Starplus Triad Xts Installation Digital Key Telephone System Instructions Guide

CO Line - Identification2-71
Chapter 2 - Features and Operation
Programming Steps
Each CO line can be programmed to have a name associated to it in database programming.
1. PressFLASHand dial[40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Flexible button #19 (Page A) is lit. The following...

2-72 CO Line - Incoming Ringing Assignment
Chapter 2 - Features and Operation
CO Line - Incoming Ringing Assignment
Description
Each CO line may be programmed (in database admin) so that incoming ringing on the
specified CO line(s) may be assigned initial ringing to one of the following destinations:

CO Line - Incoming Ringing Assignment 2-73
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Flexible button #19 (Page A) is lit. The following message displays to indicate current
programming of that line or group of lines:
XXX-XXX = CO Line Range
4. Press the RING ASSIGNMENT flexible button(FLASH 40, Page A, Button #10).The
display shows the following information:
5. Enter a valid Destination (DDD) or (DDDD) and Ring type (R)...

2-74 CO Line - Incoming Ringing Assignment
Chapter 2 - Features and Operation
To delete multiple stations:
Enter: DDD0 HOLD DDD0 HOLD...etc.
(Example: 1080 HOLD, 1090 HOLD)
DEFAULT…All CO lines ring at the Attendant, Station 100 during Day and Night Modes.
Incoming CO Line Ringing - Setting Flash Rate
Description
The Incoming CO Line Ringing flash rate is the rate at which an Incoming CO line or Loop
Button flashes. This flash rate can be programmed to 29 different options identified in the
flash rate...

CO Line - Incoming Ringing Assignment 2-75
Chapter 2 - Features and Operation
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Flexible button #19 (Page A) is lit. The following message displays to indicate current
programming of that line or group of lines:
XXX-XXX = CO Line Range
4. PressFLASH 40, Page A, Button #13to display ring assignments. Assignments are
displayed in sets of 8, up to the number programmed. The following format displays the
assignments.
DDD =...

2-76 CO Line - Incoming Ringing Assignment
Chapter 2 - Features and Operation
2. Enter a valid number for the range of lines being programmed. If only one line is being
programmed, enter that number twice (001 001).
3. Press Button #21 to select Page C. The display updates. The following message displays to
indicate current programming of that line or group of lines:
XXX-XXX = CO Line Range
4. Press the RELEASE TIMER Button(FLASH 40, Page C, Button #4)intheflexiblebutton
field. The following message...

CO Line - Incoming Ringing Assignment 2-77
Chapter 2 - Features and Operation
Guard Timer
Description
The outgoing Guard Timer is used to set the length of time a CO is held busy to outgoing
seizure after a valid release is detected. If a user attempts to access a CO line before the Guard
Timer expires, their LED illuminates to indicate that the line is seized, however the CO line is
not actually seized until the timer expires. The user gets a busy tone, and may receive a
delayed CO dial tone if the...

2-78 CO Line - Incoming Ringing Assignment
Chapter 2 - Features and Operation
Tra n s m i t Vo l u m e
Description
Up to ten volume levels are available for each CO Line in the system.
Programming Steps
1. PressFLASHand dial[40]. The following message displays:
2. Enter a valid number for the range of lines being programmed. If only one line is being
programmed, enter that number twice (001 001).
3. Press HOLD to save the entry. A confirmation tone sounds and the display updates.
Flexible Button #19...

CO Line Loop and Pool Buttons 2-79
Chapter 2 - Features and Operation
CO Line Loop and Pool Buttons
Description
A station not having a direct appearance for a CO line receives incoming CO calls and
transferred CO calls under the LOOP button. Only one call at a time can be connected to a
keyset on the LOOP button.

2-80 CO Line Loop and Pool Buttons
Chapter 2 - Features and Operation
4. Press the CO LOOP POOL flexible button (FLASH 50, Page A, Button #17). The following
message displays:
5. Enter a 0 or 1 on the dial pad to enable/disable this feature.
[0] = Disable
[1] = Enable
6. Press HOLD to save the entry. A confirmation tone sounds.
DEFAULT…CO Loop Pool is disabled.
Operation
To make a Loop button:
1. Press the SPEED button twice.
2. Press the desired flexible button.
3. Dial [89].
4. Press HOLD.
In-Use Hold...