Vodavi Starplus Triad S Description Manual
Here you can view all the pages of manual Vodavi Starplus Triad S Description Manual. The Vodavi manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 521
.- CO Line Attributes Programming Page C Introduction3-23 Description This option lets the user adjust the reseize timer on a per CO Line basis. The reseize timer can be used on .$C..;.x c.- sr,..any trunk type. This timer sets the time period that a trunk is held disconnected after receiving a disconnect ‘Gbefore being reseized when a device is queued for a member of the trunk group. By default, the Reseize Timer is set for two seconds. Guard Timer Programming Steps 1Press the GUARD TIMER button (FLASH...
Page 522
3-24CO Line Attributes Programming Miscellaneous CO Parameters Descriptiop This timer determines the time an outside line rings before being forwarded to a predetermined destination, If a forward destination is programmed in the CO line field, the CO calls forward to that destination after the CO preset forward timer expires. This forward occurs regardless of how many stations the line is ringing. The digits entered for the CO line are sent in the station field.This feature applies to initial CO ringing...
Page 523
I :. --. CO Line Attributes Programming Miscellaneous CO Parameters3-25 Dial Pulse Parameters &??,, Pwrammi”g steps
Page 524
3-26CO Line Attributes Programming Miscellaneous CO Parameters issue I- December IQ98STARPLUS Triad-S System Programming ManualI
Page 525
: . . . . --::.. Programming Steps If the system is in the programming mode, continue using the program codes, If starting to program here, enter the programming mode. If station features must be changed: 1Press FLASH and dial [50]. The following message displays: STATION ATTRIBUTES SELECT A STATION RANGE zEnter a 6-digit number for the station range being programmed. If one station is being programmed, enter that number twice (100100). ,-’ ‘. /f HOLD is pressed without entering a station range, ALL...
Page 526
4-2Station Attributes ProgrammingPage A Introduction When programming the Page A features, the flexible buttons are mapped as follows:PAGE ACCESSDO NOT CONFERENCEEXECUTIVE DISTURB OVERRIDE *n %a %+13 %pi--RlPRIVACYSYSTEM SPEEDLINE QUEUING PREF LINEANSWER %15 %+m #ITILl #IT--i-lOHVOCALL FORWARD FORCED LCRACD SUPV BARGE-IN *n%+110 #a %i!cExlEXEC OVRDCO LINE RINGNAME / NUMBER BLOCKINGOPTIONS DISPLAY #L13 *114 Sk+- #CPAGE APAGE B #a 1118 9119e (301PAGE CNEXT (FWD) NEXT (BACK) NEW RANGE %D %kD 1123-%%n...
Page 527
IStation Attributes Programming4-3 Page A Introduction Do Not Disturb Programming StepsPress the DO NOT DISTURB flexible button (FLASH 50. Page A, button #2). The following message displays: I DO NOT DISTURBO-l ENABLED I 2Enter a l-digit value on the dial pad to enable/disable the Do Not Disturb feature. [0] = Disabled [I] = Enabled 3Press HOLD to save the entry. Confirmation tone is heard. Description Stations can be individually allowed or denied the ability to place their telephone in Do Not...
Page 528
Station Attributes ProgrammingPage A introduction Executive Override Programming Steps 1Press the EXECUTIVE OVERRIDE flexible button (FLASH 50, Page A, button #4). The following message displays: EXEC OVERRIDEo-1 DISABLEDl . 2Enter a l-digit value on the dial pad to enable/disable the Executive Override feature. [0] = Disabled [I] = Enabled 3Press HOLD to save the entry. Confirmation tone is heard. Use of this feature when the Executive Override Warning Tone is disabled may be interpreted as a violation...
Page 529
: Station Attributes Programming Page A introduction Privacy (Per Station) ,.-~~, Programming Steps.-A... Tc.;.: =-2 -:>i.
Page 530
I4-6Station Attributes Programming Page A Introduction Privacy is enabled for all stations in default. Station Attempting toCO Line in Use by Another Station Access CO Line Privacy Enabled Privacy DisabledPrivacy EnabledPrivate Private (No Cut-through) (No Cut-through) Privacy DisabledPrivatePrivacy Released (No Cut-through)(Cut-through Allowed) Table 4-l: Station Privacy Flag System Speed Dial Access Programming Steps 1Press the SPEED flexible button (FLASH 50, Page A, button #6). The following message...