9A station must also...

 I3-6CO Line Attributes ProgrammingPage A Introduction
2Enter a l-digit timer value on the dial pad between l-9 which corresponds to 100-900
ms. (0 = disabled)
LOOP SUPERVISION4o-9
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
Loop supervision is used primarily with DISA, Voice Mail/Auto Attendant and with unsupervised conference
applications. It lets the system detect when loop current is broken and an outside line is no longer being
used. To determine...

CO Line Attributes Programming
Page A Introduction
6The system administrator can control the call duration after establishing a Trunk-to-Trunk call,
44After expiration of the Conference Timer, a tone is presented to both DISA parties, then one minute
later the system automatically releases both trunks.
+The Conference Timer does not affect or control a DISA-to-Station call. By default, there are no
outside lines assigned as DISA lines.
Line Group Programming
Programming Steps
1Press the CO LINE GROUP...

3-8CO Line Attributes ProgrammingPage A Introduction
COS4 = Restricts [0], [I], 
[*I, [#] dialed as first-digit and places a 7-digit dialing
limitation. In addition, 
I-800,1911, and 1611 are allowed and 411, 976, and 555 numbers
are denied.
COS5 = Overrides Station COS 2, 3, 4, 5 and allows unrestricted dialing.
I
CLASS OF SERVICE1-51I
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
Through assignments of a CO Class of Service, the assigned CO line...

CO Line Attributes ProgrammingPage A Introduction
CO Line Ringing Assignments
:--
6.;:Programming Steps
.,. ,,,I: ‘f.:1Press the RING ASSIGNMENT flexible button (FLASH 40, Button #IO). The display
shows the following information:
RING ASSIGNMENTS
ENTER DDDR
2Enter the 3-digit destination (DDD) and the l-digit ring type (R) followed by HOLD. A
confirmation tone is heard and the display updates.
DOD = Valid 3-digit Destinations:
[020-0991 = System Speed Bins 20-99, for Off-Net ringing
[IOO-131]= STARPLUS...

 I3-10CO Line Attributes Programming
Page A introduction
Description
Each CO Line may be assigned to ring any station in the system; UCD, Voice Mail or Hunt Group, or Off-Net
(via speed dial). CO Line ringing is programmed on a per CO Line destination basis. Each destination may
be designated to ring during the day, during the night, or receive both Day and Night ringing. Stations that
are assigned for initial ring-in 
must have a LOOP button(s) to answer calls if a direct CO appearance is
unavailable....

CO Line Attributes Programming
Page A Introduction
3ther Codes:
I =I#8 = 8#= 01* = *#
2 = 2#9 = 9#) = 02( = #I
3 = 3#0 = O#?=03 )=#2
4 = 4#Space = 11I = 04+ = #3
5 = 5#: = 12! = *I= = #4
6= 6#-=I3$ = *2# = ##
7 = 7#I= 14& = *4Table 3-4: Dial Pad Keys
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
This feature provides entry of a name for each line (trunk) connected to the system. Once entered into the
database, LCD phones, including the attendant...

3-12CO Line Attributes Programming
Page A Introduction
A message similar to the following display is used for all CO Line displays when a name is programmed for
a CO Line.
.
LINE RINGINGnnnnnnnnnnnnHH:MM amEntries can be made using a keyboard by following the same outlined
procedures using Table 2-6.
Trunk DirectionProgramming Steps
IPress the TRUNK DIRECTION flexible button. (FLASH 40, Button #12). The following
message displays:
I
CO DIRECTIONO-3
INCOMING-OUTGOING
I
2Enter a l-digit value on the dial...