Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

Executive Override2-131
Chapter 2 - Features and Operation
DEFAULT…Executive Override is disabled for all stations.
Operation
To use Executive Override, when calling a busy station:
1. Press the preprogrammed EXECUTIVE OVERRIDE button (The programming code is 625).
Executive station is bridged onto the CO line conversation in progress at the called
station. An optional warning tone is presented to all parties prior to cut-through.
2. ReplacehandsetatExecutivestationtoterminatetheoverride.
Conditions
»An...

2-132Executive Override
Chapter 2 - Features and Operation
Programming Steps
1. Press the EXECUTIVE OVERRIDE BLOCK flexible button(FLASH 50, Page A, Button #13).
The following message displays:
2. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT…Executive Override Blocking is disabled at all stations.
Executive Override Warning Tone
Description
The Executive Override Warning enables Executive...

Executive Override2-133
Chapter 2 - Features and Operation
Barge-In Warn Tone
Description
When the Barge-in Warn Tone feature is enabled, it produces a tone to notify a station that
another station is about to use Executive Override or the Barge-in feature to cut into the
existing conversation.
Programming Steps
1. Press the BARGE IN WARN TONE flexible button(FLASH 06, Button #1). The following
message displays:
2. Enter a 0 or 1 on the dial pad to enable/disable the conference tone.
[0] = Disabled
[1] =...

2-134Executive / Secretary Pairs
Chapter 2 - Features and Operation
Executive / Secretary Pairs
Description
There are four Executive/Secretary pairs available. When an Executive station is busy or in
DND, intercom calls and transfers are automatically routed to the designated Secretary.
The assigned secretary may Camp On to the Executive Station when the station is busy or in
Do-Not-Disturb. There can be only one pairing of stations, with no duplicates. You cannot
pair Executive 100 to Secretary 101,...

External Day Ring2-135
Chapter 2 - Features and Operation
External Day Ring
Description
The system can be programmed so CO lines marked for UDA provides ringing out of the
external page ports when the system is in the Day Mode.
Programming Steps
1. Press the EXT DAY RING flexible button(FLASH 06, Button #5). The following message
displays:
2. Enter a 0 or 1 on the dial pad to enable/disable External Day Ring.
[0] = Disabled
[1] = Enabled
3. Press HOLD to save the entry. A confirmation tone sounds....

2-136Fixed Station/Port Number
Chapter 2 - Features and Operation
Fixed Station/Port Number
Description
When a station dials the feature code 611 on a display telephone, it will display the Fixed
Station/Port Number for that telephone. For example, when using flexible numbering some
programming steps require the“FIXED”code. This code allows you to dial 611 and quickly
determine the fixed port for that station.
 SINGLE LINE TELEPHONE
Not applicable
Flash Rates (Programmable)
Description
Fixed and...

Flexible Button Assignment2-137
Chapter 2 - Features and Operation
Flexible Button Assignment
Description
If you have buttons on your telephone, you may program them to suit your own needs. This
feature also allows programming of flexible buttons from a remote location (off-site). Range
programming can also assign these buttons to multiple stations.
The possible functions you may assign to these buttons include:

2-138Flexible Button Assignment
Chapter 2 - Features and Operation
A CO line can be assigned a number between 001 and the maximum number of CO lines
in the system. Additional stations can be added to the system by reducing the number of
CO lines.
Flexible Button
Description
Each Digital Telephone has 8, 12, or 24 flexible buttons that can be programmed. One of the
following six operations can be selected in programming for each button.
To assign a Flexible Button (user programmable):
Enter [BB], [0],...

Flexible Button Assignment2-139
Chapter 2 - Features and Operation
To assign a Feature Button (admin programmable):
Enter [BB], [4], [XXX], [HOLD]
This feature enables flexible buttons to be programmed from a remote location (refer to
“Default Numbering Plan”on page F-16). Range programming can be used to assign these
buttons to multiple stations. When a button is assigned as a feature button [4], the
programmer can program any features on the buttons.
To unassign (lock out) a button:
Enter [BB], [#],...

2-140Flexible Button Assignment
Chapter 2 - Features and Operation
12-BUTTON DEFAULT
8-BUTTON DEFAULT
Programming Steps
1. PressFLASHand dial[50]. Flexible button #24 (New Range) is lit and the following
message displays:
2. Enter the range of station numbers to be programmed. If only one station is being
programmed, enter that number twice, e.g., [100 100].
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Flexible button #19 (Page A) is lit.
4....