Vodavi Starplus Triad S Description Manual

CO Line Attributes ProgrammingPage A Introduction
Outgoing
4%Outgoing restricts the CO Line to outgoing calls only,
+Users can place call on hold, park the call, and other stations can pick-up the call.
Incoming and Outgoing
QIncoming and outgoing type allow calls to be received or dialed out,
By default, all CO Lines default to both incoming and outgoing type.
Display Ring Assignments
Programming Steps
1Press FLASH 40, Button #I3 to display ring assignments. Assignments are displayed insets of 8, up to...

CO Line Attributes Programming
Page B Introduction
Page B Introduction
Programming Steps
If the system is in the programming mode, continue using the program codes. If starting to program here,
enter the programming mode. If Page B CO Line features must be changed:
1Press FLASH and dial [40]. The following message displays:
I
CO LINE ATTRIBUTES
SELECT A CO LINE RANGE
I
2Enter a 6-digit number for the range of lines being programmed. If only one line is being
programmed, enter that number twice (001...

CO Line Attributes ProgrammingPage B Introduction
When programming the Page B features, the flexible buttons are mapped as follows:XMT VOLUMEP FWD DESTP FWD 
VMIDUDA
#ll *lzIEl*i-3---n*14MOH PER CORING TONE
#czrm*-*-*lT---il
*19# 110 % IAl841131
%-#klTc--FlI115GI2#IlsPAGE APAGE B
Sk-%+-
*a%lm-7-jPAGE CNEXT (FWD)
0121NEXT (BACK)NEW RANGE%1222# ICI*a
Transmit Volume OptionProgramming Steps
IPress the TRANSMIT VOLUME flexible button (FLASH 40, Page B, Button 
#I). The
following message displays:
TRANSMIT...

3-16CO Line Attributes Programming
Page B Introduction
Description
Up to ten volume levels are available for each CO Line in the system. By default, all CO lines are
programmed for level 5 (0 
dB).Do NOT adjust this option without consulting with Technical Support first.
The default settings were set to apply to most applications. Have the 
dBreadings on all CO lines available when calling Technical Support.
Preset Call Forward Destination
Programming Steps
1Press the PRESET FWD DESTINATION flexible...

CO Line Attributes Programming
Page B Introduction
Preset Forward Voicemail ID
@$
Programming Steps
.- -1Press the PRESET FWD VMID flexible button (FLASH 40, Page B, Button #3). The
following message displays:
PRESET FORWARD VMID
zEnter up to four digits on the dial pad that correspond to 0000-9999 for the Voice Mail
ID digits.
3Press HOLD to complete the entry. A confirmation tone is heard and the display updates.
To delete numbers that are currently entered:
IPress [#] four times. Press HOLD to update....

3-18CO Line Attributes Programming
Page B Introduction
can answer that line while the System is in the day mode by dialing a UDA code [#5]. To utilize this feature,
a LOOP button or an appearance of the trunk must be present on the station. By default, the Universal Day
Answer feature is disabled.
Music On Hold (per CO Line)
Programming Steps
1Press the MUSIC-ON-HOLD flexible button (FLASH 40, Page 6, Button #5). The
following message displays:
I
MOH CHANNELO-l1I
2Enter a l-digit value on the dial pad to...

CO Line Attributes Programming
Page B Introduction
2Enter the 2-digit value on the dial pad to change this feature. The ringing choices are:
Tone#FreqTone #Freq
006971770 18
852/I 477
Table 3-5: Ringing Tones
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The tone ring signal used to notify stations of an incoming call can be changed in administrative
programming to provide distinctive ringing on a per CO line basis. A distinctive ring tone can be...

3-20CO Line Attributes Programming
Page C introduction
for each CO line that rings each station. The system provides 36 different ring patterns that can be selected
for each CO 
line in the system. By default, Distinctive Ringing is set for 00 (697/770).
Dis tint tive CO ringing overrides station dis tic tive ringing.
Page C Introduction
Programming Steps
If the system is in the programming mode, continue using the program codes. If starting to program here,
enter the programming mode first.
1Press FLASH...

CO Line Attributes Programming
Page C Introduction
3-21
of CO lines or one specific CO Line. Range programming lets the programmer change a specific parameter or
a few parameters for an entire range of CO lines, leaving intact the remaining data fields that do not require
-;< z,.,
4
=; ‘: ‘;‘;change. Those data fields continue to operate with the previously programmed data. By default, Page A is
.jL..G,Yshown.-.
When programming the Page C features, the flexible buttons are mapped as follows:FLASH...

.3-22
CO Line Attributes Programming
Page C introduction
Ring Delay Timer
Programming Steps
1Press the RING DELAY TIMER flexible button (FLASH 40, Page C. button #2). The
following message displays:
RING DELAY TIMER00-2000
2Enter a 2-digit timer value on the dial pad between 00-20 which corresponds to 00-20
seconds.
3Press HOLD to save the entry. A confirmation tone is heard and the display updates.
Description
The Ring Delay timer was added to the Triad-S to accommodate ICLID interface requirements, The...