Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

Direct Inward Dialing2-101
Chapter 2 - Features and Operation
Route 000in the ICLID Ringing Assignment Table is used as the intercept route. Calls to
numbers not contained in the DID table follow Route 000. If Route 000 is defaulted to None,
the call follows Route 001.
Route 001is used as the Busy DID Route. DO NOT program any entries in this Route if you
intend to provide a busy tone to callers dialing a busy DID/DVIS number.
Programming Steps
PressFLASHand dial[44]. The following message displays:...

2-102Direct Inward Dialing
Chapter 2 - Features and Operation
To change to a different DID Route Number:
1. Press either the UP Button(FLASH 44, Button #18),
-or-
Press the DOWN Button(FLASH 44, Button #19).
2. Enter a valid Route Number (000-499) to be associated with the DID Number.
This Route Number is the same Route Number in the ICLID Ringing Assignments Table
(FLASH 43)and determines the destination of the DID number associated with this
Route Number. The display shows the route number as it is...

Direct Inward Dialing2-103
Chapter 2 - Features and Operation
Name Assigned to DID Number
Programming Steps
1. Press the NAME flexible button(FLASH 44, Button #3)to enter the desired name for the
DID trunk. Maximum length is 8-characters.
2. Press the HOLD button to update the database. A confirmation tone sounds.
3. Use the BACK SPACE flexible button(FLASH 44, Button #5)to erase the current letter to
correct for errors.
DIDNameandNumberCodes
ThedisplayshowstheDIDnameornumberasitisentered.
Figure 2-5:...

2-104Direct Inward Dialing
Chapter 2 - Features and Operation
DID/ICLID Ringing Assignments
Description
ICLID Ringing Assignments let you change the ring assignment based on the incoming
number received. This feature permits you to select from 500 ringing routes for each entry in
the name to number translation table and DID table (Flash 55). For example, this feature
could be used to reroute selected customers to a specific ACD or UCD group and bypass the
general Attendant.
The Direct Inward Dialing...

Direct Inward Dialing2-105
Chapter 2 - Features and Operation
3. Enter a valid Destination (XXX) and Ring type ( Y ) followed by HOLD. A confirmation tone
sounds and the display updates.
View DID/ICLID Ringing Assignments
Description
Keysets designated to ring on an incoming CO line but not designated to ring on the
DID/ICLID ring, may receive a ring cycle before the call is moved. The same ringing
restrictions applied to CO line ringing are applied to DID/ICLID ringing.
Programming Steps
1. PressFLASH...

2-106Direct Inward Dialing
Chapter 2 - Features and Operation
Ring assignments are continuous and display in order of the destination number from
020-557. A maximum of eight stations display. Additional stations and ringing
assignments are displayed using Button #17.
To advance to the next route:
Press the NEXT flexible button(FLASH 43, Button #18)to advance to the next DID/ICLID
Route number.
To return to a previous route:
Press the PREVIOUS flexible button(FLASH 43, Button #19)to return to the...

Direct Inward Dialing2-107
Chapter 2 - Features and Operation
DID Incoming Signaling
Description
The DID Incoming Signal option allows the installer to determine the type of incoming
signaling used by all T-1 trunks in the system.
Programming Steps
DTMF is the DID Signaling type used for DID Trunks. Do not change the default setting of
DTMF unless instructed to do so by technical support.
1. Press the DID INCOMING SIGNALING flexible button(FLASH 41, Button #5)for
programming the type of DID signaling...

2-108Direct Inward Dialing
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Flexible button #19 (Page A) is lit. The following message displays to indicate current
programming of that line or group of lines:
XXX-XXX = CO Line Range
4. PressFLASH 40, Page A, Button #14. The following message displays:
5. Dial a valid number (0-2) on the dial pad.
[0] = Immediate Start
[1] = Wink Start
[2] = Delay Start
6. PressHOLDtosavetheentry....

Direct Inward Dialing2-109
Chapter 2 - Features and Operation
3. Press Button #21 to select Page C. The display updates. The following message displays to
indicate current programming of that line or group of lines:
XXX-XXX = CO Line Range
4. Press the DID COLLECT TIMER Button(FLASH 40, Page C, Button #9)in the flexible
button field. The following message displays:
5. Enter a valid number on the dial pad that corresponds to 010–200 (100 ms to 2.0
seconds).
6. Press HOLD button to save entry. A...

2-110 Direct Inward System Access (DISA)
Chapter 2 - Features and Operation
Print DID-TIE Parameters
Description
The Print DID-TIE command dumps the entire database as a permanent record which can
serve as a hard copy of the database. The system baud rate must match that of the printer or
receiving device.
When printing the DID-TIE Timers, the following data is printed: