Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

CO Line - Loop Supervision2-81
Chapter 2 - Features and Operation
CO Line - Loop Supervision
Description
TheXTScan be programmed to monitor CO lines while on-hold or connected to RAN devices
or Voice Mail systems, or in Trunk-to-Trunk connections for disconnect signal provided by the
Telco. After a disconnect signal is detected, theXTSreleases the CO lines and automatically
place them back in service.
Loop Supervision Programming
Description
Loop Supervision is used primarily with DISA, Voice Mail/Auto...

2-82CO Line - Queue
Chapter 2 - Features and Operation
CO Line - Queue
Description
When all outside lines in a group are busy, stations can be placed in queue awaiting a line in
the same group to become available. If a station doesn’t answer the queue signal within
15 seconds, that station is dropped from the queue. A station can queue only one line at a
time.
Line Queuing
Description
Stations can be allowed or denied the ability to manually queue for a busy group of CO lines.
Even when disabled,...

CO Line - Queue2-83
Chapter 2 - Features and Operation
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT…CO Line Queuing is enabled at all stations.
Operation
If you see that a particular outside line is busy and you wish to be placed on a list
waiting for that line to become available:
1. Press desired busy OUTSIDE LINE button,
-or-
Press the POOL button. (Busy tone sounds.)
2. Press the preprogrammed CO LINE QUEUE button (621).
3. Replace handset or press ON/OFF button.
To answer a...

2-84CO Line - Ringing Options
Chapter 2 - Features and Operation
CO Line - Ringing Options
Description
When a CO call rings at a busy station, the call rings at the station using a muted ring signal.
This option allows a user to receive a reminder ring at their busy station, instead of muted
ringing. A reminder ring timer is also available to provide the reminder ring every time the
timer expires, as long as the incoming CO line remains connected.
Programming Steps
1. PressFLASHand dial[50]. Flexible...

CO Line - Ringing Options2-85
Chapter 2 - Features and Operation
Transfer CO Ringing
Description
The Transfer CO Ringing flash rate is the rate at which a CO Line button or Loop button
flashes when a call is transferred to you. This flash rate can be programmed to 29 different
options identified in the flash rate table. This enables the programmer to customize the key
system configuration to desired flash rates.
Programming Steps
1. Press the TRANSFER CO RING flexible button(FLASH 07, Button #9). The...

2-86CO Line - Ringing Options
Chapter 2 - Features and Operation
Queued CO Ringing Flash Rate
Description
The Queued CO Ringing flash rate is the rate at which a CO Line button or Loop button
flashes when a queued line becomes available. This flash rate can be programmed to
29 different options identified in the flash rate table. This enables the programmer to
customize the key system configuration to desired flash rates.
Programming Steps
1. Press the QUEUED CO RING flexible button(FLASH 07, Button...

CO Line - Ringing Options2-87
Chapter 2 - Features and Operation
CO Direction
Description
CO Lines can be programmed on a per CO Line basis for the type of CO Line desired:
Incoming

2-88CO Port Parameters
Chapter 2 - Features and Operation
5. Enter a valid number (0-3) on the dial pad which corresponds to the desired CO type:
[0] = Out-of-Service (OOS)
[1] = Incoming Only
[2] = Outgoing Only
[3] = Both Incoming and Outgoing
6. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
DEFAULT…All CO Lines default to both incoming and outgoing type.
Conditions
»For PRI cards, the 24th channel mustbe marked as Out-of-Service (OOS). This is true on all
PRI cards,...

CO Port Parameters2-89
Chapter 2 - Features and Operation
PrintCOPortParametersandFeatureCodes
Description
The Print CO Port Parameters and Feature Codes command dumps the entire database as a
permanent record which can serve as a hardcopy of the database. The system baud rate must
match that of the printer or receiving device.
Figure 2-4: CO Port Attributes Printout
Programming Steps
1. Press the CO PORT flexible button(FLASH 85, Button #4). The following message
displays:
2. To print the CO Port...

2-90CO Ring Detect Timer
Chapter 2 - Features and Operation
CO Ring Detect Timer
Description
The CO Ring Detect Timer controls the time necessary to detect an outside line ringing into
the system. The duration of the ringing signal from the CO or the PBX is matched with ringing
detection circuitry in theXTS. The ring detect can range from 200 ms to 900 ms programmed
in 100 ms increments. This timer helps prevent false ringing.
Programming Steps
1. Press the CO RING DETECT TIMER flexible button(FLASH 01,...