Vodavi Starplus Triad S Description Manual
Here you can view all the pages of manual Vodavi Starplus Triad S Description Manual. The Vodavi manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 471
System Parameters Programming Programmable Flash Rates2-49 system configuration to desired flash rates. By default, Line Queue Button flash rate is set for a Red 480 ipm Flutter (08). .-i e”$,$ Do Not Disturb Button Programming Steps 1Press the DND BTN flexible button (FLASH 07, button #18). The following message displays: I DND.BTN00-28 RED STEADY ON I 2Enter a 2-digit value on the dial pad to correspond to one of the 29 available options. Refer to flash rate table. 3Press HOLD to save the entry. A...
Page 472
System Parameters Programming System Parameters Programming Description The Intercom Hold Button flash rate is the rate at which your Hold button flashes when you receive an intercom call and your station’s intercom mode selector switch is in the Tposition. This flash rate can be programmed to 29 different options identified in the flash rate table. This enables the programmer to customize the key system configuration to desired flash rates. By default, Intercom Hold Button flash rate is set for a Red...
Page 473
. . .._ System Parameters Programming System Parameters Programming Description This section describes the procedures and steps necessary to program System Parameters in the System Parameters programming area. The buttons on the digital terminal are illustrated below: LEADING DIGIT 1LEADING DIGIT 2 LEADING DIGIT 3 LEADING DIGIT 4 9kn 012*13#mLEADING DIGIT 5 LEADING DIGIT 6 LEADING DIGIT 7 LEA;FA;LplT %n%1_6%m *!xzil CENTREX DIGITS4 DIGIT VM ID s- *Llirizl*- *EizxzlMUSIC CH #3MUSIC CH #4MUSIC CH #5MUSIC...
Page 474
2-52System Parameters Programming System Parameters Programming Program CodeFLASH 09T-Flex Button 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Feature Leading Digit 1Leading Digit Leading Digit 2None Leading Digit 3None Leading Digit 4None Leading Digit 5None Leading Digit 6None Leading Digit 7None Leading Digit OptionDisabled Centrex Digits4 digits Four Digit Voice Mail ID3 digits Music Channel #3*##Music Channel #4*##Music Channel #5*##Music Channel #6*##Music Channel #7*##Music Channel #8*##...
Page 475
System Parameters Programming System Parameters Programming2-53 [2] = Trunk Group 2 (82) [3] = Trunk Group 3 (83) [4] = Trunk Group 4 (84) [5] = Trunk Group 5 (85) [6] = Trunk Group 6 (86) [7] = Trunk Group 7 (87) [8] = Leading Digit* * 8 is unavailable on button 7 (digit 7), only O-7 are available. 4Press HOLD to save the entry. A confirmation tone is heard and the LCD indicates the change. Description This feature lets the system have the dialing plan modified to accommodate multiple systems...
Page 476
2-54System Parameters Programming System Parameters Programming Description This feature enables/disables the Leading digit Integration feature option on a system-wide basis. By default, this feature is disabled. Centrex Digit Length Programming Steps 1Press the CENTREX DIGITS flexible button (FLASH 09. button #9). The following message displays: CENT;EX DIGITS4-5 2Enter a l-digit value (4-5) that corresponds with the following entries: [4] = Centrex Digit length [5] = Centrex Digit length 3Press HOLD to...
Page 477
System Parameters Programming2-55 System Parameters Programming Description This feature modifies the station and CO voice mail identification fields such that the maximum length of these fields is increased from three digits to four digits. When using leading digit for voice mail IDS, the new number must be entered individually... 2100,2101,2103, etc. This is performed in Flash 50, Page B, Button 13. MOH Assignments Programming Steps 1Press the MUSIC CH # flexible button (FLASH 09, button #I3 through...
Page 478
2-56System Parameters Programming System Parameters Programming 4Press HOLD to save the entry. A confirmation tone is heard and the display updates. Description The system identifies an attendant station for the purpose of receiving recalls and activating night service. The system can have up to three attendant(s) programmed. Entering [#] three times removes that attendant assignment or different station numbers can be programmed. By default, Station 100 is assigned as the first attendant. System Time...
Page 479
System Parameters Programming System Parameters Programming2-57 PBX Dialing Codes Programming Steps 1Press FLASH and dial [12]. The following message displays: PBX DIAL CODES w, H, w, w, ##. zEnter five 2-digit code numbers, one right after the other, on the dial pad up to ten digits. If a single digit code is required, enter the code followed by [#I. 3Press HOLD to save the entry. A confirmation tone is heard and the display updates. 4To delete a code, enter [#I] [#I and press HOLD. Description Five l-...
Page 480
2-58System Parameters Programming System Parameters Programming7To program a fourth pair, press the fourth button in the flexible button field and enter station numbers as in steps 3-5. Description There are four Executive/Secretary pairs available. When an Executive station is busy or in DND, intercom calls and transfers are automatically routed to the designated Secretary.EXEC / SECYEXEC / SECYEXEC / SECYEXEC / SECY PAIR #lPAIR #2PAIR #3PAIR #4 I II 4s 12 * 13 48 I4 The assigned secretary may Camp-On...